Tone Commander 7210, 7220 Ip Centrex Telephone User Manual

							26Tone Commander 7210/7220 User Manual
If DHCP is currently enabled, select DISABLE.
Press the Done key to return to the IP Configuration Update
menu or the Setup key to exit Setup Mode.
Manual IP Configuration
DHCP should be disabled if manual IP configuration is used; IP
addresses configured via DHCP will overwrite manually entered values.
From the Installation Options menu, select IP.
(Setup → INSTL → IP)
Select PHONE, TFTP, GATEWY, iMERGE, SNTP, or
SUBNET.
Using the dial pad, enter the IP addresses. Address format is
four groups of 1-3 digits. You must enter leading zeroes for
each group of digits. Periods are automatically displayed.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous digit.
CLEAR removes all digits, allowing you to start over.
The subnet mask is entered in a similar manner; the default
value of 255.255.255.0 will suffice in most cases.
For SNTP, select OFFSET to specify the time offset (in hours)
from UTC for your local time zone.
PHONE=192.169.073.104
      |BKSP CLEAR  PING
DHCP=DISABLED
ENABLE DISABLE
Done
IP ADDRESSES           \
PHONE GATEWY TFTP iMERGE
IP ADDRESSES           \
 SNTP SUBNET 
						

							Tone Commander 7210/7220 User Manual27
To test the phone, gateway/router, TFTP server, SNTP server,
or iMERGE address, select PING. If you have entered a new
phone IP address, the phone must be restarted before ping
will work properly.
If a response is received, indicating a valid address, PING
SUCCESSFUL will be displayed.
If no response is received, the entered address is invalid.
PING FAILED will be displayed.
Press any key to return to the previous menu.
Alias Entry   _____________________________
A unique iMerge alias is required for operation of the 7210/7220.
Contact your network service provider for your telephone’s alias.
From the Installation Options menu, select ALIAS.
(Setup → INSTL → ALIAS)
If the phone is currently registered with an iMerge alias, select
CHANGE, then YES to restart the phone and clear the
existing alias. The existing SPID and H.235 password will also
be cleared.
PINGING IP ADDRESS...
PING SUCCESSFUL
PRESS ANY KEY
PING FAILED
PRESS ANY KEY
ALIAS=3094770185
|BKSP              CLEAR 
						

							28Tone Commander 7210/7220 User Manual
Using the dial pad, enter the alias supplied by your network
service provider.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous digit.
CLEAR removes all digits, allowing you to start over.
When all digits have been entered, press the Done key to
return to the Change Password menu or the Setup key to exit
Setup Mode.
SPID Entry   _____________________________
A unique SPID (Service Profile IDentifier) is required for operation of
the 7210/7220. If the network supports AutoSPID, a SPID that is
assigned to your ISDN line can be automatically selected. If generic
SPID assignments are used by your service provider, your SPID will
consist of your primary telephone number followed by “0101” for
National ISDN (e.g., 52534910000101). Contact your network service
provider for your telephone’s SPID.
The alias value, if correctly entered, will be copied to the SPID entry.
You can edit this SPID entry if necessary.
From the Installation Options menu, select SPID.
(Setup → INSTL → SPID)
Using the dial pad, enter the SPID number supplied by your
network service provider.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous digit.
CLEAR removes all digits, allowing you to start over.
When all digits have been entered, press the Done key to
return to the Installation Options menu or the Setup key to exit
Setup Mode.
If the phone is currently initialized with a SPID, select
CHANGE, then YES to restart the phone and clear the
existing SPID. The iMerge alias and H.235 password will also
be cleared.
Done
ID=42534910000101
      |BKSP  CLEAR
Done 
						

							Tone Commander 7210/7220 User Manual29
IP Configuration and Software Updates   _____
Telephone operating software and configuration parameters can be
automatically updated daily from the TFTP server at a preset time,
manually updated from the phone using files on the TFTP server, or
updated from a client PC.
Automatic Update
A properly configured network TFTP server is required for automatic
updates. Please refer to the 7210/7220 Network Administration Guide.
From the Installation Options menu, select UPDATE.
(Setup → INSTL → UPDATE)
Select TFTP.
Select AUTO.
If TFTP updates are currently disabled, select ENABLE.
Enter new digits for the update time with the dial pad. The
cursor will advance automatically as each digit is entered.
Time must be entered in 12-hour format. AM/PM is changed
with a softkey.
The minutes value is calculated based on the MAC address of
the phone, to minimize the possibility of multiple phones
TFTP UPDATE TIME=03:26AM
DISABLE     |BKSP  AM/PM
IP CONFIGURATION UPDATE
 DHCP  TFTP FLASH TELNET
TFTP CONFIG UPDATE
START  AUTO
TFTP UPDATE=DISABLED
ENABLE 
						

							30Tone Commander 7210/7220 User Manual
simultaneously requesting updates. You may manually enter
the minutes digits, but it is recommended that you use the
default calculated value.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous character.
When all changes have been made, press the Done key to
return to the IP Configuration Update menu or the Setup key
to exit Setup Mode.
Manual Update
To perform a manual update, the phone must have the TFTP server’s
IP address entered manually or downloaded via DHCP.
From the Installation Options menu, select UPDATE.
(Setup → INSTL → UPDATE)
Select TFTP.
Select START to initiate the manual update.
Restarting indicates that new operating software is being
loaded into the phone. When complete, the phone will restart.
Done
IP CONFIGURATION UPDATE
 DHCP  TFTP FLASH TELNET
TFTP CONFIG UPDATE
START  AUTO
READING CONFIGURATION
FROM TFTP SERVER...
RESTARTING FOR NEW
SOFTWARE DOWNLOAD... 
						

							Tone Commander 7210/7220 User Manual31
If a new version program is not found, the following screen will
be shown. Press any key to return to the previous menu.
If phone configuration files are missing from the TFTP server,
or the correct TFTP server address has not been entered or
set via DHCP, the following screen will be shown.
Select EDIT.
Enter the correct TFTP server address. You can verify the
address by selecting PING. When finished, press the Done
key.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the previous digit.
CLEAR removes all digits, allowing you to start over.
Update from a Client PC
Telephone software can also be updated from a network client PC
running Tone Commanders Flash Update program.
To enable flash updates:
From the Installation Options menu, select IP.
(Setup → INSTL → UPDATE)
TFTP VERS SAME AS PHONE
PRESS ANY KEY
NO TFTP SERVER RESPONSE
 EDIT
IP CONFIGURATION UPDATE
 DHCP  TFTP FLASH TELNET
TFTP=216.122.043.234
      |BKSP CLEAR  PING 
						

							32Tone Commander 7210/7220 User Manual
Select FLASH.
Select ENABLE.
After updating, you can disable flash updates to prevent inadvertent
changes to the phone configuration.
Telnet
This option allows a telnet client to connect to the phone for
troubleshooting purposes.
From the Installation Options menu, select UPDATE.
(Setup → INSTL → UPDATE)
Select TELNET.
Select ENABLE.
When telnet capability is no longer needed, disable it to prevent
inadvertent changes to the phone configuration.
FLASH UPDATE=DISABLED
ENABLE DISABLE
FLASH UPDATE=ENABLED
ENABLE DISABLE
IP CONFIGURATION UPDATE
 DHCP  TFTP FLASH TELNET
TELNET ACCESS=DISABLED
ENABLE DISABLE
TELNET ACCESS=ENABLED
ENABLE DISABLE 
						

							Tone Commander 7210/7220 User Manual33
Configuring Keys   _______________________
If the network does not support ISDN Parameter Download, you must
assign call appearances, directory numbers and feature activators
using this option.
From the Installation Options menu, select KEYS.
(Setup → INSTL → KEYS)
The status indicator for each key will indicate the current
setting.
Green– Call Appearance or DSS.
Red– Feature Activator.
Off– Unused or Speed Dial.
On the phone or expansion module, press the multifunction
key to be programmed.
The selected key’s indicator will alternately flash red and
green.
Select CA/DN (Call Appearance /Directory Number), FA
(Feature Activator), DSS (Direct Station Select), SPDIAL
(Speed Dial), or UNUSED from the menu.
Programming procedures for each key type are described
below.
12=CA/DN# 555-789-4251
|BKSP       ORIG  RESERV
12=CA/DN               \
CA/DN   FA   DSS  SPDIAL
12=CA/DN               \
UNUSED 
						

							34Tone Commander 7210/7220 User Manual
Call Appearance / Directory Number Keys
These “line” keys are used to place and answer calls. If you have
BASIC service, each directory number key is assigned a unique
directory number. If you have CACH EKTS service, one directory
number may be assigned to multiple Call Appearance keys; multiple
calls can be handled on one directory number.
Enter the assigned directory number with the dial pad.
If you need to make corrections while entering numbers,
select 
ÅBKSP (backspace) to delete the previous digit.
You can press the Done key to return to key selection.
Automatic Call Appearance Selection
A call appearance is automatically selected when originating a new
call, answering an incoming call, or conferencing or transferring a call.
Three configuration options determine how call appearances are
selected:
Call Preference (page 64) – determines whether a new call is
originated when you lift the handset or press the Spkr key. If set to
NONE, you must manually press a Call Appearance key to originate
a call.
Originating DN – only call appearances with this option set to YES
will be automatically selected for call origination.
CA Reservation– within the group of originating DNs, call
appearances set for NOT RESERVED are selected first, followed by
OUTGOING ONLY, followed by OUT/PRIORITY call appearances
(OUTGOING ONLY call appearances are selected first for
conferencing and transferring). Within each subgroup, call
appearances are selected in ascending order. INCOMING ONLY
call appearances are never selected for an outgoing call. If an idle
CA is not found, “SELECT AN IDLE LINE” is displayed.
12=CA/DN# 555-789-4251
|BKSP       ORIG  RESERV 
						

							Tone Commander 7210/7220 User Manual35
To change the Originating DN assignment:
Select ORIG.
Select YES or NO from the Originating DN menu.
Press the Done key to return to the CA/DN menu.
To change call appearance reservation:
Select RESERV.
Select the call appearance reservation for this CA/DN.
OUT– Originate (outgoing calls) only.
IN– Terminate (incoming calls) only.
PRI– Outgoing or priority incoming or calls only.
NOT– Not Reserved – default value for all keys.
Press the Done key to return to the CA/DN menu.
Feature Activator Keys
Feature Activator keys must be configured to match network feature
activator codes that have been assigned to your line.
Using the dial pad, enter the feature activator code assigned
by your network service provider.
If you need to make corrections while entering numbers,
select 
ÅBKSP (backspace) to delete the previous digit.
Select CALL if a call needs to be originated when the feature
is activated. When enabled, (CALL) will appear in the top line
of the display as shown above.
With CALL enabled, the feature is always activated within the
context of a call. Features that need to originate a call include
Call Forward (on Siemens EWSD), ICM intercom (on Nortel
DMS-100), and Call Pickup. The CALL feature is not used
with Lucent 5ESS Custom ISDN.
Done
Done
10=NETWORK FA#59  (CALL)
|BKSP              CALL