Tone Commander 7210, 7220 Ip Centrex Telephone User Manual

16Tone Commander 7210/7220 User Manual
Using a Headset   ________________________
Headset Mode Operation
Your telephone can be set for handset or headset use (see page 65).
With a headset, the Spkr key is used as the hookswitch, and the
speakerphone feature is disabled.
Optimizing the Phone to Match Your Headset
Headset models may vary in their microphone sensitivities and receive
levels. Your telephone provides adjustments for transmit and receive
levels to accommodate most headsets – see page 65....

Tone Commander 7210/7220 User Manual17
Installation
Ordering ISDN Service   ___________________
ISDN ordering forms may be supplied by your service provider. You
can also print forms using the PC-based Configuration Wizard. Please
refer to Appendix A in this manual.
Consult your service provider to plan your service installation. Allow
adequate time after cutover for testing of all call appearances and
programmed features. Ask your service provider for your alias and
H.235 password, and confirm the...

18Tone Commander 7210/7220 User Manual
Power
Power must be provided by the Tone Commander 901034 power
supply. Connect power after all other connections are complete. The
7210 and 7220 are not compatible with IEEE LAN-based power.
Plug the power supply barrel connector into the round jack on the
bottom of the phone (under the speaker). Connect the power supply to
a standard 120 VAC, 60 Hz grounded power outlet.
Wall Mounting   __________________________
Robust handset retainer clips for wall mount use...

Tone Commander 7210/7220 User Manual19
Configure the Set   _______________________
ISDN configuration is performed automatically in many cases. The
telephone set will detect the switch type, set the SPID number, and
download other setup parameters when these features are available
from the central office.
You will be prompted for any required setup information that cannot be
set automatically.
Initialization
A self-test is performed upon power up, followed by terminal
initialization. Initialization...

20Tone Commander 7210/7220 User Manual
Alias
If the alias is rejected by iMerge or there is no stored alias, the
following will be shown:
Enter the correct alias as supplied by your service provider,
then press the Done key.
H.235 Password
If H.235 password is rejected by iMerge or there is no stored password,
the following will automatically be shown:
Enter the correct password as supplied by your service
provider, then press the Done key. If passwords are not used,
press the Done key with no entry.
To...

Tone Commander 7210/7220 User Manual21
number. Enter the number with the dial pad, then press the Done key.
BKSP (backspace) deletes the previous digit.
National ISDN– enter your full 10-digit telephone number
(including area code)
5ESS Custom ISDN– enter your 7-digit telephone number
Parameter Download (National ISDN only)
Parameter Download is a network feature that identifies Call
Appearance and Feature Activator keys that are assigned to your line
so that your phone may be configured automatically....

22Tone Commander 7210/7220 User Manual
Using Local Inspect to Verify Keys
Local Inspect allows you to identify the call appearance or feature
assignment of each configured key, directory number bearer
capabilities, and the feature indicator assignment for the Message
Indicator. Please refer to page 47.
Customize your Phone   ___________________
You can set the following options on your phone.
DSS – converts Call Appearance keys to Direct Station Selection keys
with busy lamp indication for one-button...

Tone Commander 7210/7220 User Manual23
Voice Mode
Handset/Headset Mode – selects handset or headset operation
(page 65).
Preset Volume Levels – sets handset and headset volume levels,
and speakerphone transmit level (page 65).
Display Contrast – adjusts the contrast of the display for best visibility
(page 67).
Call Log Password – sets or removes a password to control entry into
the call log (page 68).
Voice Announce – enables or disables automatic call answering by
the speakerphone (page 39).
Label the...

24Tone Commander 7210/7220 User Manual
Installation Options
Options in this section are typically set at the time of installation. Many
options can be set automatically by the DHCP, TFTP, AutoSPID,
Automatic Switch Detect, and Parameter Download features, if
supported on the network.
The following options can be changed from the Installation Options
menu:
• IP Addresses• Voice Announce
• Alias• Parameter Download
• SPID•  Quality of Service
• Configuration Updates• Installation Password
• Key...

Tone Commander 7210/7220 User Manual25
A password may be set to prevent unauthorized
entry into the Installation Options menu.
When prompted for a password, enter your 4-digit
password with the dial pad. Press the Done key
after entering the password.
To change or remove the password, please refer to
page 43.
IP Addresses   ___________________________
IP address entries are required for the phone, subnet mask,
gateway/router, iMerge, and optional TFTP and SNTP servers. The
default setting uses DHCP to...