Home > Triad > Communications System > Starplus Triad S System Programming Manual

Starplus Triad S System Programming Manual

Here you can view all the pages of manual Starplus Triad S System Programming Manual. The Triad manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 131

2-84 L ocal Number / Name Transla tion Table 

Page 132

3
CO Line Attributes
Programming
Thi s chap te r de scr ibe s t he pr oced ure s and s te ps ne cess ar y to pr ogr am CO
Line attributes. If the system is in the programming mode, continue using
the  pr o gra m c o des . If  st art i ng to  pr o gr am he re , yo u  mu s t fi rs t e nt er  the
pr ogra mmi ng mode.  Re fe r to Fi gu r e 1- 2:  Pro g ra mmin g  B u tto n  M a pp i n g in
chapter 1. 

Page 133


				            

Page 134

Page A  Introduction 3-3
Page  A  In troduction
Pro g ram mi ng  S te ps
1. Press FLASH and  di al  [40 ].  The following message displays:
2. Enter a valid number for the range of lines being programmed. If only 
on e l in e i s  bei ng  prog ram med,  ent er  t hat  num ber  t wi ce  (0 0 1  00 1) .
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.  Flexible Button #19 (Page A) is lit.  The following 
message displays to indicate current  programming  of that...

Page 135

3- 4 Page  A I ntr o ducti o n
By de faul t , Pag e A  i s  shown.
DTMF / Dial Pulse Programming
Pro g ram mi ng  S te ps
1 . Pr es s t he  DT M F/ DI AL  P ULSE  fl ex ibl e  but ton (FLASH  40, Page A, 
Bu tton  #1).
2. Enter a 0 or 1 that corresponds with the following entries:
[0] =  Dial Puls e
[1] =  DT MF
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
Each  ind iv idua l  outs ide line can  be programmed to b e D TMF  (ton e) o r 
dial  pulse. By  default,  all...

Page 136

Page A  Introduction 3-5
CO /  PBX Programming
Pro g ram mi ng  S te ps
1 . Pr es s t he  CO /P BX  fl exi bl e b utt on ( FLA SH 40,  Pag e A, Butto n #2). 
2 . Ent er  a  0 or 1 whic h c orr es ponds  wi th the  fo ll owing ent r ie s:
[0] =  PBX 
[1] =  CO 
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
Each ind iv idua l outs ide line connected to the sy stem may be 
programmed as a  CO or PBX line.  Use the PBX mark when identifying 
Ce ntrex  line s.  By de fault,...

Page 137

3- 6 Page  A I ntr o ducti o n
DIS A CO- to- CO
Pro g ram mi ng  S te ps
1. Press the DISA CO-TO-CO  flexible button ( FLASH 40, Pag e  A, 
Bu tton #4).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
The DISA  CO-to-CO (or Conference)  mark on  the CO line governs  a DISA 
caller’s  ab ility  to  acces s other ou tside  line s.  CO line s m ust hav e  DIS A CO-
to- CO  e...

Page 138

Page A  Introduction 3-7
Pr iva cy
Pro g ram mi ng  S te ps
1 . Pr es s t he  P R IVAC Y  fl exi bl e b utt on ( FLA SH 40,  Pag e A, Butto n #5).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Disabling Privacy F unction
The  sy st em  c an b e p rogr amm ed  to  el imi nat e  CO  Li ne  P ri vac y , whi c h 
allows  anothe r  station  to  join e xis ting o uts ide  line  conv ersations...

Page 139

3- 8 Page  A I ntr o ducti o n
B y de fau lt , P r iva c y i s e nab le d for  a ll  CO  Li nes .
Loop Supervision Programming
Pro g ram mi ng  S te ps
1 . Pr es s t he  LOO P  SUP V  fl exi ble  b utt on ( FLASH 40, Pag e  A, Button  #6).
2. Enter a valid number (1-9) on  the dial pad which corresponds to 
100-900 ms. (0 = disabled).
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
Loop  Supe rv is ion  is  use d p ri mar il y w it h DI S A,  Voi...

Page 140

Page A  Introduction 3-9
DISA Programming
Pro g ram mi ng  S te ps
1. Press the DISA flexible button (FLASH 40, Page  A, Bu tton  #7).
2 . Ent er  a  val id  numbe r  (0 -5 ) on  the  di al  pa d t o i ndi ca te  t ype  of  DI SA 
desired.
[0] =  No D IS A
[1] =  24-H our  DISA
[2] =  Ni ght  DISA
[3] =  24-H our  DISA with  forwarding
[4] =  Night  DISA with  forwarding
[5] =  Telecen te r  24-Hour D IS A  with f orward ing
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the...
Start reading Starplus Triad S System Programming Manual

Related Manuals for Starplus Triad S System Programming Manual

All Triad manuals