Starplus Triad S System Programming Manual

3-20 Page  B I ntro ductio n
Des crip ti on
Up to ten volume levels are  available  for each CO Line in the  system. By 
def aul t,  al l  CO  li ne s a re  pr ogr amme d for  l ev el  5  (0  dB) .
Preset Call Forward Destination
Pro g ram mi ng  S te ps
1. Press the PRESET  FWD DESTINATION  flexible button ( FLASH 40, 
Page B, Bu tton #2). The following  message displays:
2 . Ent er  a  val id  for war d d est i nat ion  on t he  di al  pad.
[1020- 1999] =  Sy ste m S pe ed  Bins
[1 00 -1 31 ] = Triad-S...

Page B Introduction 3-21
Preset Forward  Voice Mail ID
Pro g ram mi ng  S te ps
1 . Pr es s t he  P RES ET  FWD  VM I D f le xibl e  but ton  (FLASH  40, Page B, 
Bu tton  #3).  The  fo ll owing  mes sag e d is pla ys:
2. Enter a valid number on the dial pad that corresponds to 0000-9999 
for Voice Mail ID digits.
3. Press HOLD to complete  the entry.  A  co nfirmation tone  is heard and 
t he  di spl ay  updat es .
Deleting N um bers  Currently Entered
1 . Pr es s [ #] b u tt o n f o u r  ti me s.
2....

3-22 Page  B I ntro ductio n
Des crip ti on
UDA -a ssi gne d CO  li nes  can si gnal  ove r e xte r nal  p age  port (s ). Ext e rna l Da y 
ri ngi ng i s  prog ram med  on a  sys te m-w ide  ba si s i n a dmin is tr at iv e 
progra mming. S ta tions  tha t  do not h ave  acce ss  to  a line  du ring the  day 
can answer  that  line  while the System is in the day  mode by  dialing  a 
UDA  code  [# 5] . T o use  t hi s fe at ure ,  a LO O P  but ton  or  an a ppe ar ance  of 
the  t r u nk mu s t  be...

Page B Introduction 3-23
Des crip ti on
The Music-On-HOLD feature allows a user  to  select  the Music-On-Hold 
c hanne l  for  ea c h CO  l ine .  Thi s f eat ur e  le ts  t he s yst em  as si gn CO  l i ne 
circuits  as  additiona l m usic in puts . This increas es  the ca pacity  of mus ic 
channels beyond  the two available on  the MISU  to  be  used for MOH 
sources. A total of eight channels are available for use on the system. The 
CO  li ne ca n be  ass igne d t o NO T PLA Y musi c for  call e rs...

3-24 Page C I ntro ductio n
Des crip ti on
The  ring   tone  signal us ed  to  notify  stations  of  an incoming call can b e 
changed in administrative programming  to  provide  distinctive ringing 
on a  pe r  CO  line  bas is . A d istinctive  ring  tone  ca n be  programme d f or 
ea ch  CO line  that ring s e ach s ta tion.  The  sy stem  prov id es  36 diffe rent 
ring p atte rns  that can  be  se le cte d f or  each  CO line  in the  sys te m. By  
def ault,  Ring  Tone  is  set f or  00...

Pa ge C  I ntr o ducti o n 3 - 25
Des crip ti on
When entering  the CO Line attributes portion of the  database, the 
programmer may decide  to  enter information for a  range  of CO lines or 
one  spe cifi c CO Li ne.  Range  programmi ng l ets the  pro gra mmer chan ge a  
specific parameter  or a few parameters  for an  entire range of CO  lines, 
leaving  intact the  remaining data  fields that do not require change. 
Thos e  dat a fi e lds  c ont inue  t o op er at e wi t h t he  pr evi ousl y p...

3-26 Page C I ntro ductio n
Des crip ti on
Fl ash  is  a  prog ra mmabl e  ope ning  on a  li ne  for si gna li ng.  When  usi ng a n 
outs id e l i ne,  fl ash  le ts  a  use r ob ta in  a ne w d ial  t one  wi thout  l osi ng t he  
line.  T his  is  pa rticularly use ful be hind a  PBX or Ce ntre x.  Each  CO  line  can 
be  pr ogra mme d for  a  fl ash  ti me . By  def ault ,  the  F la sh T ime r  is  s et  for  1 0 
(1 .0 se conds) and is var i abl e from  01 -2 0  (1 00 ms  t o 2  se conds).
Ring...

Pa ge C  I ntr o ducti o n 3 - 27
Reseize Timer
Pro g ram mi ng  S te ps
1. Pres s the RESEIZE  TIMER Button  (FLASH  40, Page C, Button  #3) in 
the flexible button field. The  following message  displays:
2. Enter a valid number on the dial pad that corresponds to 000–255 
(0ms to 2.55 seconds).
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The Reseize  Timer option lets the user adjust the Reseize Timer on a per 
CO  Li ne  bas is . T he  Re...

3-28 Page C I ntro ductio n
Des crip ti on
The outgoing Guard  Timer is  used to set the length  of time  a CO is  held 
busy  t o out going  se iz ur e  aft er  a  val id  r el eas e  is  de te cte d.  If  a us er  
at te mpt s  to   ac c es s a  CO  l ine  be fo r e  the  Gu a rd  Ti mer  e xpi re s,  th ei r  LED 
illuminates to indicate  that  the line is seized, however the CO line is not 
actually seized until the timer expires. The user gets a busy tone, and may 
receive a  delayed CO  dial  tone...

Mi scel l ane ous  C O  Par am eter s 3 - 29
Misce llaneous CO Parameters
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode  first.
1. Press FLASH and  di al  [41 ].  The following message displays:
2 . Se le c t  any  fea tur e  by p re ssi ng t he  ap prop ri at e f le xib le  but to n(s)  in 
the flexible  field.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the...