Starplus Triad S System Programming Manual

2-54 Prog ra mmable Flash  Rat es
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The Do  Not Disturb Button flash  rate is the rate at  which  your  Do Not 
Disturb  Button  fla she s whe n y ou place  your station in a  Do N ot  Dis turb 
mode . T his  fl ash  ra te  can  be  pr ogr amme d t o 2...

Syst em Parame ters 2 -55
Sy s t e m  P a ra m e t e r s
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode.
Pr es s FLASH and  di al  [09 ].  The following message displays:
Des crip ti on
Thi s  sect i on de scr ibe s  the  pr oced ure s a nd s te ps  nece ss ary  t o pr ogr am 
System Parameters in the System  Parameters  programming area. The 
buttons  on  the digita l telephone are  shown...

2-56 Syst em Paramet ers
MOH Assignments
Pro g ram mi ng  S te ps
1. Press the MUSIC  CH  # flex button (FLASH 09, Butto n #1 
thro ugh #6). T he  foll owi ng me ss age  di spl ays:
X=  3 - 8
YYY = CO  Line number
2 . Ent er  a  val id  nu mbe r  (0 01 -0 1 2)  tha t  co rr es po nds  to   the  CO  l in e 
nu mber d esired.
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
The  MO H A ssi gnme nt s f eat ur e e nab le s t he  sys te m t o a ssi gn  CO  li ne  
circuits  as...

Att endan t St ation  Ass ignment 2 -57
Figure 2-2: Wiring - M usic S ourc e to a  CO Line
Attendant Station A ssignme nt
Pro g ram mi ng  S te ps
1. Press 
FLASH and  di al 
[10]. The  following message displays:
2. Enter a  valid  station  numbe r  (10 0- 131) on  the  di al  pa d.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The system identifies an attendant station for the purpose of receiving 
re calls  and  activ ating  night s ervice....

2-58 Sys tem  Tim e an d  Da te
Sy s t e m  T i m e  a n d  Da t e
Pro g ram mi ng  S te ps
To  set the time and date that appears on display telephones:
1. Press FLASH and  di al [11]. The  following message displays:
MM M =  Month
DD = Day
YY  = Ye a r
HH = H ou r
MM  =  Minute
2 . Choos e d is pla y for mat  by  pr es si ng t he  appr opr ia te  but t on i n t he 
f le xib le  but ton  fi el d. T he  ti me  can b e  dis pl ayed  in  th e s ta ndar d 
12-hour format or the 24-hour  format
3 . Di al  th...

PBX Dia ling  Codes 2 -59
By defau lt, the  time is set for 12 hour display  format. When entering 
the  t i me  and d ate , u s e  the  fo l l ow ing  dat a:
LED  O ff =  1 2  Hour  Di sp lay
LED  O n =  24 H our  Di spl ay
PBX Dialing Codes
Pro g ram mi ng  S te ps
1. Press FLASH and  di al [12]. The  following message displays:
2. Enter valid numbers  (one  right after  the other) on the dial pad,  up to 
t en  di git s.  I f a  si ngle  di gi t  code  is  re qui re d, e nte r  code  fol lowe d by...

2-60 Execu tive /  Secret ary Pairs
Executive / Secretary Pairs
Pro g ram mi ng  S te ps
1. Press FLASH and  di al [13]. The  following message displays:
The  fi rs t but ton is  l it  i ndi ca ti ng t he  fi rs t pai r may be pro gram med.
2. Enter a valid Executive station  number.
3. Enter a valid Secretary station number.
4. Press HOLD to save the data. A confirmation  tone is heard and the 
display updates.
†To  pr ogra m a  se cond  pa ir,  pre ss  th e s econd  fl exi ble  b utt on i n t he 
fl...

On-B oard Relay Programmin g 2 -61
On-Board Relay  Programming
Pro g ram mi ng  S te ps
1. Press FLASH and  di al [14]. Button #1  is lit to indicate Relay  #1 is 
se le cte d. T he  fol lowi ng me ss age  di spl ays:
X = 1- 2
YYYYYYYYYYYY = Ext  Page Zone 1-2, LBC  Sta  XXX,  Ran S tart X,  CO Control  XX
2. Press the button that corresponds to the  desired  relay.  That button 
lights . E nter  one  of the  following s equences  on  the keypa d:
[1] +  [1] Ex te rna l  Pa ge Zon es
[2] + [ 1  through...

2-62 B aud R ate  Ass ignment s
Baud Rate  Assign ments
Pro g ram mi ng  S te ps
Pre ss FLASH an d di al  [1 5].  The first  button is lit and ready for 
pr ogra mmi ng Por t  #1. T he  foll owi ng me ss age  di spl ays :
Des crip ti on
The  Tr iad-S  Sys tem p rovides outputs  such a s S MDR or ICLID  to  the 
optiona l  RS -232  con nectors  on the MIS U.
Port #1, #2, #3 Baud  Rates
Pro g ram mi ng  S te ps
1 . Pr es s t he  de si re d PO RT #  fl ex  but ton (FLASH 15, Bu tton s #1, #2, 
or # 3) to...

Ne t wo r k i n g  Ta b l e s 2 - 63
Des crip ti on
Port #1 -- Firs t RS-232C  port on the optiona l MISU
Port #2 -- Second RS -232 po rt on  the optional MIS U
Port  # 3 -- Op ti onal  Mode m
By default, Port #1 (MISU RS-232C), Port #2 (MISU RS-232) and Port #3 
(Modem ) ba ud rates  are  set f or  9600.
Ne two rk i n g  Tab l es
Pro g ram mi ng  S te ps
1. Press FLASH and di al [16]. T he  foll owi ng me ss age  di spl ays:
2. Press the desired bu tton, make the  necessary entry, and then  press 
H OLD...