Home > Sony > Projector > Sony Projector Vpl Vw10ht User Manual

Sony Projector Vpl Vw10ht User Manual

Here you can view all the pages of manual Sony Projector Vpl Vw10ht User Manual. The Sony manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 31

31 (GB)
Attaching the projector suspension support PSS-610
When installing the projector on the ceiling, use the
PSS-610 Projector Suspension Support. For more
details on the ceiling installation, refer to theInstallation manual for Dealers of the PSS-610. The
installation measurements are shown below when you
install the projector on the ceiling.
Installation Diagram
Top view
Align the center of the lens with the center of the screen.
Front of the cabinet Distance between the screen
and the center of...

Page 32

32 (GB)
Notes for Installation
Notes for Installation
Unsuitable Installation
Do not install the projector in the following situations.
These installations may cause malfunction or damage
to the projector.
Poorly ventilated
•Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on surfaces
(rugs, blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.
When the internal heat builds up due to the block-up,
the temperature sensor will...

Page 33

33 (GB)
Notes for Installation
Blocking the ventilation holes
Avoid using something to cover over the ventilation
holes; otherwise, the internal heat may build up. 

Page 34

34 (GB)
Maintenance
Notes
•If the lamp breaks, consult with qualified Sony
personnel.
•Pull out the lamp unit by holding the handle.  If you
touch the lamp unit, you may be burned or injured.
•When removing the lamp unit, make sure it remains
horizontal, then pull straight up.  Do not tilt the lamp
unit.  If you pull out the lamp unit while tilted and if
the lamp breaks, the pieces may scatter, causing
injury.
Replacing the Lamp
When the lamp becomes darker, replace the lamp
promptly with a new LMP-P200...

Page 35

35 (GB)
Maintenance
6Close the lamp cover and tighten the screw.
7Turn the projector back over.
8Connect the power cord and turn the projector to
the standby mode.
9Press the following keys on the control panel in
the following order for less than in five seconds
each: RESET, 

Page 36

36 (GB)
Troubleshooting
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem, using the following
guide.  If the problem still persists, consult with qualified Sony personnel.
Power
Image
Symptom
CauseRemedy
The power is not turned on.
The power has been turned off and on
with the I / 1 key at a short interval.Wait for about 120 seconds before turning on the
power 
(see page 20 (GB)).
The lamp cover is detached.Close the lamp cover securely 
(see...

Page 37

37 (GB)
Troubleshooting
Others
SymptomCauseRemedy
The LAMP/COVER indicator
flashes.The lamp cover or the air filter cover is
detached.Attach the cover securely 
(see pages 34 (GB) and
35 (GB)).
The LAMP/COVER indicator
lights up.The lamp has reached the end of its life. Replace the lamp (see page 34 (GB)).
The lamp becomes a high temperature. Wait for 120 seconds to cool down the lamp and
turn on the power again (see page 20 (GB)).
The TEMP/FAN indicator
flashes.The fan is broken. Consult with qualified...

Page 38

38 (GB)
Specifications
Specifications
Optical characteristics
Projection system 3 LCD panels, 1 lens, projection
system
LCD panel 1.35-inch p-Si TFT LCD panel
3,147,264 pixels
(1,049,088 pixels × 3)
Lens Approx. 1.2 times zoom lens
f 44.6 to 53.6 mm/F 2.2 to 2.5
Lamp 200 W UHP
Projection picture size
Range: 40 to 300 inches (diagonal
measure)
Light output ANSI lumen
1) 1000 lm
Throwing distance

40-inch: 1260 to 1470 mm
(49 
5/8 to 58 inches)
60-inch: 1930 to 2240 mm
(76 to 88 
1/4 inches)
80-inch: 2600...

Page 39

39 (GB)
Specifications
VD:
Vertical sync input: 1-5 Vp-p
high impedance, positive/
negative
REMOTE RS-232C: D-sub 9-pin (female)
CONTROL S IN/PLUG IN POWER
Stereo minijack 5Vp-p, plug in
power, DC5V
TRIGGER Power on: DC 12V
4.7k ohm output impedance
Power off: 0 V
Safety regulations: UL, cUL (CSA), FCC Class B, IC
Class B, EN60 950, CE, C-Tick
General
Dimensions 395 × 168 × 427 mm (13 3/8 × 5 5/8
× 13 1/4 inches) (w/h/d)
Mass Approx. 8 kg (17 lb 10 oz)
Power requirements
AC 100 to 240 V, 50/60 Hz
Power...

Page 40

40 (GB)
Specifications
Dimensions
Unit: mm (inches)
Front
Top
Center of the lens
Center of the unit
395 (15 9/16)
334 (13 5/32)
167 (6 9/16)
80 (3 5/32)40 (1 9/16)
111 
(4 3/8)
99.5 
(3 29/32)
131 
(5 5/32)
168 
(6 5/8)
3(1/8)
96 (3 25/32)
426.5 
(16 
25/32) to 429.5 
(16 
29/32) 
Start reading Sony Projector Vpl Vw10ht User Manual

Related Manuals for Sony Projector Vpl Vw10ht User Manual

All Sony manuals