Sony Projector Vpl Vw10ht User Manual

11 (GB)
Location and Function of Controls
Control panel
1 I / 1 (on / standby) key
Turns the projector on and off when the projector is in
the standby mode. The ON/STANDBY indicator
lights in green when the power is turned on.
When turning off the power, press the I / 
1 key
twice following the message on the screen, or press
and hold the key for about one second.
For details on steps for turning off the power, see “To turn
off the power” on page 20 (GB).
2 INPUT key
Selects the input signal. Each time...

12 (GB)
Connector panel
1 INPUT A connectors
G/Y, B/C
B/PB, R/CR/PR, SYNC/HD, VD connectors
(phono type):
Connect to the RGB output of the equipment.
According to the connected equipment, computer,
component (Y/C
B/CR),  HDTV or DTV (DTV GBR,
DTV YP
BPR) signal is selected.
2 INPUT B connectors
G/Y, B/C
B/PB, R/CR/PR, SYNC/HD, VD connectors
(phono type):
Connect to the RGB output of the equipment.
According to the connected equipment, computer,
component (Y/C
B/CR),  HDTV or DTV (DTV GBR,
DTV YP
BPR)...

13 (GB)
Remote Commander
The keys which have the same names as on the
control panel function identically.
You can control a connected computer using the
Remote Commander.
For details, see “Connecting with a Computer” on page
16 (GB).
1 I (ON) key
Press this key to turn on the projector.  (It is assumed
that the projector is in the Stand-by state.)
2 
1 (OFF) key
Press this key to turn off the power immediately.
3 INPUT SELECT keys
Select the input signal.
VIDEO: Selects the signal of equipment connected...

14 (GB)
Location and Function of Controls / Installing the Projector
Be sure to
install the
battery from
the # side.
Battery installation
1Push and slide to open the lid, then install the two
size AA (R6) batteries (supplied) with the correct
polarity.
2Replace the lid.
Notes on batteries
• Make sure that the battery orientation is correct when
inserting batteries.
• Do not mix an old battery with a new one, or
different types of batteries.
• If you will not use the Remote Commander for a
long time,...

15 (GB)
Connecting
When making connections, be sure to:
•
turn off all equipment before making any connections.
•use the proper cables for each connection.
•insert the plugs of the cables properly; plugs that are
not fully inserted often generate noise. When pulling
out a cable, be sure to pull it out by the plug, not the
cable itself.
Connecting with a VCR/15k RGB/
Component/Progressive
Component Equipment
This section describes how to connect the projector
with a VCR, external active speakers, and 15k...

16 (GB)
CONTROL S IN VIDEO IN
TRIGGER
REMOTEINPUT A
INPUT  B
PLUG IN POWER
RS-232C
(FOR SERVICE USE)S VIDEO
G/Y B/C
B/PBR/CR/PRSYNC/HD VD VIDEO
G/Y B/CB/PBR/CR/PRSYNC/HD VD
Connecting
Connecting with a Computer
This section describes how to connect the projector to
a computer.
Select the “COMPUTER” in the INPUT-A or
INPUT-B of the SET SETTING menu.
Notes
•This unit accepts the VGA, SVGA, XGA or SXGA
signals. However, we recommend you to set the
output signal of your computer to the XGA.
•If you set your...

17 (GB)
Selecting the Menu Language
Selecting the Menu Language
You can select the language for displaying in the
menu and other on screen display. The factory setting
is ENGLISH.
1Plug the AC power cord into the wall outlet.
2Press the I / 1 key to turn on the power.
3Press the MENU key.
The menu display appears.
4Select the icon of SET SETTING Menu, the third
one, by using the M or m key, then press the , or
ENTER key.
 The SET SETTING Menu appears.
LAMP/
COVERTEMP/
 FANPOWER
SAVINGON/
STANDBY
MENU...

18 (GB)
Projecting
4Press the INPUT key to select the input source.
INPUT-A:Selects video signal input from the INPUT
A  connector, such as component
equipment.
INPUT-B:Selects video signal input from the INPUT
B  connector, such as component
equipment.
VIDEO:Selects video signal input from the VIDEO
(VIDEO IN) jack.
S-VIDEO:Selects video signal input from the S
VIDEO (VIDEO IN) jack.
5Press the PATTERN key on the control panel to
display the test pattern, and turn the focus ring to
adjust the focus....

19 (GB)
Projecting
To correct the trapezoid
When the projecting image is a trapezoid, change the
projector’s position/height by moving the adjuster.
For details on “How to use the adjuster”, see page 10 (GB).
If the image is still a trapezoid, correct it in DIGIT
KEYSTONE in the INSTALL SETTING menu.
When the base edge is longer than the upper
edge as shown in the figure below:
When the upper edge is longer than the base
edge as shown in the figure below:
Note
If “ZOOM”, “FULL” or “NORMAL” have been...

20 (GB)
When the 16 : 9 picture is displayed on the
4 : 3 screen
Example: The 120 inch screen is used.
4:3 screen 16:9 picture
Unit (mm) Unit (mm)
80 73
100 91
120 110
2,438
1,829
1,371
2,438 2,032
1,524
1,143
2,032 1,219 1,626
914.6
1,626
1,829 1,371
The 110 inch picture is displayed.
Size
(Inch) Size
(Inch)
To turn off the power
To turn off the power from the control panel
1Press the I / 1 key on the control panel.
“Power OFF?” appears on the screen.
Note
The message will disappear if you press any...