Sharp SF 2530 User Manual

39
GENERAL INFORMATION
POWER SAVE
START
1
23
456
7
0
C 8
9
AUDITING PROGRAMS
Auditing programs
Program No. 10: Auditing mode
If the auditing mode is enabled, copying is limited to operators with an
assigned 3-digit account number. A maximum of 49, 3-digit account
numbers can be assigned. Use program No. 11 to register account
numbers.
When program No. 10 is entered, the current setting (0: OFF, 1:ON)
will blink on the right side of the copy quantity display.
1. Select the desired setting using the 10-key...

40
GENERAL INFORMATION
Program No. 12: Account number change
Program No. 12 is used to change account numbers. When program
No. 12 is entered, an account number will appear in the copy quantity
display.
lIf no account number has been registered, Ò2EÓ will appear in the
copy quantity display for approximately 5 seconds. Enter another
program number or press the 
 key to exit the auditing program.
1. To delete an individual account, press key 0 on the 10-
key pad.
To delete all accounts, press key 1.
2....

41
GENERAL INFORMATION
100%
ZOOM
456
7
0
C 8
9
Program No. 14: Number of copies per account
Program No. 14 is used to display the total number of copies made
against each account number. When program No. 14 is entered, an
account number will appear in the copy quantity display.
1. Use a ZOOM (, ) key to select the account
number.
2. Press and hold the 0 key.
lThe number of copies made against the specified account
number will be displayed. The number will appear in three steps,
each with two digits (the...

42
GENERAL INFORMATION
Program No. 15: Resetting account
Program No. 15 is used to reset all accounts or to reset any desired
individual accounts. When program No. 15 is entered, Ò0Ó will blink on
the right side of the copy quantity display.
1. To reset an individual account, press key 0 on the 10-key
pad.
To reset all accounts, press key 1.
2. Press the START key.
lIf you have pressed key 0 in step 1, an account number will
appear in the copy quantity display. Proceed to step 3.
lIf you have pressed key...

43
GENERAL INFORMATION
POWER SAVE MODES
The copier has two power save modes to reduce overall power consumption
and thereby reduce the cost of operation. In addition, these modes conserve
natural resources and help reduce environmental pollution. The two power
save modes are preheat mode and auto power shut-off mode.
lUser programs
The preheat activation time and the auto power shut-off time have been
preset at the factory to 15min. for preheat mode and 60 min. for auto power
shut-off mode. These times...

44
GENERAL INFORMATION
Power save modes
POWER SAVE MODES
Setting the power save modes
The factory default settings for the power save modes are OFF for the
auto power save control function and ON for the preheat and auto
power shut-off modes.
The auto power save control function can be enabled or disabled as
desired using user program No. 4. If this function is disabled, the time
that elapses before the copier enters a power save mode after any
operation is made can be set manually. This time is set with...

45
GENERAL INFORMATION
User maintenance
USER MAINTENANCE
The document glass and document cover must be kept clean to
avoid dirty areas from being copied onto the copies.
Document glass and document cover
Wipe the document glass and document cover with a
soft, clean cloth.
lIf necessary, dampen the cloth with water. Do not use thinner,
benzene, or similar volatile cleaning agents.
lIf an optional document feeder (ADF or RADF) is installed, wipe
the transport belt with a soft, clean cloth.
Downloaded From...

46
GENERAL INFORMATION
COPIER TROUBLE?
Copier trouble?
Problem Solution
lCopier plugged in? Plug the copier into a grounded outlet.
Copier does not operate.
lPower switch on? Tur n the power switch on.
lCopy density properly See pages 9 and 20.
adjusted?
Copies are too dark or
too light.
lAre theindicator and the Contact your Sharp Service Center as
copy quantity display blinking? soon as possible. See page 28.
Blank copies.
lIs the original placed face down Place the original face down on the
on the...

47
GENERAL INFORMATION
COPIER TROUBLE?
Copier trouble?
Problem Solution
lDocument glass or document Clean regularly. See page 45.
cover dirty?
lOriginal smudged or blotchy? Use a clean original.
Dust, dirt, smudges
appear on copies. Developer is required. Contact your
lIs theindicator on? Sharp Service Center as soon as
possible. See page 28.
Maintenance is required. Contact your
lIs theindicator on? Sharp Service Center as soon as
possible. See page 29.
Wait until war m-up is complete.
lIs the START key...

48
GENERAL INFORMATION
Problem Solution
lIs  steadily lit in the copy The copier is in the auditing mode. Enter
quantity display? your account number using the 10-key
pad. See page 8.
lIs the  indicator blinking?Toner is required. See page 6, ADDING
Power is on but copying TONER.
is not possible.
lIs the  indicator blinking?A misfeed has occurred. See page 22,
MISFEED REMOVAL.
lIs the  indicator blinking?Toner collecting container is full. See
page 27, USED TONER DISPOSAL.
If a problem persists after...