Sharp SF 2530 User Manual

19
MAKING COPIES
Interrupt
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
lReduction/enlargement/zoom, exposure adjustments, dual page
copying, edge erase, and margin shift can be selected during
interrupt copying.
lDuplex copying, sort, group, and staple sort cannot be selected
during interrupt copying.
lINTERRUPT will not function during duplex copying or when an
optional auditor (SF-EA12) is used and the copier has been
programmed in...

20
MAKING COPIES
Automatic exposure adjustment
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying
needs.
1
Ensure that the copier is in the AUTO exposure mode.
2
Open the front cover.
3
Press and hold the EXPOSURE key for more than 3
seconds.
lOne or two exposure indicators corresponding to the automatic
exposure level which has been selected will light up. The factory
default setting is level Ò3Ó.
4
Press the LIGHT or DARK key to lighten or darken the...

21
MAKING COPIES
Toner save mode
TONER SAVE MODE
This mode reduces toner consumption, increasing cost effective-
ness, with only a slight loss in copy density. Follow the procedure
below for setting the toning level.
1
Press the EXPOSURE key to select the PHOTO mode.
2
Open the front cover.
3
Press and hold the EXPOSURE key for more than 3
seconds.
lThe exposure indicator marked Ò3Ó will light up, indicating that
the standard toner mode is active.
4
To enter the toner save mode, press the LIGHT key.
lThe...

22
STATUS INDICATORS
When a misfeed occurs, the copier will stop.
The misfeed (
) indicator will blink and blinking
red misfeed location indicators will indicate the
approximate misfeed location.If paper becomes accidentally torn during removal,
be sure to remove all pieces. Be careful not to
damage the photoconductive drum or the corona
wires.
First confirm the misfeed locations.
For misfeeds in optional equipment, see the cor-
responding sections of this manual.
Misfeed in the manual feed tray
1
Gently...

23
STATUS INDICATORS
MISFEED REMOVAL
 Misfeed removal
Misfeed in a paper tray
1
Open the side cover.
NOTE:
If the transport area misfeed indicator is lighted, clear the transport
area first. (See below, ÒMisfeed in the transport area.Ó)
2
Remove the misfed paper.
lBe careful not to tear the misfed paper during removal.
3
If the paper cannot be seen from the side, pull out the
paper tray and remove the misfed paper.
lBe careful not to tear the misfed paper during removal.
4
Close the paper tray and the...

24
STATUS INDICATORS
2
Turn the transport lever to the left.
3
Turn the roller rotating knob in the direction of the arrow
to remove the misfed paper.
4
Turn the transport lever back into place.
5
Close the front cover.
lConfirm that theindicator has gone out.
MISFEED REMOVAL
Misfeed around the fusing unit and exit area
1
Open the front cover.
 Misfeed removal
Transport lever
Roller rotating knob
Downloaded From ManualsPrinter.com Manuals 

25
STATUS INDICATORS
2
Turn the roller rotating knob in the direction of the arrow
and remove the paper from the fusing unit area.
CAUTION
The fusing unit is hot! Use care in removing paper.
3
If the misfed paper is in the exit area, open the exit area
cover carefully.
lOpen the cover by pulling the lever up. Support it until fully open.
lIf an optional sorter is installed, slide it away from the copier and
then open the cover.
4
Turn the roller rotating knob in the direction of the arrow
and remove the...

26
STATUS INDICATORS
MISFEED REMOVAL
Misfeed in the duplex module
lThe duplex module is optional.
NOTE:
If any other misfeed locations are indicated, be sure to remove any
misfed paper from these locations before performing the procedure
described below. If not, a sheet of paper in another location may
become torn and difficult to remove.
1
Pull out the duplex module.
2
Lift up the upper and lower paper guides, and remove
the misfed paper.
lWhen a misfeed occurs between the paper guides, open the
upper...

27
STATUS INDICATORS
1
Open the toner collecting container cover.
2
Disengage and remove the container from the copier by
pushing downward and then pulling it out.
lToner cannot be reused. Do not transfer used toner to the toner
hopper.
lRemove the cap from a new toner collecting container and use
it to cover the full toner collecting container.
lKeep the full toner collecting container until the next regular
service call. Your authorized Sharp Service Technician will
collect the container for disposal....

28
STATUS INDICATORS
When the developer replacement required () indicator lights up,
the developer should be replaced.
DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN
AUTHORIZED SHARP SERVICE TECHNICIAN. Contact your
Service Center as soon as possible.
NOTE:
If the
indicator and the copy quantity display blink simulta-
neously, contact your Service Center.
Developer required
DEVELOPER REQUIRED
Downloaded From ManualsPrinter.com Manuals