Sharp SF 2530 User Manual

29
STATUS INDICATORS
MAINTENANCE REQUIRED
When the maintenance required () indicator lights up, service by
an authorized Sharp Service Technician is required. Contact your
Service Center as soon as possible.
Maintenance required
Downloaded From ManualsPrinter.com Manuals 

30
GENERAL INFORMATION
PART NAMES AND FUNCTIONS
Exterior
qDocument holder
wExit tray
Finished copies are deposited in the exit tray.
eDocument cover (optional in some areas)
Place the original on the document glass and
close the document cover before copying starts.
rOperation panel
All copier controls are located here for easy
operation.
tDocument glass
Place the document to be copied here.
yPaper clip tray
Keep paper clips here.
uOriginal size detector
Detects the size of the original. Do not place...

31
GENERAL INFORMATION
PART NAMES AND FUNCTIONS
Interior
!8Fusing unit
The fusing unit is hot. Exercise care in this area.
!9Transport lever
Turn to open the transport section.
@0Corona unit
The unit is used to charge the photoconductive
drum.
@1Photoconductive drum
Copy images are formed on the photoconductive
drum.
@2Toner hopper
Contains toner.
@3Roller rotating knobs
Turn to remove misfed paper.
@4Toner hopper lock lever
Pull down to release the toner hopper.
@5Toner collecting container
Used toner...

32
GENERAL INFORMATION
qEDGE ERASE key and indicator (p.17)
Use to erase dark areas from copy edges.
wMARGIN SHIFT key and indicator (p.18)
Shifts text or image on the copy to leave a
binding margin on the left side of the copy.
eDUAL PAGE COPY key and indicator (p.16)
Makes individual copies of two originals placed
side by side on the document glass.
rEXPOSURE key and indicators (p. 9)
Press to select the exposure mode: AUTO,
MANUAL, or PHOTO.
tCOPY RATIO display
Displays the copy ratios for reductions...

33
GENERAL INFORMATION
PART NAMES AND FUNCTIONS
NOTE:11 x 17 sized copies are counted as
two copies.
#0Clear (
C) key
Press to clear the copy quantity display, or press
during a copy run to terminate copying. The
copier will stop after copies in progress are
finished.
#1CLEAR ALL (
) key
Clears all selected settings and returns the
copier to the initial settings.
#2START key and indicator
Copying is possible when the indicator is on.
Press to start copying.
#3POWER SAVE indicator (p. 43)
Lights up when...

34
GENERAL INFORMATION
USER PROGRAMS
The user programs allow the parameters of certain functions to be set,
changed, or cancelled as desired.
List of user programs
This copier has the following user programs.
Program No. Program name Description
1 Auto clear time Sets the auto clear time. The copier returns to the initial settings
when the auto clear time elapses after the last copy is made.
2 Preheat mode Sets the time that elapses before the copier enters the preheat
mode after any operation is made....

35
GENERAL INFORMATION
Setting the user programs
1
Press and hold the TRAY SELECT key for more than 5
seconds until all the alarm indicators* blink and ÒÐ ÐÓ
appears in the copy quantity display.
*The alarm indicators are the  , ,, ,  and
indicators.
2
Enter a program number using the 10-key pad.
lThe selected program number will blink in the copy quantity
display.
lIf a mistake is made in steps 2 to 4, press the clear (C) key.
You will return to step 2.
lThe program numbers are shown in the table...

36
GENERAL INFORMATION
USER PROGRAMS
4
Select the desired parameter using the 10-key pad.
lThe entered parameter number will blink on the right side of the
copy quantity display.
lThe parameters are shown in the table below.
For example, to change the setting of the auto power shut-off
timer to Ò30 min.Ó, press key 2.
Program name Parameters
Auto clear time 0 e OFF 1 e 30 sec.*2 e 60 sec.
3 e 90 sec. 4 e 120 sec.
Preheat mode 1 e 1 min.*2 e 15 min. 3 e 30 min.
4 e 60 min. 5 e 120 min. 6 e 150 min.
7 e...

37
GENERAL INFORMATION
Program No. Program name Description
10 Auditing mode Enables or disables the auditing mode, which controls access to
copier. See page 8.
11 Account number Registers accounts for auditing mode.
entry
12 Account number Changes account numbers for auditing mode.
change
13 Account number Deletes accounts for auditing mode.
deletion
14 Number of copies Displays the total number of copies made against account numbers.
per account
15 Resetting account Resets all audit accounts or resets...

38
GENERAL INFORMATION
3
Enter the number 16 using the 10-key pad and press the
START key.
4
Choose a new 3-digit code number and enter it using the
10-key pad.
5
Press the START key.
lThe code number will change from the previous setting to the
new setting.
lÒ  Ð Ð Ó will appear again in the copy ratio display.
6
To continue with other auditing programs, enter the
appropriate program code number.
To exit the auditing programs, press the CLEAR ALL
(
) key.
AUDITING PROGRAMS
Auditing programs
Setting for...