Sharp SF 2530 User Manual

   
 
 
 
·	GETTING STARTED
·	MAKING COPIES
·	
STATUS INDICATORS
·	GENERAL INFORMATION
·	OPTIONAL EQUIPMENT
  

2
8
22
30
53
PLAIN PAPER COPIER


OPERATION MANUAL

MODEL
SF-2530
Page
SF
-2530 PLAIN PAPER COPIER
Downloaded From ManualsPrinter.com Manuals 

§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§
§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§§
§§
The power switch positions are marked ÒIÓ to indicate power ÒONÓ and
Ò
Ó to indicate stand-by.
In the stand-by position, power is being supplied to a drying heater within
the optical system of the copier.
Caution:
For complete electrical disconnection, pull out the main plug.
The equipment should be installed near an accessible socket outlet for
easy disconnection.
FOR YOUR RECORDS ...
To protect...

1
CONTENTSPage
GETTING STARTED
lINSTALLATION REQUIREMENTS..................2lCAUTIONS....................................3lLOADING COPY PAPER......................4lADDING TONER............................6
GETTING STARTEDINTRODUCTION
The SF-2530 has been designed to give
high productivity while offering convenient
copying features. Its main features are:
lEasy operation,lAutomatic exposure control,lPHOTO mode copying,lConvenient functions such as DUAL
PAGE COPYING, EDGE ERASE,
MARGIN SHIFT, and
lPower...

2
GETTING STARTEDINSTALLATION REQUIREMENTS
To ensure safety and proper machine perfor mance, please note the
following before initial installation and whenever the machine is to be
relocated.
1. The copier should be installed near an accessible power outlet
for easy connection.
2. Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
3. Do not install the machine where it is:
ldamp or humid,...

3
GETTING STARTEDCAUTIONS
1. Do not touch the photoconductive drum. Scratches or
smudges on the drum will cause dirty copies.
2. The fusing unit is extremely hot.  Exercise care in this area.
3. Installation adjusters are provided on the optional stand/
500-sheet paper drawer or stand/1000-sheet paper drawer.
When moving the machine with the optional stand/500-sheet
paper drawer or stand/1000-sheet paper drawer, be sure
to raise the installation adjusters. After moving the machine,
lower the installation...

4
GETTING STARTED
The paper required () indicator will light up when
there is no copy paper in a selected paper feed station
or when a selected paper tray is not installed or is
improperly installed.
For best results, use only Sharp recommended paper.
The copy paper size for the 500-sheet paper drawer
and the optional stand/500-sheet paper drawer or
optional stand/1000-sheet paper drawer will be set by
Sharp service personnel according to your request
when you purchase the copier. If a different paper...

5
GETTING STARTEDChanging the lower paper trayÕs inner cassette
The lower paper tray can accommodate five different paper sizes. To
change the paper size, simply change the inner cassette. (The inner
cassettes are optional.)
1
Gently lift and pull out the lower paper tray.
2
Grasp the inner cassette tabs and remove the cassette.
3
Remove the cover of the inner cassette to be installed.
If the cassette is empty, fan the copy paper and place it
in the cassette.
lThe cassette holds 500 sheets of 20 lb. bond...

6
GETTING STARTED
1
Open the front cover.
2
Pull down the toner hopper lock lever and pull the toner
hopper out slowly until it stops.
3
Hold the toner cartridge vertically and vigorously shake
it up and down about 20 times to loosen the toner. This
will allow the toner to flow more easily into the toner
hopper.
Adding toner
GENUINE SUPPLIES
ADDING TONER
The toner required () indicator will light up when toner
concentration level in the developer unit is low. If copying is
continued while the
indicator...

7
GETTING STARTED
4
Place the new toner cartridge with the tabs in the
notches as shown.
5
Slide the toner cartridge along the guides over the toner
hopper.
6
Hold the toner cartridge with one hand while pulling on
the sealing tape to remove it.
7
Tap on the top of the toner cartridge 5 times to release
all toner into the toner hopper.
lIt will take about 30 seconds for the toner to flow into the toner
hopper. Do not remove the toner cartridge until it is empty.
8
Slide the empty toner cartridge back...

8
MAKING COPIES
Auditing accounts
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not
function until an assigned 3-digit account number has been entered.
See page 37 for setting the auditing mode.
If the copier has been programmed in the auditing mode,  ÒÐÐÓ will
appear in the copy quantity display in the initial conditions.
1
Enter your account number using the 10-key pad.
lAs each digit is entered, the dashes in the copy quantity display
will disappear.
lAfter the...