Sharp SF 2530 User Manual

							19
MAKING COPIES
Interrupt
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
lReduction/enlargement/zoom, exposure adjustments, dual page
copying, edge erase, and margin shift can be selected during
interrupt copying.
lDuplex copying, sort, group, and staple sort cannot be selected
during interrupt copying.
lINTERRUPT will not function during duplex copying or when an
optional auditor (SF-EA12) is used and the copier has been
programmed in the auditing mode.
Interrupting a copy run
1
Press the INTERRUPT key.
lThe copier will return to the initial settings.
lIf this copier has been programmed in the auditing mode using
auditing program No.10, ÒÐ Ð Ó will appear in the copy quantity
display. Enter your account number using the 10-key pad. The
number of copies of the interrupt copying will be accumulated
against this account number. See page 8.
lWhen an optional document feeder (ADF or RADF) is being
used, the copier will stop after completing the copying of the
originals which have been fed into the document feeder.
2
When the copier stops, remove the original(s) and place
the original for interrupt copying on the document
glass. Close the document cover.
lIf an optional document feeder (ADF or RADF) is installed, place
the originals face up in the document feeder tray.
3
Select the desired available copier functions.
4
Press the START key.
5
When the interrupt copy run is complete, press the
INTERRUPT key again to cancel the mode and remove
the original(s) used for interrupt  copying.
lThe copier will reset itself to the functions which were in use
before the INTERRUPT key was first pressed.
6
Replace the original(s) for the interrupted job and press
the START key to resume copying.
INTERRUPT
CLEAR ALL
9
START
INTERRUPT
CLEAR ALL
Downloaded From ManualsPrinter.com Manuals 
						

							20
MAKING COPIES
Automatic exposure adjustment
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying
needs.
1
Ensure that the copier is in the AUTO exposure mode.
2
Open the front cover.
3
Press and hold the EXPOSURE key for more than 3
seconds.
lOne or two exposure indicators corresponding to the automatic
exposure level which has been selected will light up. The factory
default setting is level Ò3Ó.
4
Press the LIGHT or DARK key to lighten or darken the
automatic exposure level as desired.
5
Close the front cover.
lThis automatic exposure level will remain in effect until you
change it again by this procedure.
IGINAL TO COPY
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
EXPOSURE
AUTO
MANUAL
PHOTO
12345
AU
IGINAL TO COPY
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
EXPOSURE
AUTO
MANUAL
PHOTO
12345
AU
T
LIGHTDARK
12345
Downloaded From ManualsPrinter.com Manuals 
						

							21
MAKING COPIES
Toner save mode
TONER SAVE MODE
This mode reduces toner consumption, increasing cost effective-
ness, with only a slight loss in copy density. Follow the procedure
below for setting the toning level.
1
Press the EXPOSURE key to select the PHOTO mode.
2
Open the front cover.
3
Press and hold the EXPOSURE key for more than 3
seconds.
lThe exposure indicator marked Ò3Ó will light up, indicating that
the standard toner mode is active.
4
To enter the toner save mode, press the LIGHT key.
lThe exposure indicator marked Ò1Ó will light up, indicating that
the toner save mode is selected.
5
Close the front cover and press the EXPOSURE key to
select the desired exposure mode.
lTo return to the standard mode, repeat the procedure but use
the DARK key to select exposure level Ò3Ó in step 4.
IGINAL TO COPY
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
EXPOSURE
AUTO
MANUAL
PHOTO
12345
AU
IGINAL TO COPY
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
EXPOSURE
AUTO
MANUAL
PHOTO
12345
AU
T
LIGHTDARK
12345
Downloaded From ManualsPrinter.com Manuals 
						

							22
STATUS INDICATORS
When a misfeed occurs, the copier will stop.
The misfeed (
) indicator will blink and blinking
red misfeed location indicators will indicate the
approximate misfeed location.If paper becomes accidentally torn during removal,
be sure to remove all pieces. Be careful not to
damage the photoconductive drum or the corona
wires.
First confirm the misfeed locations.
For misfeeds in optional equipment, see the cor-
responding sections of this manual.
Misfeed in the manual feed tray
1
Gently pull the misfed paper out.
2
Open and close the front cover to cancel the indicator.
 Misfeed removal
MISFEED REMOVAL
Fusing unit and exit area (   P. 24)
Optional duplex module (
   P. 26)Optional document feed area (
   P. 60)
Transport area (
   P. 23)
Paper feed area (
   P. 22, 23)
(manual feed tray and paper tray)
Paper feed area (
   P. 23)
(paper tray)
Paper feed area (
   P. 84)
(optional stand/500-sheet paper drawer 
 or stand/1000-sheet paper drawer) Optional sorter (
   P. 64, 79)
Downloaded From ManualsPrinter.com Manuals 
						

							23
STATUS INDICATORS
MISFEED REMOVAL
 Misfeed removal
Misfeed in a paper tray
1
Open the side cover.
NOTE:
If the transport area misfeed indicator is lighted, clear the transport
area first. (See below, ÒMisfeed in the transport area.Ó)
2
Remove the misfed paper.
lBe careful not to tear the misfed paper during removal.
3
If the paper cannot be seen from the side, pull out the
paper tray and remove the misfed paper.
lBe careful not to tear the misfed paper during removal.
4
Close the paper tray and the side cover.
lConfirm that theindicator has gone out.
Misfeed in the transport area
1
Open the front cover.
Downloaded From ManualsPrinter.com Manuals 
						

							24
STATUS INDICATORS
2
Turn the transport lever to the left.
3
Turn the roller rotating knob in the direction of the arrow
to remove the misfed paper.
4
Turn the transport lever back into place.
5
Close the front cover.
lConfirm that theindicator has gone out.
MISFEED REMOVAL
Misfeed around the fusing unit and exit area
1
Open the front cover.
 Misfeed removal
Transport lever
Roller rotating knob
Downloaded From ManualsPrinter.com Manuals 
						

							25
STATUS INDICATORS
2
Turn the roller rotating knob in the direction of the arrow
and remove the paper from the fusing unit area.
CAUTION
The fusing unit is hot! Use care in removing paper.
3
If the misfed paper is in the exit area, open the exit area
cover carefully.
lOpen the cover by pulling the lever up. Support it until fully open.
lIf an optional sorter is installed, slide it away from the copier and
then open the cover.
4
Turn the roller rotating knob in the direction of the arrow
and remove the paper.
lIf the misfed paper is deep in the fusing unit, lift the fusing unit
tab and remove any misfed paper.
CAUTION
The fusing unit is hot! Be sure to touch only the green tab or the
green roller rotating knob.
5
Close the exit area cover.
6
Close the front cover.
lConfirm that theindicator has gone out.
MISFEED REMOVAL
 Misfeed removal
Roller rotating knob
Exit area cover
Roller rotating knob
Fusing unit tab
Downloaded From ManualsPrinter.com Manuals 
						

							26
STATUS INDICATORS
MISFEED REMOVAL
Misfeed in the duplex module
lThe duplex module is optional.
NOTE:
If any other misfeed locations are indicated, be sure to remove any
misfed paper from these locations before performing the procedure
described below. If not, a sheet of paper in another location may
become torn and difficult to remove.
1
Pull out the duplex module.
2
Lift up the upper and lower paper guides, and remove
the misfed paper.
lWhen a misfeed occurs between the paper guides, open the
upper paper guide and remove the misfed paper.
3
Close the paper guides and push back the duplex
module.
lConfirm that theindicator has gone out.
 Misfeed removal
Paper guides
Upper paper guide
Downloaded From ManualsPrinter.com Manuals 
						

							27
STATUS INDICATORS
1
Open the toner collecting container cover.
2
Disengage and remove the container from the copier by
pushing downward and then pulling it out.
lToner cannot be reused. Do not transfer used toner to the toner
hopper.
lRemove the cap from a new toner collecting container and use
it to cover the full toner collecting container.
lKeep the full toner collecting container until the next regular
service call. Your authorized Sharp Service Technician will
collect the container for disposal.
3
Install the new toner collecting container by pushing it
down onto the spring-loaded tray and then allowing it to
move upward and click into place.
4
Close the toner collecting container cover.
 Used toner disposal
           USED TONER DISPOSAL
The toner collecting container full () indicator will blink when the
toner collecting container is full.
The copier will stop and will not operate until a new toner collecting
container has been installed. Replace the toner collecting container
as described below.
Downloaded From ManualsPrinter.com Manuals 
						

							28
STATUS INDICATORS
When the developer replacement required () indicator lights up,
the developer should be replaced.
DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN
AUTHORIZED SHARP SERVICE TECHNICIAN. Contact your
Service Center as soon as possible.
NOTE:
If the
indicator and the copy quantity display blink simulta-
neously, contact your Service Center.
Developer required
DEVELOPER REQUIRED
Downloaded From ManualsPrinter.com Manuals