Sharp SF 2530 User Manual

							69
OPTIONAL EQUIPMENT
Max. No. Max. No.
Mode Paper sizeof of copies
originals to be set
Min.:
NON- 5-1/2 x 8-1/2
Ð99
SORT Max.:
11 x 17
SORT/5-1/2 x 8-1/2,
STAPLE8-1/2 x 11, 30
SORT8-1/2 x 11R10
8-1/2 x 14, 11 x 17 15
5-1/2 x 8-1/2,
GROUP8-1/2 x 11,
1020
8-1/2 x 11R
8-1/2 x 14, 11 x 1715
Max. No. Max. No.
Mode Paper sizeof of copies
originals to be set
NON- Min.: 5-1/2 x 8-1/2
99
SORT Max.: 11 x 17Ð
SORT 5-1/2 x 8-1/2,
8-1/2 x 11, 50
8-1/2 x 11R 20
8-1/2 x 14, 11 x 17 25
8-1/2 x 11,
STAPLE 8-1/2 x 11R50
20
SORT
8-1/2 x 14, 11 x 17 25
5-1/2 x 8-1/2,
30
8-1/2 x 11
GROUP 20
8-1/2 x 11R,
25
8-1/2 x 14, 11 x 17
10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56)
Sort bins
SORT or
STAPLE SORT mode:
Paper sizeBin capacity
(max.)
5-1/2 x 8-1/2,
8-1/2 x 11, 30
8-1/2 x 11R
8-1/2 x 14,
15
11 x 17
GROUP mode:
Paper sizeBin capacity
(max.)
5-1/2 x 8-1/2,
8-1/2 x 11,20
8-1/2 x 11R
8-1/2 x 14,
15
11 x 17
SF-S54N SF-S56
NOTES:
lIf the specified number of copies is more than the maximum number of copies that can be set, the copy quantity
display will change to the corresponding number in the above table in the SORT, STAPLE SORT, or GROUP
mode after copying starts.
lWhen making single-sided copies from two-sided originals, the maximum number of originals that can be copied
is half the number shown in the above table.
lIf the sorter bin capacity control is enabled, the copier will stop when the number of originals exceeds the
maximum number in the SORT or STAPLE SORT mode. If the sorter bin capacity control is canceled using user
program No. 6, the copier will continue copying even if the number of originals exceeds the maximum number in
the SORT or STAPLE SORT mode, though copies will not be stapled.
lDo not use special paper in the SORT, STAPLE SORT, or GROUP mode.
10-bin staple sorter (SF-S54N)
20-bin staple sorter (SF-S56)
Sort bins
SORT mode:
Paper sizeBin capacity
(max.)
5-1/2 x 8-1/2,
8-1/2 x 11, 50
8-1/2 x 11R
8-1/2 x 14,
25
11 x 17
STAPLE SORT mode:
Paper sizeBin capacity
(max.)
8-1/2 x 11,
50
8-1/2 x 11R
8-1/2 x 14,
25
11 x 17
GROUP mode:
Paper sizeBin capacity
(max.)
5-1/2 x 8-1/2,
8-1/2 x 11,30
8-1/2 x 11R,
8-1/2 x 14, 25
11 x 17
The limits for the number of originals which can be used and the number of copies that can be set for each
paper size are as follows:
SORTER CAPACITIES
SF-S54N SF-S56
Top bin
Top bin 100 sheets in the NON-SORT mode
100 sheets in the NON-SORT mode (60 sheets for 8-1/2 x 14 and 11 x 17)
Downloaded From ManualsPrinter.com Manuals 
						

							70
OPTIONAL EQUIPMENT
Stapling location
10-bin staple sorter (SF-S54N)
20-bin staple sorter (SF-S56)
Staple sort
The STAPLE SORT mode staples copies of 5-1/2 x 8-1/2, 8-1/2 x
11, 8-1/2 x 11R, 8-1/2 x 14, and 11 x 17 sizes (SF-S54N) or
copies of 8-1/2 x 11, 8-1/2 x 11R, 8-1/2 x 14, and 11 x 17 sizes
(SF-S56).
Using the document glass
1
Set the original on the document glass with the corner
to be stapled to the upper right.
lCopy from the last page to the first page.
SF-S54N
lIf the number of copies to be delivered into each bin is more than
30 for 5-1/2 x 8-1/2, 8-1/2 x 11 or 8-1/2 x 11R paper or 15
for 8-1/2 x 14 or 11 x 17 paper, the copies will not be stapled.
SF-S56
 
lIf the number of copies to be delivered into each bin is more than
50 for 8-1/2 x 11 or 8-1/2 x 11R paper or 25 for 8-1/2 x 14
or 11 x 17 paper, the copies will not be stapled.
2
Press the SORTER key to select the STAPLE SORT
mode.
lMake sure that there is no paper in any sort bin before selecting
the STAPLE SORT mode.
3
Set the number of copies.
lUp to 10 sets (SF-S54N) or 20 sets (SF-S56) can be made.
4
Press the START key.
5
When all copies are made and sorted, press the manual
staple key.
lEach set of copies will be stapled.
lSets of copies containing copies of different width will not be
stapled.
10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56)
(ORIGINALS)EVEN NUMBE
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
POWER SAVE
START
1
23
456
7
0
C 8
9
SF-S54N
SF-S56
Downloaded From ManualsPrinter.com Manuals 
						

							71
OPTIONAL EQUIPMENT
(ORIGINALS)EVEN NUMBE
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
9
START
Using the ADF or RADF
1
Set the originals in the document feeder tray face up
with the stapling position in the upper left corner.
SF-S54N
lIf the number of copies to be delivered into each bin is more than
30 for 5-1/2 x 8-1/2, 8-1/2 x 11 or 8-1/2 x 11R paper or 15
for 8-1/2 x 14 or 11 x 17 paper, the copies will not be stapled.
SF-S56
lIf the number of copies to be delivered into each bin is more than
50 for 8-1/2 x 11 or 8-1/2 x 11R paper or 25 for 8-1/2 x 14
or 11 x 17 paper, the copies will not be stapled.
2
Press the SORTER key to select the STAPLE SORT
mode.
lMake sure that there is no paper in any sort bin before selecting
the STAPLE SORT mode.
3
Set the number of copies.
lUp to 10 sets (SF-S54N) or 20 sets (SF-S56) can be made.
4
Press the START key.
lWhen copying and sorting are completed, each set of copies will
be automatically stapled.
lSets of copies containing copies of different width will not be
stapled.
10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56)
10-bin staple sorter (SF-S54N)
20-bin staple sorter (SF-S56)
Stapling location
1
23
456
7
0
C 8
9
LECT
Downloaded From ManualsPrinter.com Manuals 
						

							72
OPTIONAL EQUIPMENT
1
Align the edges of the copies to be stapled.
2
Place the set of copies into the top bin, making sure the
edges are flush with the inner right corner, as shown in
the figure.
lMake sure that there is no paper in the other sort bins. If there
is, the manual staple key will not light up.
lUp to 50 sheets of paper can be stapled together. Exceeding this
maximum may result in damage to the stapler.
3
Press the manual staple key when it lights up.
lThe set of copies will be stapled.
Manual stapling (SF-S56 only)
To use the stapling feature only, without using the STAPLE SORT
mode, follow the procedure below.
Stapling location
Copies
20-bin staple sorter (SF-S56)
20-BIN STAPLE SORTER (SF-S56)
Downloaded From ManualsPrinter.com Manuals 
						

							73
OPTIONAL EQUIPMENT
STAPLE TEAR line
Staple cartridge replacement
The CHECK STAPLER indicator will blink when the staple cartridge
is empty and the copier is in the STAPLE SORT mode. Replace the
staple cartridge as follows.
lIf there are still many staples left, then staples have jammed in the
stapler. See page 76.
SF-S54N 10-bin staple sorter
1
Open the stapler cover.
2
Lifting the green release lever, remove the staple
cartridge from the stapler.
lA few staples will be left in the cartridge. Remove and discard
them.
3
Check that the first staple in the new cartridge is at the
tip of the cartridge.
lIf the first staple is not at the tip, pull it to the tip. If any staples
are protruding past the cartridge tip, tear them off at the STAPLE
TEAR line and align the first staple with the tip.
lA cartridge holds 5,000 staples.
4
Push the new staple cartridge in until it clicks in place.
5
Close the stapler cover.
lThe stapler feeds staples automatically.
lTo check that the stapler works properly, copy an original and
staple it.
10-BIN STAPLE SORTER (SF-S54N)
10-bin staple sorter (SF-S54N)
Downloaded From ManualsPrinter.com Manuals 
						

							74
OPTIONAL EQUIPMENT
SF-S56 20-bin staple sorter
1
Open the stapler cover.
2
Lift the release lever and pull out the staple box.
lLift the release lever to unlock the staple box. Then pull out the
box.
3
Remove the empty staple cartridge from inside the
staple box.
4
Insert the new staple cartridge into the box until it clicks
in place.
lInsert the new cartridge by aligning the arrows on the cartridge
with those on the box. Check that the cartridge locks in place
by pulling it slightly.
lA cartridge holds 5,000 staples.
NOTE:
Be sure not to remove the rear paper and tape before inserting the
cartridge.
20-bin staple sorter (SF-S56)
20-BIN STAPLE SORTER (SF-S56)
Downloaded From ManualsPrinter.com Manuals 
						

							75
OPTIONAL EQUIPMENT
5
Remove the rear paper and tape from the cartridge.
lPull them straight. If they are pulled obliquely, the tape may be
torn.
6
Insert the staple box into the stapler until it clicks in
place.
7
Close the stapler cover.
8
Place a sheet of paper into the top bin. Press the manual
staple (
) key on the staple sorter when it lights up.
lCheck to see whether the sheet is stapled.
If it is not stapled, press the manual staple key again.
lIf the stapler does not operate properly even after replacement,
a staple may be jammed in it. See page 77.
lStaples for the staple sorter are available from your Sharp
dealer.
20-BIN STAPLE SORTER (SF-S56)
20-bin staple sorter (SF-S56)
Downloaded From ManualsPrinter.com Manuals 
						

							76
OPTIONAL EQUIPMENT
Staple jam removal
If staples become jammed in the stapler, the CHECK STAPLER
indicator and the STAPLE SORT mode indicator will blink. Remove
the jammed staples in the manner described below.
SF-S54N 10-bin staple sorter
1
Open the stapler cover.
2
Close the stapler cover.
lJammed staples will be removed automatically.
3
Remove all copies from the bins of the staple sorter.
lTo check that the stapler works properly, copy an original and
staple it.
10-bin staple sorter (SF-S54N)
10-BIN STAPLE SORTER (SF-S54N)
Downloaded From ManualsPrinter.com Manuals 
						

							77
OPTIONAL EQUIPMENT
SF-S56 20-bin staple sorter
1
Open the stapler cover.
2
Lift the release lever and pull out the staple box.
lLift the release lever to unlock the staple box. Then pull out the
box.
3
Lower the lever at the end of the staple box and remove
the jammed staples.
4
Return the lever to its original position.
20-BIN STAPLE SORTER (SF-S56)
20-bin staple sorter (SF-S56)
Downloaded From ManualsPrinter.com Manuals 
						

							78
OPTIONAL EQUIPMENT
5
Insert the staple box into the stapler unit until it clicks in
place.
6
Close the stapler cover.
7
Following the stapling procedure on page 72, staple a
copy to check that the stapler works properly.
lIf it does not, repeat this procedure until it does.
20-bin staple sorter (SF-S56)
20-BIN STAPLE SORTER (SF-S56)
Downloaded From ManualsPrinter.com Manuals