Sharp SF 2530 User Manual

							59
ADF (SF-A17)/RADF (SF-A56)
ADF (SF-A17)/RADF (SF-A56)
OPTIONAL EQUIPMENT
3
Enter the desired number of copies.
lThe maximum number of copies in the two-sided copy mode is
50 for 8-1/2 x 11 and 8-1/2 x 11R and 30 for 8-1/2 x 14 and
11 x 17 paper. If the specified number of copies exceeds the
above number, the copy quantity display will display the maximum
allowable number after copying starts. If an optional sorter is
installed, the display will change to 10 (SF-S18 and SF-S54N)
or 20 (SF-S15 and SF-S56) after copying starts (in sort mode).
4
Press the START key.
lTo cancel a copy run during duplex copying, press the CLEAR
ALL (
) key. Manually remove any copies remaining in the
duplex module following the procedure for removing misfed
paper from the duplex module. (See page 26.)
1-sided copies from 2-sided originals (SF-A56 only)
1
Adjust the original guides to the size of the originals and
set the originals face up in the document feeder tray.
2
Use the ORIGINAL TO COPY key to select .
3
Enter the desired number of copies.
4
Press the START key.
lTo cancel a copy run, press the CLEAR ALL () key. Copying
will stop and the RADF will output any originals which have been
fed. Also, the number in the copy quantity display will be reset
to 0.
POWER SAVE
START
1
23
456
7
0
C 8
9
PRE-COUNT
ORIGINALS APLE
RT
OUP
LIG
12
POWER SAVE
START
1
23
456
7
0
C 8
9
Downloaded From ManualsPrinter.com Manuals 
						

							60
ADF (SF-A17)/RADF (SF-A56)
OPTIONAL EQUIPMENT
ADF (SF-A17)/RADF (SF-A56)
Misfeed removal
Location C Location BLocation A
An original misfeed may occur at one of three locations:
(A) in the feed section, (B) in the exit roller, or (C) under
the transport belt.
(A) Open the feeding roller cover and pull the original gently
to the right and out from the document feeder tray.
lBe sure to open and close the document feeder cover to cancel
the misfeed location indicator.
(B) SF-A17: Gently pull the original out.
SF-A56: Open the exit roller cover and gently pull the
original out.
lBe sure to open and close the document feeder cover to cancel
the misfeed location indicator.
(C) Open the feeding roller cover, open the document feeder
cover, and remove the original.
NOTE:
After misfed originals are removed from locations A, B, and/or C,
a number may appear in the copy quantity display, indicating the
number of originals which must be returned to the document feeder
tray. Return the originals and press the START key to resume
copying.
AC B
Feeding roller cover
Exit roller coverSF-A17
SF-A56
Downloaded From ManualsPrinter.com Manuals 
						

							61
OPTIONAL EQUIPMENT
10-BIN SORTER (
SF-S18)
20-BIN SORTER (
SF-S15)
There are two sorter modes for different copying jobs: one sorts
copies into sets matching the sequence of originals and the second
groups copies from different originals into separate sort bins.
The maximum allowable number of copies varies with the selected
mode.
The number of copies will be automatically reset to the maximum
number allowable for the selected mode when copying begins if this
maximum is exceeded.
NOTES:
lTo install the 20-bin sorter (SF-S15), an optional stand/500-sheet
paper drawer (SF-D20), stand/1000-sheet paper drawer (SF-D21)
or an equivalent stand must be installed.
lThe bin intervals of the 10-bin sorter (SF-S18) are narrow for space
conservation. When copying from an optional document feeder
(ADF or RADF) is completed or the CLEAR ALL (
) or the sorter
bin access key is pressed in the document glass mode, the bins will
move three at a time and the space between them will become
larger so that copies can be easily taken out. This bin access mode
can be disabled using user program No. 7. See page 34, USER
PROGRAMS.
CAUTION
Do not put pressure on the sorter or subject it to undue force.
PART NAMES
SF-S18 SF-S15
10-bin sorter (SF-S18)
20-bin sorter (SF-S15)
Top cover
Sort bins
Sort bins
Bin access key
Sorter lock lever
Downloaded From ManualsPrinter.com Manuals 
						

							62
OPTIONAL EQUIPMENT
10-BIN SORTER (SF-S18)/ 20-BIN SORTER (SF-S15)
GROUP SORT
Using a sorter
10-bin sorter (SF-S18)
20-bin sorter (SF-S15)
Press the SORTER key to select the desired mode.
(The STAPLE SORT mode cannot be selected for either the
SF-S18 or SF-S15.)
To cancel the mode, press the SORTER key until the SORT and
GROUP indicators go out.
NON-SORT
When neither of the two available sorter modes, SORT or GROUP is
selected, the copier is in the NON-SORT mode. In this mode, all
copies will be deposited in the top bin of the sorter.
Be sure to use the NON-SORT mode when copying onto special
papers such as transparency film or label stock.
SORT
Press the SORTER key to select the SORT mode.
SORT is used for automatic copy collating. Copies of each original will
be sequentially deposited in the sort bins.
GROUP
Press the SORTER key to select the GROUP mode.
In the GROUP mode, all copies of the same original will be deposited
in the same bin.
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
EXPOSURE
AUTO
MANUAL
PHOTO
LIGHTDARK
1234
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
EXPOSURE
AUTO
MANUAL
PHOTO
LIGHTDARK
1234
(ORIGINALS)EVEN NUMBER
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
EXPOSURE
AUTO
MANUAL
PHOTO
LIGHTDARK
1234
Downloaded From ManualsPrinter.com Manuals 
						

							63
OPTIONAL EQUIPMENT
SORTER CAPACITIES
SF-S18 SF-S15
Top bin Top bin
100 sheets in the NON-SORT mode 100 sheets in the NON-SORT mode
Sort bins
SORT mode:
Paper sizeBin capacity
(
max.)
5-1/2 x 8-1/2,
8-1/2 x 11, 30
8-1/2 x 11R
8-1/2 x 14,
15
11 x 17
GROUP mode:
Paper sizeBin capacity
(
max.)
5-1/2 x 8-1/2,
8-1/2 x 11,20
8-1/2 x 11R
8-1/2 x 14, 15
11 x 17
The limits for the number of originals which can be used and the number of copies that can be set for each
paper size are as follows:
SF-S15
Max. No. Max. No.
Mode Paper size of of copies
originals to be set
Min.:
NON- 5-1/2 x 8-1/2
Ð99
SORT Max.:
11 x 17
SORT 8-1/2 x 11, 50 20
8-1/2 x 11R,
8-1/2 x 14,
GROUP 11 x 17 20 30
10-BIN SORTER (SF-S18)/ 20-BIN SORTER (SF-S15)
Sort bins:
Up to 50 per bin in the SORT mode
Up to 30 per bin in the GROUP mode
NOTES:
lIf the specified number of copies is more than the maximum number of copies that can be set, the copy quantity
display will change to the corresponding number in the above table in the SORT or GROUP mode after copying
starts.
lWhen making single-sided copies from two-sided originals, the maximum number of originals that can be copied
is half the number shown in the above table.
lDo not use special paper in the SORT or GROUP mode.
SF-S18
Max. No. Max. No.
Mode Paper size of of copies
originals to be set
Min.:
NON- 5-1/2 x 8-1/2
Ð99
SORT Max.:
11 x 17
5-1/2 x 8-1/2,
8-1/2 x 11,
30
8-1/2 x 11R
10
SORT
8-1/2 x 14,
15
11 x 17
5-1/2 x 8-1/2,
20
8-1/2 x 11,
10 GROUP
8-1/2 x 11R
8-1/2 x 14,
15
11 x 17
10-bin sorter (SF-S18)
20-bin sorter (SF-S15)
Downloaded From ManualsPrinter.com Manuals 
						

							64
OPTIONAL EQUIPMENT
Misfeed removal
The copier will stop when a misfeed occurs. The misfeed ()
indicator will blink and blinking red misfeed location indicators will
indicate the approximate misfeed location.
SF-S18 10-bin sorter
1
Pull the sorter lock lever and carefully slide the sorter
away from the copier.
2
Remove the misfed paper from the sorter or from the exit
area of the copier.
3
Slide the sorter back toward the copier and latch it into
place.
lConfirm that theindicator has gone out.
lIf theindicator is still blinking, check the inside of the copier
and remove any remaining misfed paper.
10-BIN SORTER (SF-S18)
10-bin sorter (SF-S18)
Downloaded From ManualsPrinter.com Manuals 
						

							65
OPTIONAL EQUIPMENT
20-BIN SORTER (SF-S15)
20-bin sorter (SF-S15)
SF-S15  20-bin sorter
1
Open the top cover and remove the misfed paper.
2
Close the top cover.
lConfirm that theindicator has gone out.
3
If theindicator is still blinking or the misfed paper
cannot be seen from the top, slide the sorter carefully
away from the copier.
4
Open the side cover and remove any misfed paper.
5
Close the side cover and push the sorter back against
the copier.
lConfirm that theindicator has gone out.
lIf theindicator is still blinking, check the inside of the copier
and remove any remaining misfed paper.
Downloaded From ManualsPrinter.com Manuals 
						

							66
OPTIONAL EQUIPMENT
SF-S15
No. of bins 20
Bin capacity NON-SORT: 100 sheets (top bin)
SORT: 50 sheets
GROUP: 30 sheets
Paper size Top bin: Max. 11 x 17
Min. 5-1/2 x 8-1/2
Sort bins: Max. 11 x 17
Min. 8-1/2 x 11
Power supply Drawn from the copier
Weight Approx. 68.4 lbs. (31 kg)
Dimensions 19-11/16 (W) x 20-31/64 (D) x 37-11/16 (H)
(500 mm (W) x 520 mm (D) x 957 mm (H))
Specifications are subject to change for improvement without notice.
10-BIN SORTER (SF-S18)/ 20-BIN SORTER (SF-S15)
Specifications
SF-S18
No. of bins 10
Bin capacity NON-SORT: 100 sheets (top bin)
SORT: 30 sheets (5-1/2 x 8-1/2, 8-1/2 x 11,
8-1/2 x 11R)
15 sheets (8-1/2 x 14, 11 x 17,
GROUP: 20 sheets (5-1/2 x 8-1/2, 8-1/2 x 11,
8-1/2 x 11R))
15 sheets (8-1/2 x 14, 11 x 17)
Paper size Max. 11 x 17
Min. 5-1/2 x 8-1/2
Power supply Drawn from the copier
Weight Approx. 15.5 lbs. (7 kg)
Dimensions 13-13/64 (W) x 19-27/64 (D) x 11-47/64 (H)
(335 mm (W) x 493 mm (D) x 298 mm (H))
10-bin sorter (SF-S18)
20-bin sorter (SF-S15)
Downloaded From ManualsPrinter.com Manuals 
						

							67
OPTIONAL EQUIPMENT
PART NAMES
SF-S54N
SF-S56
10-bin staple sorter (SF-S54N)
20-bin staple sorter (SF-S56)
10-BIN STAPLE SORTER (
SF-S54N)
20-BIN STAPLE SORTER (
SF-S56)
There are two sorter modes for different copying jobs:
one sorts copies into sets matching the sequence of the
originals and the second groups copies from different
originals into separate sort bins.
The SF-S54N 10-Bin Staple Sorter and the SF-S56 20-
Bin Staple Sorter have, in addition to the above two
modes, a STAPLE SORT mode. Sorted copies can be
automatically stapled together.
The maximum allowable number of copies varies with
the selected mode.
The number of copies will be automatically reset to the
maximum number allowable for the selected mode
when copying begins if this maximum is exceeded.NOTES:lTo install the 20-bin staple sorter (SF-S56), an
optional stand/500-sheet paper drawer (SF-D20),
stand/1000-sheet paper drawer (SF-D21) or an
equivalent stand must be installed.
lThe bin intervals of staple sorter SF-S54N are narrow
for space conservation. When copying from an
optional ADF or RADF is completed or the clear all
(
) key or the sorter bin access key is pressed in
the document glass mode, the bins will move three
at a time and the space between them will become
larger so that copies can be easily taken out. This
sorter bin access mode can be disabled by user
program No. 7. See page 34, USER PROGRAMS.
Sort bins
Sorter lock lever
Stapler cover
Bin access 
keyManual staple 
key
BIN ACCESS
STAPLE
Sort bins
Staple required indicator
Manual staple key
Stapler cover
CAUTION
lDo not put pressure on the sorter or subject it to undue force.
lDo not place your hands on the sorter during copying because the sorter moves up and down (SF-S56).
Downloaded From ManualsPrinter.com Manuals 
						

							68
OPTIONAL EQUIPMENT
10-bin staple sorter (SF-S54N)
20-bin staple sorter (SF-S56)
10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56)
GROUP SORT
(ORIGINALS)EVEN NUMBE
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
(ORIGINALS)EVEN NUMBE
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
(ORIGINALS)EVEN NUMBE
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
(ORIGINALS)EVEN NUMBE
ODD NUMBER
PRE-COUNT
ORIGINALS SORT
STAPLE
SORT
GROUP
Using a sorter
Press the SORTER key to select the desired mode.
To cancel the mode, press the SORTER key until the SORT, STAPLE
SORT, and GROUP indicators all go out.
NON-SORT mode
When none of the three sorter modes, SORT, STAPLE SORT or
GROUP is selected, the copier is in the NON-SORT mode. In this
mode, all copies will be deposited in the top bin of the sorter.
Be sure to use the NON-SORT mode when copying onto special
papers such as transparency film or label stock.
SORT mode
Press the SORTER key to select the SORT mode.
SORT is used for automatic copy collating. Copies of each original are
sequentially deposited in the sort bins.
STAPLE SORT mode
Press the SORTER key to select the STAPLE SORT mode.
In this mode, copies will be automatically sorted and finished sets of
copies can be stapled with the manual staple key. When used in
conjunction with an optional document feeder (ADF or RADF), sorted
copies will be automatically stapled.
GROUP mode
Press the SORTER key to select the GROUP mode.
In the GROUP mode, all copies of the same original are deposited in
the same bin.
Downloaded From ManualsPrinter.com Manuals