Sharp Mxm264n User Guide

7-69
SYSTEM SETTINGS
Contents
Disabling of Devices
Use these settings when a peripheral device on the machine has failed or when you wish to temporarily disable a device.
Disabling of Document Feeder
(When the automatic document feeder is installed.)
Use this setting to prohibit the use of the automatic 
document feeder, such as when the feeder malfunctions. 
(When the setting is enabled, scanning is still possible 
using the document glass.)
Disabling of Duplex
This is used to disable two-sided...

7-70
SYSTEM SETTINGS
Contents
Copy Function Settings
The following settings are related to copying. Touch the [Copy Function Settings] key to configure the settings.
Default settings selected with these settings apply to all functions of the machine (not just the copy function).
Initial Status Settings
The copier settings are reset when the [POWER] key () is turned on, when the [CLEAR ALL] key () is pressed, or 
when the auto clear interval has elapsed. These settings are used to change the default...

7-71
SYSTEM SETTINGS
Contents
Other Settings
Copy Exposure Adjustment
This is used to adjust the exposure level when [Auto] is 
used for the copy exposure.
Use this for the document glass and for the automatic 
document feeder.
Rotation Copy Setting
When the original and paper are placed in different 
orientations, this function automatically rotates the image 
90 degrees to enable correct copying on the paper.
Add or Change Extra Preset Ratios
Two enlargement preset ratios (101% to 400%) and two...

7-72
SYSTEM SETTINGS
Contents
Disabling Deletion of Job Programs
This is used to prohibit the deletion and changing of copy 
settings stored in job programs.
Disabling of Bypass-Tray in 
Duplex Copy
This is used to prohibit the use of the bypass tray when 
making two-sided copies.
The bypass tray is often used to feed label sheets, 
transparency film, and other special media for which 
two-sided copying is prohibited. If a sheet of one of these 
special media enters the reversing unit, a misfeed or...

7-73
SYSTEM SETTINGS
Contents
Network Settings
Network settings are described below. Touch the [Network Settings] key to configure the settings.
IPv4 Settings
When using the machine on a TCP/IP (IPv4) network, use 
this setting to configure the IP address of the machine.
The settings are shown below.
IP Address
Enter the IP address of the machine.
IP Subnet Mask
Entry the IP Subnet Mask.
IP Gateway
Enter the IP Gateway address.
DHCP
Use this setting to have the IP address obtained 
automatically using...

7-74
SYSTEM SETTINGS
Contents
Printer Settings
Settings related to the printer function can be configured. Touch the [Printer Settings] key to configure the settings.
Default Settings
Printer condition settings are described below.
Prohibit Notice Page Printing
This setting is used to disable printing of notice pages.
Prohibit Test Page Printing
This setting is used to disable printing of test pages. 
When this setting is enabled, Printer Test Page in the 
system settings cannot be used to print test...

7-75
SYSTEM SETTINGS
Contents
Interface Settings
These settings are used to control and monitor data transmitted to the USB port or network port of the machine.
Hexadecimal Dump Mode
(When the hard disk drive is installed)
This function is used to print the print data from a computer 
in hexadecimal format together with the corresponding ASCII 
text. This allows you to check whether or not print data from 
the computer is being transmitted to the machine correctly.
Example of a hexadecimal dump
I/O...

7-76
SYSTEM SETTINGS
Contents
Image Send Settings
Settings related to the image send function (scan, Internet fax, etc.) can be configured. Touch the [Image Send Settings] 
key to configure the settings.
Operation Settings
The operation settings below apply to all image send functions.
Default Display Settings
You can select one of 5 base screen types for the base screen 
that appears when the [IMAGE SEND] key is touched or when 
the [CLEAR ALL] ( ) key is pressed in image send mode.
 Address Book...

7-77
SYSTEM SETTINGS
Contents
Must Input Next Address Key at 
Broadcast Setting
This setting is used to require that the [Next Address] 
key be touched before the next address is entered when 
performing a broadcast transmission.
When this setting is enabled, the [Next Address] key 
cannot be omitted even if the next address is entered 
with a one-touch key.
If a user attempts to enter the next address without 
touching the [Next Address] key, a double-beep alarm 
will sound and the entry will be...

7-78
SYSTEM SETTINGS
Contents
Disable Registration of Program
This prohibits the use of the address book when a 
program is stored.
Configure the setting for each of the following items:
E-mail
 FTP
 Desktop
Network Folder
 Internet Fax (Including Direct SMTP)
Fax
Select All: Select all items.
Clear Checked: Clear all selections.
Disable Registration of Memory 
Box
Disable all types of memory box registration.
Configure the setting for each of the following items:
Polling Memory, Confidential,...