Sharp Mxm264n User Guide

2-33
COPIER
Contents Staple sort function
The staple sort function sorts output into sets, staples each set, and delivers the sets to the tray.
The relations between the stapling positions, paper orientation, permitted paper sizes for stapling, and number of sheets 
that can be stapled are shown below.
For original placement orientations, see Original placement orientation (for the staple sort) (page 2-34).
* You can insert 2 sheets of maximum 200g/m2 as cover sheets and staple them. In such cases, you...

2-34
COPIER
Contents Original placement orientation (for the staple sort)
When using the staple sort function, the original must be placed as shown below to enable stapling in the desired 
position on the paper.
Staple sort
Document feeder trayDocument glass
One staple (top)
abcabc 

2-35
COPIER
Contents
MAKING COPIES USING THE BYPASS TRAY
In addition to plain paper, the bypass tray allows you to make copies on transparency film, envelopes, tab paper, and 
other special media.
For detailed information on paper that can be loaded in the bypass tray, see IMPORTANT POINTS ABOUT PAPER 
(page 1-28) in 1. BEFORE USING THE MACHINE. For precautions when loading paper in the bypass tray, see 
LOADING PAPER IN THE BYPASS TRAY (page 1-33) in 1. BEFORE USING THE MACHINE.
1
Place the original....

2-36
COPIER
Contents
4
Check the paper type setting for the 
bypass tray. If you need to change the 
setting, touch the paper type key.
If you do not need to change the paper size and type that 
appear under Bypass Tray, go to step 7.
5
Select the type of paper used in the 
bypass tray.
Select the paper type that you will use.
6
Set the paper size.
(1) Select the paper size.
[Auto-Inch] key
When the paper placed in the bypass tray is an inch size 
(8-1/2 x 11, etc.), the paper size will be detected...

2-37
COPIER
Contents
Enter the paper size of the bypass tray
When the [Custom Size] key is touched, the paper size entry screen appears.
Touch the X (width) numeric value display key to open a 
number entry screen. Enter the width of the paper with 
the numeric keys, and touch the [OK] key in the number 
entry screen.
Touch the Y (height) numeric value display key to open a 
number entry screen. Enter the height of the paper with 
the numeric keys, and touch the [OK] key in the number 
entry screen.
7...

2-38
COPIER
Contents
This chapter explains Margin Shift, Erase, Dual Page Copy, and other special modes.
SPECIAL MODES
When the [Special Modes] key is pressed in the base screen, the special modes menu screen appears. The special 
modes menu consists of two screens. Touch the 
 keys to move between the screens. After selecting special 
mode settings, touch the [OK] key in the special modes menu screen to complete the settings and return to the base 
screen of copy mode.
Special modes menu (1st screen)...

2-39
COPIER
Contents Special modes menu (2nd screen)
(1) [Stamp] key

PRINTING THE DATE AND A STAMP ON COPIES 
(Stamp) (page 2-80)
(2) [Image Edit] key

[Image Edit] KEY (page 2-100)
(3) [Sharpness] key

ADJUSTING THE SHARPNESS OF AN IMAGE 
(Sharpness) (page 2-109)
(4) [File] key
This saves a job in a folder of the document filing 
function. 
The hard disk drive is required.
(5) [Quick File] key
This saves a job in the Quick File folder of the document 
filing function. 
The hard disk drive is...

2-40
COPIER
Contents [OK] key and [Cancel] key
In some cases two [OK] keys and one [Cancel] key will appear in the special mode screens. The keys are used as 
follows:
(A) Enter the selected special mode settings and return to the base screen of copy mode.
(B) Enter the selected special mode settings and return to the special modes menu screen. Touch this key when you 
wish to continue selecting other special mode settings.
(C) During selection of special mode settings, this key returns you to the...

2-41
COPIER
Contents
ADDING MARGINS (Margin Shift)
This function is used to shift the copy image right, left or down to adjust the margin.
This is convenient when you wish to bind the copies with a string or in a binder.
Shifting the image to the right so the copies can be bound at the left edge with a string
Margin shift positions
11
Not using margin shiftUsing margin shift
The punch holes cut off 
part of the imageThe image is moved to 
allow space for the string 
holes so the image is not 
cut off....

2-42
COPIER
Contents
4
Press the [START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you 
have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then 
touch the [Read-End] key. 
To cancel scanning of the original and copying...
Press the [STOP] key ( ).
Rotation copy cannot be used in combination with margin shift.
To cancel the margin shift...