Sharp Mxm264n User Guide

2-13
COPIER
Contents
3
Set the number of copies (number of 
sets) with the numeric keys.
 Up to 999 copies (sets) can be set.
 A single copy can be made even if 0 appears for the number of copies.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
4
Press the [START] key.
To cancel scanning of the original and copying...
Press the [STOP] key ( ).
Plain
7
A4
Special Modes
2-Sided Copy 

2-14
COPIER
Contents
MAKING A COPY USING THE DOCUMENT GLASS
To make a copy of a book or other thick original that cannot be scanned with the automatic document feeder, open the 
automatic document feeder and place the original on the document glass. This section explains how to make a copy 
(1-sided copy of a 1-sided original) using the document glass.
1
Open the automatic document feeder, 
place the original face down on the 
document glass, and then gently close 
the automatic document feeder.
 Align...

2-15
COPIER
Contents
3
Set the number of copies (number of 
sets) with the numeric keys.
 Up to 999 copies (sets) can be set.
 A single copy can be made even if 0 appears for the number of copies.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
4
Press the [START] key.
Normally copying will start.
Depending on the copy settings (2-sided copying, etc.), copying may not begin until all originals have been scanned. In this 
case, go to the next...

2-16
COPIER
Contents
AUTOMATIC 2-SIDED COPYING
USING THE AUTOMATIC DOCUMENT FEEDER TO 
MAKE 2-SIDED COPIES
Copying onto both sides of a sheet saves paper.
Automatic 2-sided copying of 1-sided 
originalsAutomatic 2-sided copying of 2-sided 
originals1-sided copying of 2-sided originals
1
Place the originals face up in the 
document feeder tray with the edges 
aligned evenly.
Insert the originals all the way into the document feeder tray.
Multiple originals can be placed in the document feeder tray. 
The...

2-17
COPIER
Contents Using the [Binding Change] key
4
Check the paper to be used.
Make sure that the desired paper (tray) is selected.
 To change the paper (tray), touch the [Paper Select] key.

PAPER TRAYS (page 2-11)
Depending on the size of the placed original, there may be cases where the same size of paper as the original is not 
selected automatically. In this event, change the paper size manually.
5
Set the number of copies (number of 
sets) with the numeric keys.
 Up to 999 copies (sets) can be...

2-18
COPIER
Contents
AUTOMATIC 2-SIDED COPYING USING THE 
DOCUMENT GLASS
Automatic 2-sided copying of 1-sided 
originals
1
Open the automatic document feeder, 
place the original face down on the 
document glass, and then gently close 
the automatic document feeder.
 Align the corner of the original with the tip of the arrow mark 
 on the document glass scale.
 Place the original in the appropriate position for its size as 
shown above.
 After placing the original, be sure to close the automatic...

2-19
COPIER
Contents
3
Select the 2-sided copy mode.
(1) Touch the [1-Sided to 2-Sided] key.
(2) Touch the [OK] key.
  When the document cover is installed, the [2-Sided to 2-Sided] key and the [2-Sided to 1-Sided] key is not 
displayed.
 The [2-Sided to 2-Sided] key and [2-Sided to 1-Sided] key cannot be used when copying from the document glass.
4
Check the paper to be used.
Make sure that the desired paper (tray) is selected.
 To change the paper (tray), touch the [Paper Select] key.

PAPER TRAYS...

2-20
COPIER
Contents
8
Touch the [Read-End] key.
To cancel scanning of the original and copying...
Press the [STOP] key ( ).
System Settings (Administrator): Initial Status Settings (2-Sided Copy)
The default 2-sided copy mode can be changed.
Read-End
Place next original. Press [Start].
When finished, press [Read-End]. 

2-21
COPIER
Contents
CHANGING THE EXPOSURE AND ORIGINAL 
IMAGE TYPE
The exposure and original image type can be selected to obtain a clear copy.
AUTOMATIC ADJUSTMENT OF THE EXPOSURE AND 
ORIGINAL TYPE
Automatic exposure adjustment operates by default to automatically adjust the exposure level and original type as 
appropriate for the original being copied. (Auto is displayed.)
This function automatically adjusts the image to obtain the most suitable copy.
SELECTING THE ORIGINAL TYPE AND MANUALLY...

2-22
COPIER
Contents
2
Adjust the exposure level.
Touch the   key to make the copy darker.
Touch the   key to make the copy lighter.
Guidelines for the exposure level when [Text] is selected:
1 to 2: Dark originals such as a newspaper
3: Normal density originals
4 to 5: Originals written in pencil or light coloured text
3
Touch the [OK] key.
If [Auto] is selected but the darkness or lightness of the image does not seem quite right...
If the image seems too light or too dark when [Auto] is selected, the...