Sharp Mxc300w Owners Manual

171
SYSTEM SETTINGS
Programs for Fax Mode Programs for Scanner Mode
Program namePage
List Setting
Print Selection
183
Auto Listing184
Initial Setting
Dial Mode
184
Pause Time184
Own Passcode Set184
Set Volume184
TX/RX End Sound185
End Sound Length185
Distinctive Ring185
Remote Reception185
Disable Fax Print Hold185
Sending Function
Original Size Enter
186
Set Res. Con.186
Send Mode186
Quick On Line TX186
Print Station # In Rcvd Data186
Address Review186
Recall Setting (Busy)186
Recall Set (Err)186
Ring...

172
SYSTEM SETTINGS
ADMINISTRATOR SETTINGS MENU
The system settings are accessed via the following menu structure.
Refer to this menu when enabling or disabling the settings that are explained beginning on p.176.
Some settings contain an additional level of settings (a settings screen).
Level 1Level 2Level 3
Change Admin Pw
Default Settings Date & Time Set
Daylight Saving Time
Copier ID Card Setting
Card Shot Default
Default Tray Set
Default Exposure
Sort Auto Select
Limit Of Copies
Printer Notice Page...

173
SYSTEM SETTINGS
Rcv. Function #Of Rings At. RX
#Of Rings Man.RX
Tray Selection
Received Data Print Condition
Auto Rcv Reduce To Regular Size
Duplex Reception
FW. RX Data
Received Data FW. Station Set
Anti Junk Fax
Enter Junk Fax #
Polling Security Polling Security
Polling Passcode # Mode
Network Confirmation of Network
Connection Type Wired
Wireless Infrastructure
Wired + Wireless AP
Wired settings IPv4 Settings
IPv6 Settings
Wireless (Infrastructure) Manual Input of SSID
Wireless (Access Point)...

174
SYSTEM SETTINGS
Operation Setting Auto Clear
Disable Display Timeout
Language Setting
Message Time
Key Touch Sound
Keys Touch Sound At Initial Point
Key Press Time
Disable Auto Key Repeat
Disable Paper Size Set
Energy Save Auto Power Shut-Off
Auto Power Shut-Off Timer
Preheat Mode
Enter Auto Power Shut-Off after
the Remote Job
Toner Save Mode (Copy)
Toner Save Mode (Print)
List Print Fax Settings
Inbound Routing
User Usage List
Activity Report
Junk Fax # List
User Info. Print
AutoColorCalib.
Security...

175
SYSTEM SETTINGS
USING THE SYSTEM SETTINGS
1Press the [SPECIAL FUNCTION] key.
2Select System Settings with the [ ] or [ ] key and press the [OK] key.
3Enter the administrator password with the numeric keys.
   appears for each digit that you enter.
 The mode selection screen appears.
4Select the desired mode with the [ ] or [ ] key.
5Press the [OK] key.
6Select the desired setting with the [ ] or [ ] key.
7Press the [OK] key and follow the instructions in the setting screen.
Several settings will have...

176
SYSTEM SETTINGS
Change Admin Pw
Use this function to change administrator password. 
To change the administrator password, see 
PROGRAMMING AN ADMINISTRATOR 
PASSWORD (p.169).
Default Settings
The default settings for operation of the machine can 
be configured. Select the [Default Settings] to 
configure the settings.
Date & Time Set
Use this to set the date and time in the machines 
built-in clock.
Daylight Saving Time
Enable daylight saving time.
Network
Network settings are described below....

177
SYSTEM SETTINGS
Wireless (Infrastructure)
(Only on models with wireless LAN)
This sets connection using wireless infrastructure 
mode.
Manual Input of SSID
Enter up to 32 half-width characters for the SSID.
Security Type
Select the security type. 
(none/WEP/WPA Personal/WPA2 Personal)
Setting of Encrypt
Select the encryption method based on the Setting of 
Security Type setting.
(none/WEP/TKIP/AES)
Security Key Settings
Set the security key used for wireless connection.
Wireless (Access Point)
(Only...

178
SYSTEM SETTINGS
User Control
User Control is used to configure settings for user 
authentication. Select the [User Control] to configure 
the settings.
User Authentication
These settings enable or disable user authentication 
and specify the authentication method. 
When user authentication is enabled, each user of the 
machine is registered. When a user logs in, settings for 
that user are applied.
User Registration
Users can be added, deleted, and changed.
Function Limit Setting
Set functions that...

179
SYSTEM SETTINGS
Device Control
These settings are used to configure settings for 
hardware functions of the machine. To access one of 
these settings, select Device Control in the mode 
selection screen, select the desired setting in the 
device control screen, and press the [OK] key.
Fusing Control
The temperature of toner fusing is controlled according 
to the weight of the paper that is used.
Fusing Cleaning
Use this function to clean the machines fusing unit 
when dots or other dirt appear on the...

180
SYSTEM SETTINGS
Key Touch Sound
This setting is used to set the length of the key touch 
sound that is heard each time a key is pressed.
The initial factory setting is Short.
Select the desired length with the [ ] or [ ] key.
To turn the key touch sound off, select Off.
Keys Touch Sound At Initial Point
This setting is used to select whether or not a beep will 
sound at preset base settings as you press a key to 
select a setting.
The factory default setting is no beep.
Key Press Time
This setting is...