Sharp Mxc300w Owners Manual

181
SYSTEM SETTINGS
Enter Auto Power Shut-Off after the 
Remote Job
This function works in Auto Power Shut-Off mode. 
When the machine completes a print job received from 
the PC or outputs received fax data, the machine 
immediately returns to the Auto Power Shut-Off mode.
Toner Save Mode (Copy)
Toner Save Mode (Print)
You can reduce the amount of toner used for 
copying/printing.
List Print
This is used to print lists and reports that are only for 
use by the administrator of the machine.
Select the...

182
SYSTEM SETTINGS
Security Settings
The following settings are related to security.
Select the [Security Settings] to configure the settings.
IPsec Settings
IPsec can be used for data transmission/reception on 
a network.
IKEv1 Settings
Configure the IKEv1 settings.
Initialize Private Data and Data in 
Machine
The system-set values can be restored to the factory 
default state after eliminating the data stored in the 
machine.
 All information displayed in the fax status
 Image data in memory boxes...

183
SYSTEM SETTINGS
Sort Auto Select
This setting is used to select the default output mode 
when the document feeder is used for copying.
The initial factory setting is Sort.
Limit Of Copies
This setting is used to set the limit for the number of 
copies that can be set (and that can appear in the 
display) for one copy job.
The factory default setting is 999 copies.
Printer
Settings related to the printer function can be 
configured.
Select the [Printer] to configure the settings.
Notice Page
Set...

184
SYSTEM SETTINGS
Auto Listing
This setting is used to have the activity report that is 
stored in the machines memory printed out at regular 
intervals.
You can choose to have the report automatically 
printed each time the number of stored transactions 
exceeds 50, or have the report printed at a specified 
time every day (only once per day). You can also 
enable both print methods.
The report is normally set to not print out. To have the 
report automatically printed when the number of stored...

185
SYSTEM SETTINGS
TX/RX End Sound
This setting is used to select the beep pattern that 
signals the end of transmission or reception. 
Pattern 1, Pattern 2 or Pattern 3 can be selected.
Before pressing the [OK] key to store your selection, you 
can press the   key to listen to the selected pattern.
End Sound Length
This setting is used to select the length of the end sound
in seconds. Selections are 2.0 sec, 2.5 sec, 3.0 sec,
3.5 sec, and 4.0 sec. 3.0 sec is normally selected.
Distinctive Ring
(Varies...

186
SYSTEM SETTINGS
Sending Function
These settings are used to change the default settings 
(initially set at the factory) for the various fax 
transmission functions to settings that better meet your 
needs.
Select the [Sending Function] to configure the settings.
Original Size Enter
Set the size of originals scanned on the document 
glass. Normally 8-1/2 x 11 is set.
Set Res. Con.
This setting is used to adjust the exposure level when 
scanning an original to be faxed. The initial setting is 
standard...

187
SYSTEM SETTINGS
Rcv. Function
These settings are used to change the default settings 
(initially set at the factory) for the various fax reception 
functions to settings that better meet your needs.
Select the [Rcv. Function] to configure the settings.
#Of Rings At. RX
When the reception mode is set to auto, this setting is 
used to select the number of rings on which the 
machine automatically receives a call and begins fax 
reception. (See RECEIVING A FAX (p.95).)
 Any number of rings from 0 to 15...

188
SYSTEM SETTINGS
FW. RX Data
This setting is used to select whether or not received 
faxes are forwarded to a fax machine programmed as 
explained in Received Data FW. Station Set (p.188) 
in the event that the machine cannot print the faxes. 
The setting is initially disabled.
 The setting is enabled and a checkmark appears in 
the checkbox.
 If the procedure is performed when the setting is 
enabled, the checkmark will be cleared and the 
setting disabled.
Received Data FW. Station Set
When a...

189
SYSTEM SETTINGS
Polling Passcode # Mode
When Polling Security is enabled, use this setting to 
program (or delete) the fax numbers of the machines 
that are allowed to poll your machine. Programmed fax 
numbers are called passcodes. Up to 10 fax numbers 
can be programmed. To check the programmed 
numbers, print the List Print (p.181).
If you make a mistake, move the cursor to the mistake 
with the [ ] or [ ] keys and enter the correct number.
Scanner
System settings for the scanner function are...

190
9
WEB FUNCTIONS IN THE 
MACHINE
ABOUT THE WEB PAGES
The machine includes a built-in Web server. The Web server is accessed using a Web browser on your computer. 
The Web pages include both pages for users and pages for the administrator. In the user Web pages, users can 
monitor the machine, and select printer configuration settings. In the administrator Web pages, the administrator can 
configure the machines e-mail settings, settings for print by e-mail, and passwords. Only the administrator is...