Sharp Mx2310u User Guide

4-117
FACSIMILE
Contents
2
Enter the destination fax number.
(1) Touch the [Address Book] key in the base 
screen.
(2) Touch the one-touch key of the desired 
destination.
If the destination is not stored in the address book, enter 
the fax number with the numeric keys.
If the sub-address and passcode are stored in the one-touch 
key, the following sub-steps are not necessary. Go to step 3.
(3) Touch the [Sub Address] key.
/ appears.
(4) Enter the sub-address with the numeric 
keys.
(5) Touch the [Sub...

4-118
FACSIMILE
Contents
POLLING MEMORY TRANSMISSION USING 
F-CODES
When your machine receives a transmission request from another machine, this function sends a fax stored in an 
F-code memory box (polling memory) in your machine to that machine. The other machine must correctly specify the 
F-code configured in your machine or transmission will not take place.
The document to be transmitted must be scanned into an F-code polling memory box.
SCANNING A DOCUMENT INTO A MEMORY BOX FOR 
F-CODE POLLING...

4-119
FACSIMILE
Contents
3
Touch the [Data Store] key.
4
Touch the key of the F-code memory 
polling box.
5
Specify the number of polling times.
(1) Touch the key for the desired number of 
times.
Touch the [Once] key if you want the document cleared 
from memory after it is transmitted. Touch the [Unlimited] 
key to allow polling an unlimited number of times.
(2) Touch the [OK] key.
6
Select image settings and special 
modes.
 A program, timer setting, transaction report, polling, verif. stamp and...

4-120
FACSIMILE
Contents
7
Press the [BLACK & WHITE START] key.
Scanning begins.
 If you inserted the original pages in the document feeder tray, all pages are scanned.
 If you are scanning the original on the document glass, scan each page one page at a time. 
When scanning finishes, place the next original and press the [BLACK & WHITE START] key. Repeat until all pages have 
been scanned and then touch the [Read-End] key.
To cancel scanning...
Press the [STOP] key ( ) while the original is being...

4-121
FACSIMILE
Contents
CHECKING THE DOCUMENT IN THE F-CODE MEMORY 
POLLING BOX
You can check the document stored in the F-code memory polling box.
A document in a memory box cannot be printed while the document is being transmitted.
1
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Memory Box] key.
☞SPECIAL MODES (page 4-72)
2
Touch the [Data Check] key.
3
Touch the key of the F-code memory 
polling box where the document...

4-122
FACSIMILE
Contents
DELETING A DOCUMENT STORED FOR F-CODE 
POLLING TRANSMISSION
When a document in an F-code memory polling box is no longer needed, follow the steps below to delete it.
A document in a memory box cannot be deleted while the document is being transmitted.
1
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Memory Box] key.
☞SPECIAL MODES (page 4-72)
2
Touch the [Delete Data] key.
3
Touch the key of the...

4-123
FACSIMILE
Contents
RELAY REQUEST TRANSMISSION USING 
F-CODES
This function is used to send a fax to an F-code relay broadcast memory box in another machine and have that machine 
relay the fax to multiple end receiving machines.
When the end receiving machines are far from your machine, sending the fax to a relay machine that is close to the end 
receiving machines can help reduce phone charges. A relay request transmission can be used in combination with the 
timer transmission function to further...

4-124
FACSIMILE
Contents
2
Enter the destination fax number.
(1) Touch the [Address Book] key in the base 
screen.
(2) Touch the one-touch key of the desired 
destination.
If the destination is not stored in the address book, enter 
the fax number with the numeric keys.
If the sub-address and passcode are stored in the one-touch 
key, the following sub-steps are not necessary. Go to step 3.
(3) Touch the [Sub Address] key.
/ appears.
(4) Enter the sub-address with the numeric 
keys.
(5) Touch the [Sub...

4-125
FACSIMILE
Contents
RELAY BROADCAST TRANSMISSION 
USING F-CODES
When your machine receives an F-code relay request transmission, the fax is received to an F-code relay broadcast 
memory box in your machine. Your machine then relays the fax to each of the end receiving machines programmed in 
the memory box. Transmission to the end receiving machines takes place automatically.
 Prior to the operation, inform the requesting party of the sub-address and passcode of the relay broadcast memory box in...

4-126
FACSIMILE
Contents
This section explains how to use an extension phone to make voice calls and receive a fax after talking with the other 
party.
CONNECTING AND USING AN EXISTING 
PHONE (Extension Phone Connection)
You can connect an existing extension phone to the machine.
The phone can be used for voice calls and to start fax reception on the machine.
As an example, you can make a phone call using the existing phone, speak to the other party, and then press the 
[BLACK & WHITE START] key to fax...