Sharp Mx 3501 N Manual

89
Energy Save
The Energy Save settings help reduce power costs. From an environmental perspective, these settings also help reduce 
pollution and conserve natural resources. Touch the [Energy Save] key and configure the settings.
Toner Save in Printer Mode
Toner Save mode can be enabled to reduce toner 
consumption when printing. This setting is only effective 
for printing that does not use the printer driver. When the 
printer driver is used, the printer driver setting takes 
precedence.
To enable...

90
Operation Settings
Settings related to machine operation can be configured. Touch the [Operation Settings] key and configure the settings.
Keys Touch Sound
This setting is used to adjust (or turn off) the volume of 
the beep that sounds when you touch a key. You can 
also have three beeps sound at initial values when 
setting the ratio in copy mode or when adjusting the 
exposure in any mode.
Select one of the keys and touch the [OK] key.
When Key Touch Sound at Initial Point is selected  , 
three...

91
Disabling of Bypass Printing
This setting is used to disable bypass printing (printing 
other jobs ahead of a job that has been stopped* 
because the paper required for the job is not in any of 
the trays).
To enable this setting, select the checkbox   and 
touch the [OK] key.
* This does not include cases where the paper ran out 
during the job.
Key Operation Setting
This setting determines how long a key in the touch 
panel must be touched until the key input is registered. 
The time can be set from...

92
4Select the function that you wish to 
show in the customized key.
Select the key of the desired function and touch the [OK] 
or the [Details] key. Touch the [Details] key to open the 
advanced settings screen for the selected function. Select 
the desired settings and touch the [OK] key.
When the [OK] key is touched, a confirmation message 
will appear. Touch the [Yes] key to apply the selected 
function name to the customized key. (The name of the 
key can also be changed.)
5Touch the [OK] key.
If...

93
Device Control
These settings control devices installed on the machine. Touch the [Device Control] key and configure the settings.
Original Size Detector Setting
One of the five groups of standard original sizes shown 
below can be selected for detection by the original size 
detection function.
Select one of the keys and touch the [OK] key.
To disable detection of original sizes on the document 
glass, select the [Cancel Detection at Document Glass] 
checkbox   and touch the [OK] key.
Disabling of...

94
Disabling of Optional Paper 
Drawer
(When an optional paper drawer is installed.)
This setting is used to disable the optional paper drawer, 
such as when it malfunctions.
To enable this setting, select the checkbox   and 
touch the [OK] key.
Disabling of Tray Setting
This setting is used to prohibit tray (except bypass tray) 
settings.
To enable this setting, select the checkbox   and 
touch the [OK] key.
Disabling of Finisher
(When a saddle stitch finisher or finisher is 
installed.)
This setting is...

95
Auto Paper Selection Setting
The paper types* that the Auto Paper Selection function 
will select can be specified. Select one of the following 
settings:
 Plain Paper
 Plain and Recycle Paper
 Recycle Paper
Select the desired paper type setting and touch the [OK] 
key.
The Auto Paper Selection function will not select any 
paper types other than the paper types specified with 
this setting.
* The paper type set for each paper tray using Paper 
Tray Settings (page 24) in the system settings...

96
Copy Settings
The following settings are related to copying. Touch the [Copy Settings] key and configure the settings.
Default settings selected with these settings apply to all functions of the machine (not just the copy function).
Initial Status Settings
The copier settings are reset when the [POWER] key 
( ) is turned on, when the [CLEAR ALL] key ( ) is 
pressed, or when the auto clear interval has elapsed. 
These settings are used to change the default settings 
for copy mode. The following...

97
Initial Margin Shift Setting
The default setting for margin shift can be set from 0 
(0 mm) to 1 (20 mm) in increments of 1/8 (1 mm).
Specify the default settings for Side 1 (front) and Side 
2 (back) with the   keys and touch the [OK] key. 
(To make the number change quickly, keep your finger 
on the   or   key.)
Erase Width Adjustment
The default setting for erase width can be set from 0 
(0 mm) to 1 (20 mm) in increments of 1/8 (1 mm).
Specify the default settings for the Edge and Center 
with the...

98
Auto Selection Setting of Tray that 
is Supplied the Paper
When this setting is enabled and paper is loaded in a 
tray while the machine is on standby in copy mode, that 
tray is automatically selected.
To enable this setting, select the checkbox   and 
touch the [OK] key.
Initial Color Balance Setting
Color balance values obtained using Color Balance in 
the special modes can be stored in a program (1 to 48), 
and those values can be called up and stored as the 
initial color balance setting.* Use...