Sharp Mx 2300n Service Manual

							MX-2300/2700 N/G  SIMULATION  7 – 25
 
24-2
Purpose: Data clear
Function (Purpose): Used to clear the number of use (the num-
ber of prints) of each paper feed section.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-3
Purpose: Data clear
Function (Purpose): Used to clear the number of use of the fin-
isher, RSPF, and the scan (reading) unit.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-4
Purpose: Data clear
Function (Purpose): Used to clear the maintenance counter, the
printer counters of the transfer unit and the
fusing unit. (After completion of mainte-
nance, clear the counters.)
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel. 
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
MACHINE Machine JAM counter
RSPF RSPF JAM counter
TROUBLE Trouble counter
TRAY1 Tray 1 paper feed counter
TRAY2 Tray 2 paper feed counter
TRAY3 Tray 3 paper feed counter
TRAY4 Tray 4 paper feed counter
MFT TOTAL Manual paper feed counter (Total)
MFT HEAVY Manual paper feed counter (Heavy paper)
MFT OHP Manual paper feed counter (OHP)
MFT ENV Manual paper feed counter (Envelope)
LCC Side LCC paper feed counter (A4LCC)
ADU ADU paper feed counter
0
ARE YOU SURE?YESNO
SIMULATIONNO.2401TEST
JAM/TROUBLE COUNTER DATA CLEAR
EXECUTE
MACHINERSPFTROUBLE
1/1
CLOSE
TRAY1TRAY2TRAY3TRAY4
MFTTOTALMFTHEAVYMFTOHPMFTENV
LCCADU
ARE YOU SURE?YESNOEXECUTE
0
SIMULATIONNO.2402TEST
PAPER F E E D C O U N T E R C L E A R
1/1
CLOSE
RSPF SPF counter
SCAN Scan counter
STAPLER Staple counter
PUNCHER Puncher counter
STAMP Stamp counter
SADDLE STAPLER Saddle staple counter
OC OPEN OC open/close counter
RSPF OPEN OPEN RSPF open/close counter
OC LAMP TIME OC section lamp total lighting time
MAINTENANCE ALL Maintenance counter (Total)
MAINTENANCE COL Maintenance counter (Color)
TC1 BELT Primary transfer unit print counter
TC1 BELT RANGE Primary transfer unit accumulated traveling 
distance (cm)
TC1 BELT DAY Primary transfer unit use day (Day)
TC2 BELT Secondary transfer unit print counter
TC2 BELT RANGE Secondary transfer unit accumulated traveling 
distance (cm)
TC2 BELT DAY Secondary transfer unit use day (Day)
FUSER UNIT Fusing unit print counter
FUSER ACUM DAY Fusing unit use day (Day)
ARE YOU SURE?YESNOEXECUTE
0
SIMULATIONNO.24-03TEST
ORG./OUTPUT COUNTER DATA CLEAR
1/1
CLOSE
RSPFSCANSTAPLERPUNCHER
STAMPSADDLE STAPLEROC OPENRSPF/DSPF O PEN
OC LAMP TIME
0
ARE YOU SURE?YESNO
SIMULATIONNO.2404TEST
MAINTENANCECOUNTER CLEAR
EXECUTE1/1
CLOSE
MAINTENANCE ALLMAINTENANCE COLTC1 BELTTC1 BELT RANGE
TC1 BELT DAYTC2 BELTTC2 BELT RANGETC2 BELT DAY
FUSER UNITFUSER ACUM DAY 
						

							MX-2300/2700 N/G  SIMULATION  7 – 26
 
24-5
Purpose: Data clear
Function (Purpose): Used to clear the developer counter. (After
replacement of developer, clear the
counter.)
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-6
Purpose: Data clear
Function (Purpose): Used to clear the copy counter.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel. 
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-7
Purpose: Data clear
Function (Purpose): Used to clear the OPC drum counter. (After
replacement of the OPC drum, clear the
counter.)
Section:—
Item: Counter (OPC drum)
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-9
Purpose: Data clear
Function (Purpose): Used clear the printer mode print counter
and the self print mode print counter.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
K Developer cartridge print counter (K)
Developer cartridge accumulated traveling distance (cm) (K)
C Developer cartridge print counter (C)
Developer cartridge accumulated traveling distance (cm) (C)
M Developer cartridge print counter (M)
Developer cartridge accumulated traveling distance (cm) (M)
Y Developer cartridge print counter (Y)
Developer cartridge accumulated traveling distance (cm) (Y)
COPY BW Copy (B/W) counter
COPY COL Copy (COLOR) counter
SINGLE COLOR Single color
2COLOR 2-color
0
ARE YOU SURE?YESNO
SIMULATIONNO.2405TEST
DEVELOPERCOUNTER DATA CLEAR
EXECUTE
KCMY
1/1
CLOSE
ARE YOU SURE?YESNOEXECUTE
0
SIMULATIONNO.2406TEST
COPYCOUNTER DATA CLEAR
1/1
COPY BWCOPY COLSINGLE COLOR
CLOSE
9ÞCOLOR
K Drum cartridge print counter (K)
Drum cartridge accumulated traveling distance (cm) (K)
C Drum cartridge print counter (C)
Drum cartridge accumulated traveling distance (cm) (C)
M Drum cartridge print counter (M)
Drum cartridge accumulated traveling distance (cm) (M)
Y Drum cartridge print counter (Y)
Drum cartridge accumulated traveling distance (cm) (Y)
PRINT BW Printer (B/W) counter
PRINT COL Printer (COLOR) counter
OTHER BW Other (BW) counter
OTHER COL Other (COLOR) counter
ARE YOU SURE?YESNOEXECUTE
0
SIMULATIONNO.2407TEST
DRUMCTRGCOUNTERCLEAR
1/1
KCMY
CLOSE
ARE YOU SURE?YESNOEXECUTE
0
SIMULATIONNO.2409TEST
PRINT/OTHER COUNTER CLEAR
1/1
PRINTBWPRINTCOLOTHERBWOTHERCOL
CLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 27
 
24-10
Purpose: Data clear
Function (Purpose): Used to clear the FAX counter. (Only when
FAX is installed)
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel. 
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-15
Purpose: Data clear
Function (Purpose): Used to clear the counters related to the
image send.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-30
Purpose: Data clear
Function (Purpose): Used to initialize the administrator pass-
word.
Section:—
Item: Clear
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button.
The administrator password is initialized.
 
24-31
Purpose: Data clear
Function (Purpose): Used to initialize the service mode pass-
word.
Section:—
Item: Clear
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button.
The service mode password is initialized.
FAX OUTPUT Print quantity counter (for line 1)
FAX OUTPUT_L2 Print quantity counter (for line 2)
FAX SEND Send counter
FAX RECEIVED FAX receive counter
SEND IMAGES FAX send quantity counter (for line 1)
SEND IMAGES_L2 FAX send quantity counter (for line 2)
SEND TIME FAX send time
RECEIVED TIME FAX receive time
ACR SEND Number of carrier prefix attached communications
NET SCN ORG_B/W Network scanner document read quantity 
counter (B/W) (B/W scan job)
NET SCN ORG_CL Network scanner document read quantity 
counter (COLOR) (COLOR scan job)
NET SCN ORG_2CL Network scanner document read quantity 
counter (2-color) (2-color scan job)
NET SCN ORG_SGL Network scanner document read quantity 
counter (Single) (Single scan job)
INTERNET FAX 
OUTPUTInternet FAX output quantity
INTERNET FAX SEND 
OUTPUTInternet FAX send quantity
INTERNET FAX 
RECEIVENumber of internet FAX receive
INTERNET FAX SEND Number of internet FAX send
MAIL COUNTER Number of E-Mail send
FTP COUNTER Number of FTP send
SMB SEND Numeric SMB send
USB CNT Number of USB save
TRIAL MODE_B&C Trial mode counter (B/W & COLOR scan job)
ARE YOU SURE?YESNOEXECUTE
0
SIMULATIONNO.2410TEST
FA XCOUNTERDATACLEAR
1/1
FAXOUTPUTFA X O U T P U T _ L 2
CLOSE
FAX SEND FAX RECEIVED
SEND IMAGESSEND IMAGES_L2SEND TIME RECEIVED TIME
ACRSEND
SCAN TO HDD_B/W Scan to HDD record quantity (B/W)
SCAN TO HDD_CL Scan to HDD record quantity (COLOR)
SCAN TO HDD_2CL Scan to HDD record quantity (2-color)
SCAN TO HDD_SGL Scan to HDD record quantity (Single color)
0
ARE YOU SURE?YESNOEXECUTE
SIMULATIONNO.2415TEST
NETWORK SCANNER COUTNER DATA CLEAR
1/3
CLOSE
NET SCN ORG_B/WNET SCN ORG_CL
NET SCN ORG_2CLNET SCN ORG_SGL
INTERNET FAX OUTPUTINTERNET FAX SEND OUTPUT
INTERNET FAX RECEIVEINTERNET FAX SEND
0
SIMULATIONNO.24-30TEST
ADMIN PASSWORD INITIALIZE
CLOSE
EXECUTEARE YOU SURE?YESNO
0
SIMULATION NO.24-31TEST
SERVICE PASSWORD INITIALIZE
CLOSE
EXECUTEARE YOU SURE?YESNO 
						

							MX-2300/2700 N/G  SIMULATION  7 – 28
 
25
 
25-1
Purpose: Operation test/Check
Function (Purpose): Used to check the operations of the devel-
oping section.
Section: Process (Developing section)
Item: Operation
Operation/Procedure
1) Select the process speed with [MIDDLE] and [LOW] buttons.
2) Press [EXECUTE] button.
The developing motor and the OPC drum motor rotate for 3
min and the detection level of the toner density sensor is dis-
played. 
 
25-2
Purpose: Setting
Function (Purpose): Used to make the initial setting of toner
concentration when replacing developer.
Section: Process (Photoconductor/Developing/
Transfer/Cleaning)
Item: Adjustment
Operation/Procedure
1) Select the adjustment target with the buttons on the touch
panel.
2) Press [EXECUTE] button.
The toner concentration sensor makes sampling of toner con-
centration to display the detection level.
NOTE: When the above operation is interrupted on the way, the
reference toner concentration level is not set. Also when
error code of EE-EC, EE-EL or EE-EU is displayed, the ref-
erence toner concentration level is not set normally.
 
26
 
26-1
Purpose:Setting
Function (Purpose): Used to set the paper exit tray (MX-TRX1).
Section: Paper exit
Item:Setting
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] button to save the entered content in step 1). 
TCD_K Toner concentration sensor K
TCD_C Toner concentration sensor C
TCD_M Toner concentration sensor M
TCD_Y Toner concentration sensor Y
TCV_K Toner concentration control voltage K
TCV_C Toner concentration control voltage C
TCV_M Toner concentration control voltage M
TCV_Y Toner concentration control voltage Y
Display items Item descriptionsDisplay 
rangeDefault 
value
AT DEVE ADJ_L_K Automatic developer 
adjustment value at low 
speed1 – 255 128
AT DEVE ADJ_L_C 1 – 255 128
AT DEVE ADJ_L_M 1 – 255 128
AT DEVE ADJ_L_Y 1 – 255 128
AT DEVE ADJ_M_K Automatic developer 
adjustment value at middle 
speed1 – 255 128
AT DEVE ADJ_M_C 1 – 255 128
AT DEVE ADJ_M_M 1 – 255 128
AT DEVE ADJ_M_Y 1 – 255 128
EXECUTELOWMIDDLE
0
SIMULATIONNO.25-01TEST
TONER SENSOR OUTPUT MONITOR
TCD_9÷:
TCV_9÷:
TCD_C:
TCV_C:
TCD_M:
TCV_M:
TCD_Y:
TCV_::
1/1
CLOSE
AT DEVE VO_L_K Automatic developer 
adjustment control voltage 
at low speed1 – 255 128
AT DEVE VO_L_C 1 – 255 128
AT DEVE VO_L_M 1 – 255 128
AT DEVE VO_L_Y 1 – 255 128
AT DEVE VO_M_K Automatic developer 
adjustment control voltage 
at middle speed1 – 255 128
AT DEVE VO_M_C 1 – 255 128
AT DEVE VO_M_M 1 – 255 128
AT DEVE VO_M_Y 1 – 255 128
TCD_K Toner concentration sensor K
TCD_C Toner concentration sensor C
TCD_M Toner concentration sensor M
TCD_Y Toner concentration sensor Y
TCV_K Toner concentration control K
TCV_C Toner concentration control C
TCV_M Toner concentration control M
TCV_Y Toner concentration control Y
Item Display ContentSet 
rangeDefault
A (0:YES 1:NO) 0 Escape tray YES 0 to 1 1 (NO)
1 Escape tray NO Display items Item descriptionsDisplay 
rangeDefault 
value
0SIMULATIONNO.25-02TEST
AUTOMATIC DEVELOPER ADJUSTMENT
EXECUTE
AT DEVE ADJ_L_K128:AT DEVE VO_L_K128:
AT DEVE ADJ_L_C
128:
AT DEVE VO_L_C128:
AT DEVE ADJ_L_M
128:
AT DEVE VO_L_M128:
AT DEVE ADJ_L_Y
128:128:
1/2
CLOSE
AT DEVE VO_L_YKCMY
0
A:
A9æ0
9ç(0:YES 1:NO)


SIMULATIONNO.269Ù01
ESCAPETRAY SETUP
0
:0:*1:	
OK
TESTCLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 29
 
26-2
Purpose: Setting
Function (Purpose): Used to set the paper size of the large
capacity tray (LCC). (When the paper size
is changed, this simulation must be exe-
cuted to change the paper size in software.)
Section: Paper feed
Item: Setting
Operation/Procedure
Select the paper size with the buttons on the touch panel. 
 
26-3
Purpose: Setting
Function (Purpose): Used to set the specifications of the auditor.
Section: Auditor
Item: Specifications
Operation/Procedure
Select the set target with the button on the touch panel. 
When a button is pressed, the set content is saved. (*): AR-C260 series VENDOR MODE is supported.
Operation 1: Wait for auto clear setting time. Default, 60sec. Can
be changed by the system setting.
Operation 2: Auto clear is not made.
Operation 3: Setting is immediately cleared. The display returns to
the initial screen.
 
26-5
Purpose:Setting
Function (Purpose): Used to set the count mode of the total
counter and the maintenance counter.
Section:—
Item: Counter
Operation/Procedure
1) Select the set item with [↑] [↓] buttons.
2) Enter the set value with 10-key.
3) Press [OK] button.
The set content in step 2) is saved. (Count-up number for A3
paper is 1 or 2.)
* 1 = Count up by 1
2 = Count up by 2
LCC 0 8.5 x 11 (Default: U.S.A, Canada, Inch)
1 A4  (Japan, AB_B, Europe, U.K, 
Australia, AB_A)
2B5
ItemButton 
displayContent Default
BUILT-IN 
AUDITORP10 Built-in auditor mode 
(standard mode) operationP10
EC1 The built-in auditor mode is 
changed to EC1. 
OUTSIDE 
AUDITORNONE Normal operation NONE
P  VENDOR1 Vendor mode for old-type coin 
vendor. Control in the copy 
mode only. 
P OTHER Vendor mode for the other 
external auditor connected to 
the coin vendor I/F
DOC ADJ ON Document filing function 
enabledOFF
OFF Document filing function 
disabled
PF ADJ ON Continuous paper feed is 
performed.OFF
OFF Continuous paper feed is not 
performed.
VENDOR 
MODE (*)MODE1 Vendor mode 1 MODE3
MODE2 Vendor mode 2
MODE3 Vendor mode 3
1/1
SIMULATION NO.26-02TEST
SIZE SETUP
8.511 LCCA4
0
B5
CLOSE
COUNTUP 
TIMING1FUSER_IN The charging timing is when 
passing the sensor paper lead 
edge after fusing.EXIT_OUT
FUSER_OUT The charging timing is when 
passing the sensor paper rear 
edge after fusing.
EXIT_OUT The charging timing is when 
passing the (machine, right) 
tray/after-process unit paper 
exit sensor paper rear edge.
Diagnosis 
settingThe 
specified 
quantity is 
completed. 
Remainder 
of money 
left. Insufficient money during 
copy jobThe 
specified 
quantity is 
completed. 
No 
remainder 
of money. BLACK/
COLOR (No 
remainder 
of money)COLOR 
(Remainder 
of money 
left)
Condition 1 Condition 2 Condition 3 Condition 4
MODE1 Operation 1 Operation 2 Operation 2 Operation 1
MODE2 Operation 1 Operation 1 Operation 2 Operation 1
MODE3 Operation 1 Operation 3 Operation 2 Operation 3
Item Display ContentSetting 
range *Default
A TOTAL (B/W) Total counter (BLACK) 1 to 2 2
B TOTAL (COL) Total counter (COLOR) 1 to 2 2
C MAINTENANCE 
(B/W)Maintenance counter 
(BLACK)1 to 2 2
D MAINTENANCE 
(COL)Maintenance counter 
(COLOR)1 to 2 2
E DEV (B/W) Developer counter 
(BLACK)1 to 2 2
F DEV (COL) Developer counter 
(COLOR)1 to 2 2 ItemButton 
displayContent Default
0
SIMULATIONNO.26-03TEST
AUDITOR SETUP
P10BUILT-INAUDITOREC1 9æ
CLOSE
1/2
POTHEROUTSIDEAUDITOR9æNONEPVENDOR1
9æ
ONOFFDOCADJ
9æONOFFPFADJ
9æMODE1MODE3VENDOR MODEMODE2 
						

							MX-2300/2700 N/G  SIMULATION  7 – 30
 
26-6
Purpose: Setting
Function (Purpose): Used to set the specifications (paper, fixed
magnification ratio, etc.) of the destination.
Section:—
Item: Specifications (Destination)
Operation/Procedure
1) Select the set target with the button on the touch panel.
2) Press [EXECUTE] button.
The selected set content is saved. 
 
26-10
Purpose: Setting
Function (Purpose): Used to set the trial mode of the network
scanner.
Section:—
Item: Operation
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the value is
saved to EEPROM and RAM.

 
26-18
Purpose:Setting
Function (Purpose): Used to set the toner save mode.
Section:—
Item:—
Operation/Procedure
1) Use [↑] and [↓] buttons to select an item.
The set value is highlighted and the value is displayed in the
setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the value is saved to EEPROM and RAM.

U.S.A. United States of America
CANADA Canada
INCH Inch series, other destinations
JAPAN Japan
AB_B AB series (B5 detection), other destinations
EUROPE Europe
U.K. United Kingdom
AUS. Australia
AB_A AB series (A5 detection), other destinations
CHINA China
Item Display ContentSetting 
rangeDefault 
value
A TRIAL MODE 
(0:YES 1:NO)0 Trial mode setting 0 to 1 1
1 Trial mode cancel
0
A:
A9æ2
B9æ2
C9æ2
D9æ29çTOTAL(B/W)
9çTOTAL(COL)
9çMAINTENANCE(B/W)
9çMAINTENANCE(COL)
SIMULATIONNO.269Ù05
A3(11˜17) COUNTUP
2
:1:*2:	
OK
TESTCLOSE
0
SIMULATIONNO.26-06TEST
DISTINATIONSETUP
EXECUTE1/1
U.S.ACANADAINCHJAPAN
AB_BEUROPEU.K.AUS
AB_ACHINA
CLOSE
Item Display ContentSetting 
rangeDefault 
value
ACOPY
(1:YES 0:NO)0 Copy toner save mode 
is allowed0 to 1 0
1 Copy toner save mode 
is inhibited.
B PRINTER
(1:YES 0:NO)0 Printer toner save 
mode is allowed.0 to 1 0
1 Printer toner save 
mode is inhibited.
0
A:
A:1
TRIAL MODE (0:YES 1:NO)
SIMULATION NO.26-10
NETWORK SCANNER TRIAL MODE SETUP
1
[0~ 1]
OK
TESTCLOSE
0
A:
A9æ0
B9æ09çCOPY(1:YES 0:NO)
9çPRINTER(1:YES 0:NO)


SIMULATIONNO.269Ù18
TONER SAVE MODE SETUP
0
:0:*1:	
OK
TESTCLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 31
 
26-30
Purpose: Setting
Function (Purpose): Used to set allow/inhibit of HL slow-up con-
trol (CE mark support control).
Section:—
Item: Specifications (Operation mode (common
operation))
Operation/Procedure
1) When the machine enters the simulation, the following screen
is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.

NOTE: Even though the control is allowed, the CE mark support
control may not be executed depending on the power fre-
quency, etc.

 
26-35
Purpose: Setting
Function (Purpose): Used to set the trouble memory saving pro-
cedure.
Section:—
Item:—
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
 
26-38
Purpose:Setting
Function (Purpose): Used to set Continue/Stop of print when the
developer life is reached.
Section: Other
Item: Specifications (Operation mode)
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.

 
26-41
Purpose:Setting
Function (Purpose): Used to set YES/NO of AMS setting in the
center binding mode.
Section:—
Item: Specifications (Operation mode)
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, and the current entered value is
saved to EEPROM and RAM.
Item Display ContentSetting 
rangeDefault value
A (0:YES 1:NO) 0 CE mark 
control allowed0 to 1 Refer to . 1 CE mark 
control inhibited
Destination Setting value 
U.S.A 1 (CE not supported)
CANADA 1 (CE not supported)
INCH 1 (CE not supported)
JAPAN 1 (CE not supported)
AB_B 1 (CE not supported)
EUROPE 0 (CE supported)
U.K 0 (CE supported)
AUS. 0 (CE supported)
AB_A 0 (CE supported)
CHINA 0 (CE supported)
A:A9
						

							MX-2300/2700 N/G  SIMULATION  7 – 32 * When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.


 
26-49
Purpose: Setting
Function (Purpose): Used to set the copy speed mode.
Section:—
Item: Setting
Operation/Procedure
1) When the machine enters Simulation 26-49, the current set
status is displayed.
* The current set button is highlighted.
2) Select an item to be changed, and it is highlighted. The setting
is saved to EEPROM and RAM.
* Only one can be selected for each item.

 
26-50
Purpose:Setting
Function (Purpose): Used to set functions.
Section:—
Item: Specifications (Operation)
Operation/Procedure
1) Select an item to be set with [↑] and [↓] buttons.
The selected value is highlighted and the value is displayed in
the setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the entered value is set.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the current set value is saved to EEPROM and RAM.


* OFF: Inhibit cancel state
ON: Inhibit state
Item Display ContentSetting 
rangeDefault value
A (0:YES 
1:NO)0 Center binding 
mode AMS setting0 to 1 Refer to . 1 Center binding 
mode AMS cancel
Destination Setting value 
U.S.A 0 (Cancel) 
CANADA 0 (Cancel) 
INCH 0 (Cancel) 
JAPAN 0 (Cancel) 
AB_B 0 (Cancel) 
EUROPE 1 (Setting)  
U.K 1 (Setting) 
AUS. 0 (Cancel) 
AB_A 0 (Cancel) 
CHINA 0 (Cancel) 
ItemSet 
valueContentDefault 
value
POSTCARD LOW Postcard copy speed LOW LOW
HIGH Postcard copy speed HIGH
0
A:A9æ0
9ç(0:YES 1:NO)
SIMULATIONNO.26-41
PAMPHLET MODE AMS SETTING.
0
:0:*1:	
OK
TESTCLOSE
1/1
SIMULATIONNO.26-49TEST
COPYSPEEDMODESETUPLOW POSTCARD9
						

							MX-2300/2700 N/G  SIMULATION  7 – 33 
 
26-52
Purpose: Setting
Function (Purpose): Used to set whether non-printed paper
(insertion paper, cover paper) is counted up
or not.
Section:—
Item:—
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the entered value is set.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.


 
26-53
Purpose:Setting
Function (Purpose): Used to set YES/NO of the auto color cali-
bration.
Section:—
Item:—
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current set value is saved to
EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.

 
26-54
Purpose:Setting
Function (Purpose): Used to set the printer calibration YES/NO.
Section:Printer
Item: Operation
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, and the current set value is
saved to EEPROM and RAM.
After completion of setting, [OK] button returns to the normal
display.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.

Destination Setting value A  Setting value B
U.S.A 1 (Display allowed)  0
CANADA 1 (Display allowed)  0
INCH 1 (Display allowed)  0
JAPAN 1 (Display allowed)  7
AB_B 1 (Display allowed)  0
EUROPE 1 (Display allowed)  0
U.K 0 (Display inhibited) 0
AUS. 1 (Display allowed)  0
AB_A 1 (Display allowed)  0
CHINA 1 (Display allowed)  0
Item Display ContentSetting 
rangeDefault value
A (0:YES 
1:NO)0 White paper 
countup (YES)0 to 1 Refer to .
1 White paper 
coutup (NO)
Destination Setting value 
U.S.A 0 (countup)
CANADA 0 (countup)
INCH 0 (countup)
JAPAN 1 (No countup)
AB_B 0 (countup)
EUROPE 0 (countup)
U.K 0 (countup)
AUS. 1 (No countup)
AB_A 0 (countup)
CHINA 0 (countup)
0
A:
A9æ1
B9æ0
C9æ0;BW REVERSE : YES
;COLORMODE
;FINISHERFUNCTION : NO
SIMULATION NO.26-50
FUNCTIONSETTING
1
:0:*1:	
OK
TESTCLOSE
0
A:
A9æ1
9ç(0:YES 1:NO)
SIMULATIONNO.26-52
A BLANK PAPER COUNT MODE SETUP
1
:0:*1:	
OK
TESTCLOSE
Item Display ContentSetting 
rangeDefault 
value
A (1:YES 0:NO) 1 ACC YES 0 to 1 1
0 ACC NO
Item Display ContentSetting 
rangeDefault 
value
A (1:YES 0:NO) 1 ACC YES 0 – 1 1
0 ACC NO
0
A:
A9æ1
9ç(1:YES 0:NO)
SIMULATIONNO.26-53
ENABLING OF AUTOMATIC COLOR CALIBRATION
1
:0:*1:	
OK
TESTCLOSE
0
A:
A9æ1
9ç(1:YES 0:NO)
SIMULATIONNO.269Ù54
ENABLING OF AUTOMATIC COLOR CALIBRATIONOFPRINTER
1
:0:*1:	
OK
TESTCLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 34
 
26-65
Purpose: Setting
Function (Purpose): Used to set the finisher alarm mode.
Section:—
Item: Specifications
Operation/Procedure
1) When the machine enters Simulation 26-65, the following
screen is displayed.
* The current set value is highlighted.
2) When the set value button of an item to be changed is
pressed, it is highlighted and the setting is saved to EEPROM
and RAM.
* Only one can be selected for each item.


* Valid only when the 1K finisher is installed.
[Target paper size]
Staplable S-size paper described on the product specifications
A4, A4R, B5, B5R, 8.5 x 11, 8.5 x 11R, 16K, 16KR
* 25 sheets for L-size paper (A3, B4, 11 x 17, 8.5 x 14, 8.5 x 13,
8K) regardless of setting
* 25 sheets for mixed loading of a same width regardless of setting
 
26-67
Purpose:Setting
Function (Purpose): Used to set the summer time (switching
timing to the summer time and the adjust-
ment time (shift amount)) and the time zone
(for switching to the summer time and the
difference between the local time and GMT
(UTC) for synchronization with the internet
time server).
Section:—
Item: Specifications
Operation/Procedure
1) Select a mode to be set. ([SUMMER TIME] is selected in this
example.)
* When [TIME ZONE] or [SUMMER TIME] button is pressed,
it is highlighted and item of the selected button is displayed.
* Only one can be selected, and the selected button is high-
lighted.
In the default display, [TIME ZONE] is selected.
2) Change the set item with [↑] and [↓] buttons.
The highlighted section of the set value is switched and the
value is displayed in the setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
3) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
4) When [OK] button is pressed, it is highlighted and the current
set value is saved to EEPROM and RAM.
After completion of setting, [OK] button returns to the normal
display.
* When [OK], [↑], [↓] button,  [COLOR], or [BLACK] key is
pressed, the current set value is saved to EEPROM and
RAM.

ItemSet 
valueContentSetting 
rangeDefault 
value
LIMIT 
SHEETS30 Staple limit sheets: 30 sheets 30 or 50 30
50 Staple limit sheets: 50 sheets
LIMIT 
COPIESON Staple limit copies ON ON or OFF ON
OFF Staple limit copies OFF
SIMULATION NO.26-65TEST
FINISHER ALARM MODE SETUP (STAPLE LIMIT)
3050LIMIT SHEETS :
1/1
0
ONOFFLIMIT COPIES :
CLOSE
Category Item Display ContentSetting 
rangeDefault 
valueRemark
TIME ZONE A GMT +/- + GMT +/– 0 1
–1
B GMT HOUR GMT HOUR 0  to 13 *
C GMT MINUTE GMT MINUTE 0  to 59 *
D INTERNET YES Internet time YES/
NO0 * When YES, time is synchronized with 
the internet time server.
NO 1
SUMMER 
TIMECommon A AUTO SUMMER 
TIME ADJON Auto summertime 
setting ON/OFF0*
OFF 1
B ADJ TIME HOUR Adjustment time 
HOUR0  to 23 1
C ADJ TIME MINUTE Adjustment time 
MINUTE0  to 59 *