Sharp Mx 2300n Service Manual

							MX-2300/2700 N/G  SIMULATION  7 – 15
 
6-2
Purpose: Operation test/check
Function (Purpose): Used to check the operations of each fan
motor and its control circuit.
Section: Other
Item: Operation
Operation/Procedure
1) Select the item to be checked with the buttons on the touch
panel.
2) Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.
 
6-3
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the primary
transfer unit and the related circuit. 
Section: Process (Transfer)
Item: Operation
Operation/Procedure
1) Press [EXECUTE] button.
2) The load operation is started. (Separation operation: BLACK
→ COLOR → FREE  Stops at each position for 5 sec.) During
the operation, the current position is displayed.
 
7
 
7-1
Purpose:Setting
Function (Purpose): Used to set the operating conditions of
aging.
Section: Other
Item: Operation
Operation/Procedure
1) Select the target to be set with buttons on the touch panel.
2) Press [EXECUTE] button.
The machine is rebooted in the aging mode. 
The contents set with this simulation are retained until the
power is turned OFF. 
 
7-6
Purpose:Setting
Function (Purpose): Used to set the intermittent aging cycle.
Section: Other
Item: Operation
Operation/Procedure
1) Enter the intermittent aging cycle (unit: sec) with 10-key.
2) Press [OK] button.
The time entered in procedure 1) is set.
POFM Paper exit cooling fan motor (* POFM_U, POFM_F, and 
POFM_R are driven at the same time.)
OZFM Ozone fan motor
PSFM Power cooling fan motor
BLACK Black mode position Black mode position
→ COLOR mode position
→ Drum separation position
→ Shift to the black mode 
position is repeated. COLOR COLOR mode position
FREE Drum separation position
:w
:w
:w
:w
:w
:w
:w
:w
SIMULATIONNO.0602TESTFA N L O A D S E T U P
POFMOZFM
PSFM
1/1EXECUTE
0CLOSE
0SIMULATIONNO.0603TESTTRANSFER LOAD CHECK
EXECUTE
POSITION:


1/1
CLOSE
AGING Aging operation setup
INTERVAL Intermittent setup
MISFEED DISABLE JAM detection enable/disable setup
FUSING DISABLE Fusing operation enable/disable setup
WARMUP DISABLE Warm-up disable setup
DV CHECK DISABLE DV unit detection enable/disable setup
SHADING DISABLE Shading disable setup
CCD GAIN FREE CCD gain adjustment free setup
Item Item Set range Default value
A CYCLE TIME(SEC) 1 to 900 3
SIMULATIONNO.0701TEST
AGINGTEST SETTING
AGINGINTERVAL
MISFEED DISABLEFUSING DISABLE
WARMUP DISABLEDV CHECK DISABLE
1/1EXECUTE
0
SHADING DISABLECCD GAIN FREE
CLOSE
0
A:
A9æ3
9çCYCLE TIME(SEC)


SIMULATIONNO.07-06
INTERVALAGINGCYCLETIMESETUP
3
:1:*900:	
OK
TESTCLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 16
 
7-8
Purpose: Operation display
Function (Purpose): Used to display the warm-up time. 
Section:Fusing
Item: Operation
Operation/Procedure
Press [EXECUTE] button.
Counting of the warm-up time is started.
* Interruption of counting by pressing [EXECUTE] button is inhib-
ited. 
 
7-9
Purpose: Operation test/check
Function (Purpose): Used to check printing in the color mode.
Section:—
Item: Operation
Operation/Procedure
1) Select a print color with buttons on the touch panel.
2) Press [EXECUTE] button.
Printing is started in the selected color.
* If no color is specified, printing is made in all colors.
 
8
 
8-1
Purpose: Operation test/Check/Adjustment
Function (Purpose): Used to check and adjust the operations of
the developing voltage of each color and
the control circuit.
Section: Process (Photoconductor/Developing/
Transfer/Cleaning)
Item: Operation
Operation/Procedure
1) Select a speed with [MIDDLE] and [LOW] buttons on the touch
panel. 2) Select a target item to be adjusted with [↑] [↓] buttons.
3) Enter the adjustment value with 10-key.
4) Press [EXECUTE] button.
The set value is saved and the voltage corresponding to the
set value is outputted for 30 sec.
* The adjustment values of [MIDDLE] and [LOW] are related
together.
* When [EXECUTE] button is pressed, the output is terminated.
 
8-2
Purpose: Operation test/Check/Adjustment
Function (Purpose): Used to check and adjust the operation of
the main charger grid voltage in each
printer mode and the control circuit.
Section: Process (Photoconductor/Developing/
Transfer/Cleaning)
Item: Operation
Operation/Procedure
1) Select a speed with [MIDDLE] and [LOW] buttons on the touch
panel.
2) Select a target item to be adjusted with [↑] [↓] buttons. 
3) Enter the adjustment value with 10-key.
4) Press [EXECUTE] button.
The set value is saved and the voltage corresponding to the
set value is outputted for 30 sec.
* The adjustment values of [MIDDLE] and [LOW] are related
together.
* When [EXECUTE] button is pressed, the output is terminated. 
K Setup/cancel of black
C Setup/cancel of cyan
M Setup/cancel of magenta
Y Setup/cancel of yellow
0
SIMULATIONNO.0708TEST
WARM UP TIME DISPLAY SETTING
CLOSE
EXECUTE
0SECONDS
CLOSE
0
K
SIMULATIONNO.0709TEST
PRINTING COLOR SELECT(COLOR MODE)
CMY
1/1EXECUTE
Button Item Display ContentSetting 
rangeDefault 
value
MIDDLE A MIDDLE 
SPEED DVB_KK developing 
bias set value 
at middle speed0 to 700 450
B MIDDLE 
SPEED DVB_CC developing 
bias set value 
at middle speed0 to 700 450
C MIDDLE 
SPEED 
DVB_MM developing 
bias set value 
at middle speed0 to 700 450
D MIDDLE 
SPEED DVB_YY developing 
bias set value 
at middle speed0 to 700 450
LOW A LOW SPEED 
DVB_KK developing 
bias set value 
at low speed0 to 700 430
B LOW SPEED 
DVB_CC developing 
bias set value 
at low speed0 to 700 430
C LOW SPEED 
DVB_MM developing 
bias set value 
at low speed0 to 700 430
D LOW SPEED 
DVB_YY developing 
bias set value 
at low speed0 to 700 430
:w0
A:
A9æ450
B9æ450
C9æ4509çMIDDLESPEEDDVB_K
9çMIDDLESPEEDDVB_C
9çMIDDLESPEEDDVB_M
SIMULATIONNO.089Ù01
DV SETTING AND OUTPUT
450
:0:*700:	
OK
TESTCLOSE
EXECUTE
D9æ4509çMIDDLESPEEDDVB_Y
LOWMIDDLE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 17
 
8-6
Purpose: Operation test/Check/Adjustment
Function (Purpose): Used to check and adjust the operation of
the transfer voltage and the control circuit.
Section: Process (Photoconductor/Developing/
Transfer/Cleaning)/Transfer
Item:Setting
Operation/Procedure
1) Select a target item to be adjusted with [↑] [↓] buttons.
2) Enter the adjustment value with 10-key.
3) Press [EXECUTE] button.
The set value is saved and the voltage corresponding to the
set value is outputted for 30 sec.
When [EXECUTE] button is pressed, the output is terminated.
Button Item Display ContentSetting 
rangeDefault 
value
MIDDLE A MIDDLE 
SPEED 
GB_KK charging/grid 
bias set value at 
middle speed230 to 850 615
B MIDDLE 
SPEED 
GB_CC charging/grid 
bias set value at 
middle speed230 to 850 615
C MIDDLE 
SPEED 
GB_MM charging/grid 
bias set value at 
middle speed230 to 850 615
D MIDDLE 
SPEED 
GB_YY charging/grid 
bias set value at 
middle speed230 to 850 615
LOW A LOW 
SPEED 
GB_KK charging/grid 
bias set value at 
low speed230 to 850 605
BLOW 
SPEED 
GB_CC charging/grid 
bias set value at 
low speed230 to 850 605
CLOW 
SPEED 
GB_MM charging/grid 
bias set value at 
low speed230 to 850 605
DLOW 
SPEED 
GB_YY charging/grid 
bias set value at 
low speed230 to 850 6050
A:
A9æ615
B9æ615
C9æ6159çMIDDLESPEEDGB_K
9çMIDDLESPEEDGB_C
9çMIDDLESPEEDGB_M
SIMULATIONNO.089Ù02
MHV/GRIDSETTING AND OUTPUT
615
:230:*850:	
OK
TESTCLOSE
EXECUTE
D9æ6159çMIDDLESPEEDGB_Y
LOWMIDDLE
Item Display ContentSetting 
rangeDefault 
valueActual output 
setting rangeDefault 
value
Actual 
output value
A TC1 LOW SPEED CL K Primary transfer 
bias reference 
valueCOLOR K Low speed 0 to 255 232 –500V to 5000V 4500V
B TC1 MIDDLE SPEED CL K Middle speed 0 to 255 232 –500V to 5000V 4500V
C TC1 LOW SPEED CL CMY CMY Low speed 0 to 255 139 –500V to 5000V 2500V
D TC1 MIDDLE SPEED CL CMY Middle speed 0 to 255 139 –500V to 5000V 2500V
E TC1 LOW SPEED BW K BLACK K Low speed 0 to 255 232 –500V to 5000V 4500V
F TC1 MIDDLE SPEED BW K Middle speed 0 to 255 232 –500V to 5000V 4500V
G TC2 PLAIN CL SPX Secondary transfer 
bias reference 
valueCOLOR Normal 
paperFront surface 51 to 255 100 2µA to 45µA12.5µA
H TC2 PLAIN CL DPX Back surface 51 to 255 100 2µA to 45µA12.5µA
I TC2 PLAIN BW SPX BLACK Front surface 51 to 255 90 2µA to 45µA10µA
J TC2 PLAIN BW DPX Back surface 51 to 255 90 2µA to 45µA10µA
K TC2 HEAVY1 CL SPX COLOR Heavy paper 51 to 255 69 2µA to 45µA6µA
L TC2 HEAVY1 BW SPX BLACK 51 to 255 69 2µA to 45µA6µA
M TC2 OHP CL COLOR OHP 51 to 255 60 2µA to 45µA4µA
N TC2 OHP BW BLACK 51 to 255 60 2µA to 45µA4µA
O TC2 ENVELOPE CL COLOR Envelope 51 to 255 184 2µA to 45µA30µA
P TC2 ENVELOPE BW BLACK 51 to 255 184 2µA to 45µA30µA
Q TC2 CLEANING Cleaning process 51 to 255 79 2µA to 45µA8µA
R TC2 CLEAN LOW SPD Secondary transfer 
cleaning bias 
reference valueLow speed print 51 to 255 72 –50V to –1500 –200V
S TC2 CLEAN MIDDLE SPD Middle speed print 51 to 255 72 –50V to –1500V –200V
T TC2 CLEAN CLEANING Cleaning 51 to 255 156 –50V to –1500V –800V
CLOSE
A:
A : 232
B : 232
C: 139TC1 LOW SPEEDCLKTC1 MIDDLE SPEEDCLKTC1 LOW SPEEDCLCMY
SIMULATIONNO.08-06
THV SETTING AND OUTPUT
232
[ 0~255]
OK
TEST
EXECUTE
0
D : 139TC1 MIDDLE SPEED CLCMY
CLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 18
 
9
 
9-2
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the sen-
sors and detectors in the duplex section
and its control circuit.
Section: Duplex
Item: Operation
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
 
9-3
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the loads
in the duplex section and the control cir-
cuits. 
Section: Duplex
Item: Operation
Operation/Procedure
1) Select the item to be operation tested with the buttons on the
touch panel.
2) Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the output is terminated.
 
10
 
10-1
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the toner
motor and the related circuit.
Section: Process (Developing)
Item: Operation
Operation/Procedure
* Before execution of this simulation, remove the toner cartridges.
1) Select the item to be checked with the buttons on the touch
panel.
2) Press [EXECUTE] button.
* The selected load operation is performed for 10 sec.
* When [EXECUTE] button is pressed, the operation is termi-
nated.
 
13
 
13--
Purpose: Clear/cancel (Trouble etc.)
Function (Purpose): Used to cancel the self-diag U1 trouble.
Section:FAX
Item: Trouble
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button to execute cancellation of the trouble. 
DSW_ADU ADU transport open/close detection
APPD1 ADU transport path detection 1
APPD2 ADU transport path detection 2
ADUM_L ADU motor lower
0
ADUSENSORCHECK
1/1
CLOSESIMULATIONNO.099Ù02TEST
1/1
DSW_ADUAPPD1 APPD2
0SIMULATIONNO.09-03TESTADU LOAD CHECK
EXECUTE1/1
ADUM_L
CLOSE
TNM_K Toner motor K
TNM_C Toner motor C
TNM_M Toner motor M
TNM_Y Toner motor Y
0SIMULATIONNO.10-01TESTTONER MOTOR ACTIVATION
EXECUTE1/1
TNM_K
CLOSE
TNM_CTNM_MTNM_Y
0SIMULATIONNO.13TESTU1TROUBLE CANCELLATION
CLOSE
EXECUTEARE YOU SURE?YESNO 
						

							MX-2300/2700 N/G  SIMULATION  7 – 19
 
14
 
14--
Purpose: Clear/cancel (Trouble etc.)
Function (Purpose): Used to cancel excluding the self-diag U1/
LCC/U2/PF troubles.
Section:—
Item: Trouble
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button to execute cancellation of the trouble. 
 
15
 
15--
Purpose: Clear/cancel (Trouble etc.)
Function (Purpose): Used to cancel the self-diag U6-09 (large
capacity paper feed tray) trouble.
Section:LCC
Item: Trouble
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button to execute cancellation of the trouble. 
 
16
 
16--
Purpose: Clear/cancel (Trouble etc.)
Function (Purpose): Used to cancel the self-diag U2 trouble.
Section: MFPcnt PWB / PCU PWB / SCU PWB
Item: Trouble
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button to execute cancellation of the trouble. 
 
17
 
17--
Purpose: Clear/cancel (Trouble etc.)
Function (Purpose): Used to cancel the self-diag PF.
Section: Communication unit (RIC/MODEM)
Item: Trouble
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button to execute cancellation of the trouble. 
 
21
 
21-1
Purpose:Setting
Function (Purpose): Used to set the maintenance cycle.
Section:—
Item: Specifications
Operation/Procedure
1) Select an item corresponding to the set contents with [↑] [↓]
buttons. 
2) Enter the value corresponding to the maintenance timing with
10-key. 
3) Press [OK] button to save the entered conditions in step 2). 
0
SI MU LA TI O NNO.14TEST
TRO U BLE CA N CE LLATIO N(O THER)
CLOSE
EXECUTEARE YO U S U RE ?YESNO
0
SIMULATIONNO.15TEST
LCCTROUBLE CANCELLATION
CLOSE
EXECUTEARE YOU SURE?YESNO
Item Display Content Set rangeDefault 
value
A MAINTENANCE 
COUNTER 
(TOTAL)Maintenance 
counter 
(total)0: DEFAULT, 
1 – 300: 1K – 300K 
999: FREE100K
B MAINTENANCE 
COUNTER 
(COLOR)Maintenance 
counter 
(color)0: DEFAULT,
1 – 300: 1K – 300K 
999: FREE60K
0
SIMULATIONNO.16TEST
U2TROUBLE CANCELLATION
CLOSE
EXECUTEARE YOU SURE?YESNO
0
SIMULATION NO.17TEST
PF TROUBLE CANCELLATION
CLOSE
EXECUTEARE YOU SURE?YESNO 
						

							MX-2300/2700 N/G  SIMULATION  7 – 20
 
22
 
22-1
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the print count value in each
section and each operation mode. (Used to
check the maintenance timing.)
Section:—
Item: Counter
Operation/Procedure
Change the display page with [↑] [↓] buttons.
Press [COLOR] or [BLACK] button to print. 
 
22-2
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the total numbers of misfeed
and troubles. (When the number of total
jam is considerably great, it is judged as
necessary for repair.)
Section:—
Item: Counter
Operation/Procedure
The paper jam/trouble counter value is displayed.
Press [COLOR] or [BLACK] button to print. 
 
22-3
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check misfeed positions and the
misfeed count of each position.
Section:—
Item: Trouble
Operation/Procedure
The history of paper jams and misfeed is displayed.
The above histories are displayed from the newest one to the old-
est in this sequence. The max. 50 items are saved. (The oldest one
is sequentially erased.)
* List of JAM codes: Refer to 2. Paper JAM code in the [12]
OTHERS.
TOTAL OUT(BW) Total output quantity of black
TOTAL OUT(COL) Total output quantity of color
TOTAL(BW) Total use quantity of black
TOTAL(COL) Total use quantity of color
TOTAL(2COL) Total use quantity of 2-color
TOTAL(SGL_COL) Total use quantity of single color
COPY(BW) Black copy counter
COPY(COL) Color copy counter
COPY(2COL) 2-color copy counter
COPY(SGL_COL) Single color copy counter
PRINT(BW) Black print counter
PRINT(COL) Color print counter
DOC FIL(BW) Black document filing print counter
DOC FIL(COL) Color document filing print counter
DOC FIL(2COL) 2-color document filing print counter
DOC FIL(SGL COL) Single-color document filing print counter
OTHER(BW) Black other counter
OTHER(COL) Color other counter
MAINTENANCE ALL Maintenance counter (Total)
MAINTENANCE COL Maintenance counter (Color)
TC1 BELT Primary transfer unit print counter
TC1 BELT RANGE Primary transfer unit accumulated traveling 
distance (cm)
TC1 BELT DAY Use day of primary transfer (Day)
TC2 BELT Secondary transfer unit print counter
TC2 BELT RANGE Secondary transfer unit accumulated traveling 
distance (cm)
TC2 BELT DAY Use day of secondary transfer unit (Day)
FUSER UNIT Fuser unit print counter
FUSER ACUM DAY Use day of fuser unit (Day)
DRUM LIFE(K) Accumulated number of drum rotations (K)
DRUM LIFE(C) Accumulated number of drum rotations (C)
DRUM LIFE(M) Accumulated number of drum rotations (M)
DRUM LIFE(Y) Accumulated number of drum rotations (Y)
DEVE LIFE(K) Accumulated number of developer rotations (K)
DEVE LIFE(C) Accumulated number of developer rotations (C)
DEVE LIFE(M) Accumulated number of developer rotations (M)
DEVE LIFE(Y) Accumulated number of developer rotations (Y)
0
A
A: 0
B: 0; MAINTENANCE COUNTER (TOTAL)
; MAINTENANCE COUNTER (COLOR)
SIMULATION NO.21-01
MAINTENANCE CYCLE SETUP
0
[ 1~300]
OK
TESTCLOSE
MACHINE JAM Machine JAM counter
RSPF/DSPF JAM SPF JAM counter
TROUBLE Trouble counter
TOTAL OUT(BW)
SIMULATION NO.22-01TEST
COUNTER DISPLAY
CLOSE
TOTAL(SGL_COL)
TOTAL OUT(COL) COPY(BW)
TOTAL(BW) COPY(COL)
TOTAL(COL) COPY(2COL)
TOTAL(2COL): 00000000
: 00000000
: 00000000
: 00000000
: 00000000: 00000000
: 00000000
: 00000000
: 00000000
: 00000000 COPY(SGL_COL)
1/3
0
MACHINE JAMSIMULATION NO.22-02
TEST
JAM/TROUBLE COUNTER DISPLAY
CLOSE
RSPF/DSPF JAM
TROUBLE: 00000000
: 00000000
: 00000000
1/1
0
0CLOSEJAM HISTORY DATA DISPLAY
1/1
SIMULATION NO.22-03TEST
1/1
PPD2_N1 CPFD2_S2 MFT TRAY3
PPD2_N1 CPFD2_S2 APPD3_S DPFD2_S4
LCC PPD2_PRI CPID2_S2 CPID2_S2
CPFD1_N1 PPD2_PRI TRAY3 APPD3_S
TRAY2 MFT 
						

							MX-2300/2700 N/G  SIMULATION  7 – 21
 
22-4
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the trouble (self diag) his-
tory.
Section:—
Item: Trouble
Operation/Procedure
The trouble history is displayed.
The trouble history is displayed sequentially from the latest one.
The max. 30 items can be stored. (The oldest one is deleted
sequentially.)
Press [COLOR] or [BLACK] button to print.
* Trouble code list: Refer to 2. Trouble code list in the [8] SELF
DIAG AND TROUBLE CODE.
 
22-5
Purpose: Others
Function (Purpose): Used to check the ROM version of each
unit (section).
Section:—
Item: Software
Operation/Procedure
The ROM version can be checked with [↑] [↓] buttons.
When there is any problem in the software, use this simulation to
check the ROM version of each section and revise the version if
necessary.
Press [COLOR] or [BLACK] button to print. 
 
22-6
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to output the list of the setting and
adjustment data (simulations, FAX soft
switch, counters).
Section:—
Item: Data (Setting, adjustment data)
Operation/Procedure
* When installing or servicing, this simulation is executed to print
the adjustment data and set data for use in the next servicing.
(Memory trouble, PWB replacement, etc.)
1) Select the print mode with 10-key.
2) Press [EXECUTE] button.
The list print selected in step 1) is started.
* When [C] key, [CA] key, [SYSTEM SETTINGS] key, or [EXE-
CUTE] button is pressed during printing, the operation is ter-
minated.
 
22-8
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the number of use of the fin-
isher, the RSPF, and the scan (reading)
unit.
Section:—
Item: Counter
Operation/Procedure
The values of the finisher counter, the RSPF counter, and the scan-
ner (read) related counters are displayed.
Press [COLOR] or [BLACK] button to print.
S/N Serial No. 
ICU(MAIN) ICU (Main section)
ICU(BOOT) ICU (Boot section)
LANGUAGE Language support data version
GRAPHIC Graphic data for LCD
IMG DATA ROM ImageASIC FlashROM data
COLOR PROFILE Color profile
PCU PCU
SCU SCU
SPF SPF
FAX1(MAIN) FAX1 line (Main section)
FAX2(MAIN) FAX2 line (Main section)
DESK Desk unit
LCC Side LCC
FINISHER Finisher
SADDLE Saddle unit
PUNCH Punch unit
NIC NIC
POWER-CON Power controller
E-MANUAL Operation manual (HDD storage)
0CLOSE
TROUBLE CODE DATA DISPLAYSIMULATION NO.22-04TEST
1/2
E7-23 F9-20 F2-39 L4-31
F1-50 L4-02 F2-39 F1-50
F1-50 L4-02 F1-61 F1-50
F1-50 F2-39 H5-01 E7-23
U5-12 F2-39 L1-00 E7-23
ItemDisplay item & 
detail displayDescriptionSet 
rangeDefault 
value
A DATA PATTERN Data pattern selection
1: List print
2: List print (Sim50-24)1 to 2 1
RSPF/DSPF Document feed quantity
SCAN Number of scan
STAPLER Staple counter
PUNCHER Puncher counter
STAMP Stamp counter
SADDLE STAPLER Saddle staple counter
OC_OPEN OC open/close counter
RSPF/DSPF_OPEN RSPF/DSPF open/close counter
OC LAMP_TIME Total lighting time of the lamp in OC section
SIMULATION NO.22-05
S/N : **********
TESTCLOSE0
ICU(MAIN) : 00.00.00
ICU(BOOT) : 00.00.00
LANGUAGE : 00.00.00
GRAPHIC : 00.00.00
IMG DATA ROM : 00.00.00COLOR PROFILE : 00.00.00
PCU : 00.00.00
SCU : 00.00.00
SPF : NONE
FAX1(MAIN) : NONE
1/2
0
A:A: 1
; DATA PATTERN
SIMULATION NO.22-06
DATA PRINT MODE
1
[1~2]
OK
TEST
EXECUTE
CLOSE 
						

							MX-2300/2700 N/G  SIMULATION  7 – 22
 
22-9
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the number of use (print
quantity) of each paper feed section.
Section: Paper feed, ADU, LCC
Item: Counter
Operation/Procedure
The values of the paper feed related counters are displayed.
Press [COLOR] or [BLACK] button to print. 
 
22-10
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the system configuration
(option, internal hardware).
Section:—
Item: Specifications (Option)
Operation/Procedure
1) The system configuration is displayed. (The model names of
the installed devices and options are displayed.)
2) Change the display with [↑] [↓] buttons.
Press [COLOR] or [BLACK] button to print. 
 
22-11
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the use frequency (send/
receive) of FAX. (Only when FAX is
installed)
Section:FAX
Item: Counter
Operation/Procedure
The values of the FAX send counter and the FAX receive counter
are displayed.
Press [COLOR] or [BLACK] button to print. 
TRAY1 Tray 1 paper feed counter
TRAY2 Tray 2 paper feed counter
TRAY3 Tray 3 paper feed counter
TRAY4 Tray 4 paper feed counter
MFT TOTAL Manual paper feed counter (Total)
MFT HEAVY Manual paper feed counter (Heavy paper)
MFT OHP Manual paper feed counter (OHP)
MFT ENV Manual paper feed counter (Envelope)
LCC Side LCC paper feed counter (A4LCC)
ADU ADU paper feed counter
Item display Display content Content
MACHINE MX-2300G Machine 
MX-2300FG
MX-2700G
MX-2700FG
MX-2300N
MX-2700N
RSPF/DSPF MX-RPX1/
STANDARDDocument feed unit
STAMP AR-SU1 Finisher stamp
DESK MX-DEX1 Desk unit
MX-DEX2
LCC MX-LCX1 Large capacity cassette (Side LCC)
RSPF/DSPF : 00000000
SCAN : 00000000
STAPLER : 00000000
PUNCHER : 00000000
STAMP : 00000000
SIMULATION NO.22-08TEST
ORG./STAPLE COUNTER DISPLAY
CLOSE
SADDLE STAPLER : 00000000
OC OPEN : 00000000
RSPF/DSPF_OPEN : 00000000
OC LAMP TIME : 00000:00
0
TRAY1 : 00000000
TRAY2 : 00000000
TRAY3 : 00000000
TRAY4 : 00000000
MFT TOTAL : 00000000
SIMULATION NO.22-09TEST
PAPER FEED COUNTER DISPLAY
CLOSE
MFT HEAVY : 00000000
MFT OHP : 00000000
MFT ENV : 00000000
LCC : 00000000
ADU : 00000000
1/1
0
PUNCHER MX-PNX1A Punch unit
MX-PNX1B
AR-PN1A
AR-PN1B
FINISHER MX-FNX1 Finisher
MX-FNX2
FAX1 MX-FXX1 FAX kit
FAX2 MX-FLX1 FAX2 line kit
FAX MEMORY AR-MM9 FAX expansion memory
MX-MMX1
HAND SET MX-HNX1 Handset
NETWORK 
SCANNERMX-NSX1 Network scanner expansion kit
PRINTER MX-PBX1 Printer expansion kit
PS MX-PKX1 PS expansion kit
SECURITY MX-FRX1 Security kit
AIM MX-AMX1 Application expansion kit
SDRAM(SYS) *****MB SDRAM capacity
SDRAM(ICU) *****MB SDRAM capacity
HDD *****MB Hard disk capacity
NIC STANDARD NIC
BARCODE AR-PF1 Barcode font
INTERNET-FAX MX-FWX1 Internet Fax expansion kit
FAX OUTPUT FAX print quantity counter (for line 1)
FAX OUTPUT_L2 FAX print quantity counter (for line 2)
FAX SEND FAX send counter
FAX RECEIVED FAX receive counter
SEND IMAGES FAX send quantity counter (for line 1)
SEND IMAGES_L2 FAX send quantity counter (for line 2)
SEND TIME FAX send time
RECEIVED TIME FAX receive time
ACR SEND Number of carrier prefix adding communicationsItem display Display content Content
SIMULATION NO.22-10
MACHINE SYSTEM
TESTCLOSE0
MACHINE:MX-2300G
RSPF/DSPF
:MX-RPX1/STANDARD
STAMP:AR-SU1
DESK
:MX-DEX1
LCC:MX-LCX1PUNCHER
:MX-PNX1A
FINISHER
:MX-FNX1
FA XBñ:MX-FNX1
1/ 3
FA X 2:MX-FLX1
FA X M E M O R Y:AR-MM9
FA X O U T P U T
SIMULATI ONNO.2211TEST
FA XCOUNTERDISPLAY
CLOSE
00000000
9æSEND IMAGES_L2000000009æ
FA X O U T P U T _ L 2
000000009æSEND TIME00000000:00:009æ
FA X S E N D
000000009æRECEIVED TIME00000000:00:009æ
FAX RECEIVED
000000009æACRSEND9æ
SEND IMAGES000000009æ1/1
0
00000000 
						

							MX-2300/2700 N/G  SIMULATION  7 – 23
 
22-12
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the RSPF misfeed positions
and the number of misfeed at each posi-
tion. (When the number of misfeed is con-
siderably great, it can be judged as
necessary for repair.)
Section:RSPF
Item: Function
Operation/Procedure
The history of paper jam and misfeed is displayed.
The misfeed history is displayed sequentially from the latest one.
The max. 50 items are recorded. (The oldest one is sequentially
deleted.) This data can be used to identify the trouble position.
Press [COLOR] or [BLACK] button to print.
List of JAM codes: Refer to 2. Paper JAM code in the [12] OTH-
ERS.
 
22-13
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the operating time of the
process section (OPC drum, DV unit, toner
cartridge).
Section:—
Item: Counter
Operation/Procedure
The rotating time and the print quantity of the process section are
displayed.
Change the display with [↑] [↓] buttons.
Press [COLOR] or [BLACK] button to print. 
 
22-19
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the values of the counters
related to the scan mode and the internet
FAX mode.
Section: Scanner
Item: Counter
Operation/Procedure
Used to display the counter value related to the network scanner. 
Change the display with [↑] [↓] buttons.
Press [COLOR] or [BLACK] button to print.
DRUM CTRG K Drum cartridge print counter (K)
DRUM CTRG C Drum cartridge print counter (C)
DRUM CTRG M Drum cartridge print counter (M)
DRUM CTRG Y Drum cartridge print counter (Y)
DRUM RANGE K Drum cartridge accumulated traveling distance 
(CM)(K)
DRUM RANGE C Drum cartridge accumulated traveling distance 
(CM)(C)
DRUM RANGE M Drum cartridge accumulated traveling distance 
(CM)(M)
DRUM RANGE Y Drum cartridge accumulated traveling distance 
(CM)(Y)
DEVE CTRG K Developer cartridge print counter (K)
DEVE CTRG C Developer cartridge print counter (C)
DEVE CTRG M Developer cartridge print counter (M)
DEVE CTRG Y Developer cartridge print counter (Y)
DEVE RANGE K Developer cartridge accumulated traveling distance 
(CM)(K)
DEVE RANGE C Developer cartridge accumulated traveling distance 
(CM)(C)
DEVE RANGE M Developer cartridge accumulated traveling distance 
(CM)(M)
DEVE RANGE Y Developer cartridge accumulated traveling distance 
(CM)(Y)
TONER MOTOR K Toner motor print counter (K)
TONER MOTOR C Toner motor print counter (C)
CLOSESIMULATIONNO.229Ù12
52(,#/*+5614;#&+52.#;
TESTCLOSE
0


















TONER MOTOR M Toner motor print counter (M)
TONER MOTOR Y Toner motor print counter (Y)
TONER TURN K Toner motor accumulated rotation time (SEC)(K)
TONER TURN C Toner motor accumulated rotation time (SEC)(C)
TONER TURN M Toner motor accumulated rotation time (SEC)(M)
TONER TURN Y Toner motor accumulated rotation time (SEC)(Y)
NET SCN ORG_B/W Network scanner document read quantity 
counter (B/W) (B/W scan job)
NET SCN ORG_CL Network scanner document read quantity 
counter (COLOR) (Color scan job)
NET SCN ORG_2CL Network scanner document read quantity 
counter (2-COLOR) (2-Color scan job)
NET SCN ORG_SGL Network scanner document read quantity 
counter (SINGLE) (Single-color scan job)
INTERNET FAX OUTPUT Number of times of internet FAX output 
INTERNET FAX SEND 
OUTPUTNumber of times of internet FAX send 
INTERNET FAX RECEIVE Number of times of internet FAX receive 
INTERNET FAX SEND Number of times of internet FAX send 
MAIL COUNTER Number of times of E-MAIL send 
FTP COUNTER Number of times of FTP send 
SMB SEND Number of times of SMB send 
USB CNT Number of times of USB storage 
TRIAL MODE_B & C Trial mode counter (B/W & COLOR scan 
job)
SCAN TO HDD_B/W SCAN TO HDD record quantity (B/W)
SCAN TO HDD_CL SCAN TO HDD record quantity (COLOR)
SCAN TO HDD_2CL SCAN TO HDD record quantity (2-COLOR)
SCAN TO HDD_SGL SCAN TO HDD record quantity (SINGLE 
color)
DRUM CTRG K
SIMULATIONNO.2213TEST
PROCESS CARTRIDGE DISPLAY
CLOSE
00000000
:DRUM RANGE K00000000:
DRUM CTRG C00000000:DRUM RANGE C00000000:DRUM CTRG M00000000:DRUM RANGE M00000000:
DRUM CTRG Y00000000:DRUM RANGE Y00000000:
1/2
0
NETSCNORG_2CL00000000:
SIMULATIONNO.2219TEST
NETWORK SCANNER COUNTER DISPLAY
CLOSE
1/4
NETSCNORG_B/W00000000:
NETSCNORG_CL
00000000:
NETSCNORG_SGL
00000000:
INTERNET FAXOUTPUT
00000000: 
						

							MX-2300/2700 N/G  SIMULATION  7 – 24
 
22-90
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to output the various set data lists.
Section:—
Item: Function
Operation/Procedure
Change the display with [↑] [↓] buttons.
Select the print target with the buttons on the touch panel. 
Press [EXECUTE] button to start self print.
* When [C] key, [CA] key, [SYSTEM SETTINGS] key, or [EXE-
CUTE] button is pressed during printing, the operation is termi-
nated.
 
23
 
23-2
Purpose: Adjustment/Setup/Operation data check
Function (Purpose): Used to check the trouble history of paper
jam and misfeed. (If the number of misfeed
and troubles is considerably great, it may
be judged as necessary to repair.)
Section:—
Item: Trouble
Operation/Procedure
Press [EXECUTE] button to execute print of the list.
 
23-80
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the sen-
sors and detectors in the paper feed and
transport section.
Section: Paper feed, transport
Item: Function
Operation/Procedure
Press [EXECUTE] button to execute print of the list.
* When [C] key, [CA] key, [SYSTEM SETTINGS] key, or [EXE-
CUTE] button is pressed during printing, the operation is termi-
nated. 
 
24
 
24-1
Purpose: Data clear
Function (Purpose): Used to clear the jam counter, and the trou-
ble counter. (The counters are cleared after
completion of maintenance.)
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
All custom setting list ALL CUSTOM 
SETTING LISTAll custom setting list
Printer test page PCL SYMBOL SET 
LISTPCL symbol set list
PCL INTERNAL FONT 
LISTPCL internal font list
PCL EXTENDED 
FONT LISTPCL extended font list
PS FONT LIST PS extended font list
PS KANJI FONT LIST PS kanji font list
PS EXTENDED FONT 
LISTPS extended font list
NIC PAGE NIC page
Address registration 
listINDIVIDUAL LIST One-touch address list
GROUP LIST Group list
PROGRAM LIST Program list
MEMORY BOX LIST Memory box list
ALL SENDING 
ADDRESS LISTAll address registration 
list
Document filing 
folder listDOCUMENT FILING 
FOLDER LISTFolder list
System setting list ADMIN. SETTINGS 
LIST (COPY)Copy
ADMIN. SETTINGS 
LIST (PRINT)Printer
ADMIN. SETTINGS 
LIST (IMAGE SEND)FAX/Image send
ADMIN. SETTINGS 
LIST (DOC FILING)Document filing
ADMIN. SETTINGS 
LIST (SECURITY)Security
ADMIN. SETTINGS 
LIST (COMMON)Common
ALL ADMINISTRATOR 
SETTINGS LISTAll system setting list
Receive rejection 
number tableANTI JUNK FAX 
NUMBER LISTReceive rejection 
number table
Receive rejection/
allow address/
domain table ANTI JUNK MAIL/
DOMAIN NAME LISTReceive rejection/allow 
address/domain table 
Transfer to Email 
table listINBOUND ROUTING 
LISTTransfer to Email table 
list
Transfer to 
Administrator listDOCUMENT ADMIN 
LISTTransfer to 
Administrator list
Web setting list WEB SETTING LIST Web setting list
Meta data set list METADATA SET LIST Meta data set list
SIMULATION NO.22-90TES
LIST PRINT
1/4EX
0
CLTEST
ALL CUSTOM SETTING LISTPCL SYMBOL SET LIST
PCL INTERNAL FONT LISTPCL EXTENDED FONT LIST
PS KANJI FONT LIST
EXECUTE
0
CLOSE
PS EXTENDED FONT LISTNIC PAGE PS FONT LIST
SIMULATIONNO.23-02TEST
JAM/TROUBLE DATA PRINT MODE
EXECUTE
0CLOSE
PRESS[EXECUTE] TO PRINT THE JAM/TROUBLEPRINT
SIMULATIONNO.23-80TEST
DATA PRINT MODE9ÔPA P E RFEED9Õ
PA P E RFEEDTIMELIST
1/1EXECUTE
0CLOSE