Sanyo Projector Plc Xw60 User Manual
Have a look at the manual Sanyo Projector Plc Xw60 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
1
Basic OperationBasic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
M e n u . R e f e r t o t h e f o l l o w i n g p a g e s r e g a r d i n g e a c h
adjustment and setting procedures.Press the Point
7 8 buttons to select a Menu icon to
adjust and press the Point ed buttons to select an
item to adjust.
Press the SELECT button to show the item data. To
adjust the data, press the Point
7 8 buttons. Refer to
the following pages for each adjustment.
To close the On-Screen Menu, press the MENU button
again. Press the MENU button to display the On-Screen
Menu.
✔ Note:
The selected item is not active until the SELECT
button is pressed.
1
2
3
Top Control
SELECT button
POINT buttons
Remote Control
MENU button
Menu bar Pointer
(red framed )Menu icon
Item data
P r e s s t h e P o i n t
7 8
buttons to adjust the
value.
SELECT
button
Pointer (red framed )
Press the Point ed buttons to
move the pointer.
Item
On-Screen Menu
Quit
Exit this menu.
MENU button SELECT buttonPOINT buttons
(outer ring)
Basic Operation
Menu Bar
PC System Menu
U s e d t o s e l e c t
computer system.
(p.27)
Setting Menu
U s e d t o s e t t h e
p r o j e c t o r ' s o p e r a t i n g
configurations.
(p.45-56)
Image Select Menu
U s e d t o s e l e c t a n
i m a g e l e v e l a m o n g
D y n a m i c , S t a n d a r d ,
R e a l , B l a c k b o a r d
( G r e e n ) , C o l o r b o a r d
and Image 1 ~ 4. (p.31)
For computer source
Guide Window
Show the selected
M e n u o f t h e
On-Screen Menu.
Screen Menu
Used to adjust size of
image. [Normal / True
/ Wide / Full / Custom
/ D i g i t a l z o o m + / – ]
(p.34-36)
For detailed functions, see Menu Tree on pages 66-68.
Image Adjust Menu
Used to adjust computer
i m a g e . [ C o n t r a s t /
Brightness / Color temp.
/ White balance (R/G/B)
/ Sharpness / Gamma]
(p.33-34)
Sound Menu
Used to adjust the
volume or mute the
sound. (p.24)
PC Adjust Menu
U s e d t o a d j u s t
parameters to match
w i t h i n p u t s i g n a l
format. (p.28-30)
Input Menu
U s e d t o s e l e c t
i n p u t s o u r c e
e i t h e r C o m p u t e r
or Video. (p.26)
For video source
Input Menu
U s e d t o s e l e c t i n p u t
source either Video or
Computer. (p.37, 38)
Image Select Menu
U s e d t o s e l e c t a n i m a g e l e v e l a m o n g
Dynamic, Standard, Cinema, Blackboard
(Green), Colorboard and Image 1 ~ 4. (p.40)
Screen Menu
U s e d t o s e t s i z e o f
image to Normal, Wide
or Custom. (p.44)
AV System Menu
Used to select system
o f s e l e c t e d v i d e o
source. (p.39)
Image Adjust Menu
U s e d t o a d j u s t p i c t u r e i m a g e .
[Contrast / Brightness / Color / Tint
/ C o l o r t e m p . / W h i t e b a l a n c e ( R /
G/B) / Sharpness / Gamma / Noise
reduction / Progressive ] (p.42-43)S a m e f u n c t i o n
a s c o m p u t e r
menu.
S a m e f u n c t i o n a s
menu for computer
source.
Basic Operation
✔ Note:
I t e m s w i l l b e s a m e a s t h e i t e m s i n v i d e o s o u r c e
when 480i, 575i, 480p, 575p, 720p, 1035i or 1080i is
selected.
Basic OperationBasic Operation
Rotate the Zoom Lever to zoom in and out.
Rotate the Focus Lever to adjust the projected picture
focus.
Zoom and Focus Adjustment
Zoom Lever
(Rear)Focus Lever
(Front)
If a projected picture still has keystone distortion after
pressing the AUTO SETUP button on the top control,
correct the image manually as follows:
Press the KEYSTONE button on the remote control. The
keystone dialog box appears.
Correct keystone distortion by pressing the Point
ed buttons. Keystone adjustment can be memorized. (p.47)
Reduce the upper width
with Point e button. Reduce the lower width
with Point d button.
Keystone Correction
•
T h e a r r o w s a r e w h i t e w h e n t h e r e i s n o
correction.
•
The direction of the arrow being corrected turns
red.
•
T h e a r r o w s d i s a p p e a r a t t h e m a x i m u m
correction.
•
I f y o u p r e s s t h e K E Y S TO N E b u t t o n o n t h e
remote control once more while the keystone
d i a l o g b o x i s b e i n g d i s p l a y e d , t h e k e y s t o n e
adjustment is canceled.
•
The adjustable range is limited depending
on the input signal.
Remote Control
Top Control
KEySTONE button
POINT ed buttons
POINT ed buttons
Auto setup function is provided to automatically execute
the setting of Auto setup (includes Input search, Auto PC
adj. and Auto Keystone functions) in the setting menu by
just pressing the AUTO SETUP button on the top control.
Refer to page 46 for the setting of the Auto setup function.
Auto setup functionTop Control
AUTO SETUP button
4
Basic Operation
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog
box appears on the screen for a few seconds.
Press the MUTE button on the remote control to cut off the
sound. To restore the sound to its previous level, press
the MUTE button again or press the VOLUME +/– buttons.
Mute function is also effective for AUDIO OUT jack. Volume
Mute
Direct Operation
Sound Adjustment
1
2
Press the MENU button to display the On-Screen
Menu. Press the Point 7 8 buttons to move the red
framed pointer to the Sound Menu icon.
Press the Point 7 8 buttons to cut off the sound. Dialog
box display changes to "On" and the sound is cut off. To
restore the sound to its previous level, press the Point
7 8
buttons again.
Press the Point ed buttons to move the red framed
pointer to the item that you want to select, and then
press the SELECT button.
Volume
Mute
Press the Point 8 button to turn up the volume, and press
the Point 7 button to turn down the volume.
Menu Operation
Remote Control Operation
For some frequently used operations, using the remote
control is advisable.
Just pressing one of the buttons enables you to make the
operation, and no need for calling up the On-Screen Menu.
Press the FREEZE button on the remote control to freeze
the picture on the screen. To cancel the Freeze function,
press the FREEZE button again or press any other button. FREEZE button
Press the COMPUTER or VIDEO button on the remote
control to select the input source. For more detail, see
pages 26, 37 and 38. COMPUTER/VIDEO buttons
Remote Control
COMPUTER/
VIDEO buttons
✔ Note:
S e e t h e n e x t p a g e f o r t h e o t h e r
buttons.
FREEZE button
Remote Control
VOL+ button
VOL- button
MUTE button
Top Control
VOLUME+/- buttons
Approximate level
of the volume.
Press the MUTE button to set the Mute function
On/Off. The display disappears after 4 seconds.
Approximate level of
the volume.
Exit the Sound Menu.
Sound Menu
S o u n d M e n u
icon
Basic Operation
5
Basic OperationBasic Operation
black out ➜ the captured image ➜ normal ➜ • • • • •
Press the NO SHOW button on the remote control to black
out the image. To restore to normal, press the NO SHOW
button again or press any other button. When a projected
image is captured and set as "User" in the Logo selection
(p.48), the screen changes each time you press the NO
SHOW button as follows. NO SHOW button
P r e s s t h e A U TO P C b u t t o n o n t h e r e m o t e c o n t r o l t o
operate the Auto PC function. For more detail, see page
28. AUTO PC button
Press the D.ZOOM buttons on the remote control to zoom
in and zoom out the images. For more detail, see page
36. D
.ZOOM buttons
Press the P-TIMER button on the remote control. The
timer display "00 : 00" appears on the screen and the
timer starts to count time (00 : 00 ~ 59 : 59).
To stop the P-Timer, press the P-TIMER button. Press
t h e P - T I M E R b u t t o n a g a i n , t h e n t h e P - t i m e r d i s p l a y
disappears. P-TIMER button
Press the IMAGE button on the remote control to select
a desired image level of the screen. For more detail, see
pages 31 and 40. IMAGE button
For detail, see page 23. KEySTONE button
LAMP CONTROL button
Press the LAMP CONTROL button on the remote control
to select the lamp mode for changing the brightness of the
screen.
Normal . . .normal brightness
Auto . . . . . brightness according with the input signal
Eco
........... l o w e r b r i g h t n e s s r e d u c e s t h e l a m p
power consumption and extends the
lamp life.
Remote Control
D .ZOOM buttons
NO SHOW button AUTO PC button
✔ Note:
See the previous page for the other
buttons.
KEySTONE button
(See p.23)
POINT
ed buttons
The message disappears after 4 seconds.
P-Timer display LAMP CONTROL button
P-TIMER button
IMAGE button
VOLUME +/- buttons
(See p.24.)
6 Computer Input C h o o s e e i t h e r R G B o r C o m p u t e r 2 b y p r e s s i n g t h e COMPUTER button on the remote control. Before using C O M P U T E R b u t t o n , c o r r e c t i n p u t s o u r c e s h o u l d b e selected through Menu operation as described below. Input Source Selection Direct Operation RGB COMPUTER button ✳ See Notes at the bottom of this page. ✳ Remote Control COMPUTER button Computer Input Menu Input Menu M o v e t h e p o i n t e r ( r e d arrow) to Computer 1 and press the SELECT button. Input Menu icon M o v e t h e p o i n t e r ( r e d arrow) to Computer 2 and press the SELECT button.Move the pointer to RGB a n d p r e s s t h e S E L E C T button. Source Select Menu Computer 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Input Menu icon.1 Press the Point ed buttons to move the red arrow pointer to either Computer 1 or Computer 2, and then press the SELECT button.2 After the Source Select Menu appeared for Computer 1 , m o v e t h e p o i n t e r t o R G B a n d t h e n p r e s s t h e SELECT button.3 Menu Operation ✔ Notes: • When the Input Search function is set On1 or On2, the input signal will be searched automatically (p.46) • Computer 2 is not displayed when the COMPUTER IN 2/MONITOR OUT terminal is set as Monitor out. (p.50) • Computer 2 (COMPUTER IN 2 / MONITOR OUT) can accept only RGB signal. Computer Input
7 Computer Input Computer Input Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is s\ hown on page 70) One of the following messages may appear when: The projector cannot recognize the connected signal conforming to the provided PC Systems. The message "Auto" is displayed on the PC System Menu icon and the Auto PC Adjustment function works to display proper images. If the image is not projected properly, a manual adjustment is required. (p.29-30) There is no signal input from computer. Check the connection between your computer and the projector. (See "Troubleshooting" on pages 64-65.) Auto The preset system is manually adjusted in the PC Adjust Menu. The adjusted data can be stored in Mode 1 ~ 5. (p.29-30) P C S y s t e m s p r o v i d e d i n t h i s p r o j e c t o r i s c h o s e n . T h e p r o j e c t o r c h o o s e s a p r o p e r system provided in the projector and displays it. *Mode 1 and SVGA 1 are examples. Mode 1 SVGA 1 ----- Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the PC System Menu icon. Press the Point ed buttons to move the red arrow pointer to the system that you want to set, and then press the SELECT button. PC system can also be selected manually. Selecting Computer System Manually 1 2 T h e A u t o P C A d j u s t m e n t function operates to adjust the projector. PC System Menu The PC System Menu icon Selected system is displayed. S y s t e m s o n t h i s d i a l o g box can be selected. PC System Menu Custom Mode (1 ~ 5) set in the PC Adjust Menu. (p.30)
8 Computer Input Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adjustment The Auto PC adjustment function can be operated directly by pressing the AUTO PC button on the remote control unit. Direct OperationRemote Control AUTO PC button Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to PC Adjust Menu icon. Press the Point ed buttons to move the red framed p o i n t e r t o A u t o P C A d j . i t e m a n d t h e n p r e s s t h e SELECT button twice. Auto PC Adj . Menu Operation 1 2Move the red framed pointer to the Auto PC Adj. item and press the SELECT button. "Please wait..." message appears w h i l e A u t o P C a d j u s t m e n t i s i n process. PC Adjust Menu PC Adjust Menu icon To store adjustment parameters Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in the PC System Menu (p.27). See "Store" on page 30. ✔ Notes: • Fine sync, Total dots, Horizontal, and Vertical of some computers cannot be fully adjusted with this Auto PC Adjustment function. When the image is not provided properly with this operation, manual adjustments are required. (p.29-30) • The Auto PC Adjustment cannot be operated when 4 8 0 i , 5 7 5 i , 4 8 0 p , 5 7 5 p , 7 2 0 p , 1 0 3 5 i , o r 1 0 8 0 i i s selected in the PC System Menu. (p.27) Computer Input
Computer InputComputer Input Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the PC Adjust Menu icon. Press the Point ed buttons to move the red framed pointer to the item that you want to adjust and then press the SELECT button to display the adjustment dialog box. Press the Point 7 8 buttons to adjust the value. Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 2 Eliminate flicker from the image displayed. Press the Point 7 8 buttons to adjust the value. (From 0 to 31.) Fine sync Adjust the number of total dots in one horizontal period. Press the Point 7 8 buttons to adjust number to match your PC image. Total dots Press the Point 7 8 buttons to adjust the horizontal picture position. Horizontal Press the Point 7 8 buttons to adjust the vertical picture position. Vertical P r e s s t h e S E L E C T b u t t o n t o s h o w H - s y n c f r e q . a n d V-sync freq. of the connected computer. Current mode Adjust clamp level. When the image has dark bars, try this adjustment.Clamp M o v e t h e r e d f r a m e d pointer to an item and press the SELECT button. PC Adjust MenuPC Adjust Menu icon P r e s s t h e S E L E C T button at this item to adjust other items. Press the Point 7 8 buttons to adjust the value. Status (Stored/Free) of the selected Mode. Selected Mode Press the SELECT button at the Current mode item to show the information of the connected computer.
0
Computer Input
Adjust the horizontal area displayed by this projector.
Press the Point 7 8 buttons to decrease/increase the
value. Display area H
Adjust the vertical area displayed by this projector. Press
the Point 7 8 buttons to decrease/increase the value.
Display area V
Reset
Store
Exit the PC Adjust Menu.
Quit
To store adjusted data, move the red framed pointer to the
Store item and then press the SELECT button. Move the
red arrow pointer to any of Mode 1 to 5 in which you want
to store and then press the SELECT button.
To reset the adjusted data, select Reset and press the
S E L E C T b u t t o n . T h e c o n f i r m a t i o n b o x a p p e a r s a n d
then select [Yes]. All adjustments return to their previous
figures.
Mode free
To clear the stored data, move the red framed pointer to
the Mode free item and then press the SELECT button.
Move the red arrow pointer to the Mode that you want to
clear and then press the SELECT button.
✔ Note:
Display area (H/V) cannot be selected when 480i,
575i, 480p, 575p, 720p, 1035i, or 1080i is selected in
the PC System Menu (p.27).
Vacant Mode Va l u e s o f " To t a l d o t s " ,
"Horizontal", "Vertical",
" D i s p l a y a r e a H " a n d
"Display area V".
Close this dialog box.
To store adjusted data
To clear adjusted data
This Mode has stored parameters.
M o v e t h e r e d f r a m e d
p o i n t e r t o a n i t e m a n d
press the SELECT button.
Computer Input