Sanyo Projector Plc Xw60 User Manual

							41
Video Input
User preset image in the Image Adjust Menu. (p.43)Image 1 ~ 4
M o v e   t h e   r e d   f r a m e d 
p o i n t e r  t o  t h e  l e v e l  a n d 
press the SELECT button.
The level being selected.
Image Select Menu
Image Select Menu icon
Colorboard
Press  the  MENU  button  to  display  the  On-Screen 
Menu.    Press  the  Point 7  8  buttons  to  move  the  red 
framed pointer to the Image Select Menu icon.
Press  the  Point ed  buttons  to  move  the  red  framed 
pointer to the level that you want to set and then press 
the SELECT button.
Menu Operation
1
2
Normal picture level preset on this projector.
Standard
Picture level with improved halftone for graphics.Cinema
P i c t u r e  l e v e l  s u i t a b l e  f o r  t h e  i m a g e  p r o j e c t e d  o n  a 
blackboard.  See above for further description.Blackboard (Green)
Picture level suitable for viewing picture in a bright room.
Dynamic
At  the  time  of  simple  projection  on  the  colored  wall,  you 
can get the close color image to the color image projected 
on  a  white  screen  by  selecting  the  similar  color  to  the 
wall  color  from  the  preset  four  colors.  Press  the  SELECT 
button to choose the color. 
Video Input 
						

							4
Video Input
Press  the  MENU  button  to  display  the  On-Screen 
Menu.    Press  the  Point 7  8  buttons  to  move  the  red 
framed pointer to the Image Adjust Menu icon.
Press  the  Point ed  buttons  to  move  the  red  framed 
pointer  to  the  item  that  you  want  to  adjust,  and  then 
press  the  SELECT  button.    The  level  of  each  item  is 
displayed.  Adjust each level by pressing the Point 
7 8 
buttons.
Image Level Adjustment
1
2
Image Adjust Menu
Press  the  Point 7  button  to  decrease  the  contrast  and  the 
Point 8 button to increase contrast. (From 0 to 63.)
Press  the  Point 7  button  to  adjust  the  image  darker  and 
the Point 8 button to adjust the image brighter. (From 0 to 
63.) Contrast
Brightness
Press  the  Point 7  button  to  lighten  the  red  tone  and  the 
Point 8 button to deepen the red tone. 
(From 0 to 63.) White balance (Red)
Press the Point 7 button to lighten the green tone and the 
Point 8 button to deepen the green tone. 
(From 0 to 63.) White balance (Green)
Press  the  Point 7  button  to  lighten  the  blue  tone  and  the 
Point 8 button to deepen the blue tone. 
(From 0 to 63.) White balance (Blue)
Press  the  Point 7  button  or  the  Point 8  button  for  Color 
temp. level that you want to select. 
(XLow, Low, Mid, or High)  Color temp
  .
Press  the  Point 7  button  to  lighten  the  color  and  the  Point 8 button to deepen the color. (From 0 to 63.)
Press  the  Point 7  8  buttons  to  obtain  a  proper  color.  
(From 0 to 63.) Color
Tint
✔ Notes:
  • The Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N.
  • After adjusting any of the White balance Red, Green, or Blue, the Color temp. changes to "Adj.".
P r e s s  t h e  P o i n t 7  8 b u t t o n s  t o  a d j u s t  t h e 
value.
P r e s s   t h e   S E L E C T 
button  at  this  item  to 
display other items.
P r e s s   t h e   S E L E C T 
b u t t o n  a t  t h i s  i t e m  t o 
display previous items.
M o v e   t h e   r e d   f r a m e d  
pointer  to  the  item  to  be 
selected  and  then  press 
the SELECT button.
Image Adjust Menu icon
Video Input 
						

							4
Video InputVideo Input
To  reset  the  adjusted  data,  select  Reset  and  press  the 
SELECT  button.    The  confirmation  box  appears  and  then 
select  [Yes].    All  adjustments  returns  to  their  previous 
figures.
Reset
Press  the  Point 7  8  buttons  to  obtain  better  balance  of 
contrast. (From 0 to 15.) Gamma
Press the Point 7 button to soften the image and the Point 8 button to sharpen the image. (From 0 to 15.)Sharpness
To  store  the  adjusted  data,  select  Store  and  press  the 
SELECT  button.    Select  a  level  from  Image  1  to  4  with 
the  Point 
ed  buttons  and  press  the  SELECT  button.    A 
confirmation box appears and then select [Yes].
Stored  data  can  be  called  up  by  selecting  "Image"  in  the 
Image Level Selection on page 40.
Store
Exit the Image Adjust Menu.
Quit
✔ Note:
    Noise  reduction  and  Progressive  cannot  be  selected 
when  480p,  575p,  720p,  1035i,  or  1080i  is  selected. 
(p.39)
Interlaced  video  signal  can  be  displayed  in  a  progressive 
picture.  Select one of the following.
  Of
f  . . . .  disabled.
  L1
. . . . .  Select "L1" for an active picture.
  L2
. . . . .  Select "L2" for a still picture.
  Film
  . . .  S
e l e c t  " F i l m "  f o r  w a t c h i n g  a  f i l m .  W i t h  t h i s 
function,  the  projector  reproduces  pictures 
faithful to the original film quality.
Progressive
Noise  reduction
Noise  interference  on  the  screen  can  be  reduced.    Select 
one of the following to get smoother images.
 
Of
f  . . . .  disabled.
  L1
. . . . .  lower reduction 
  L2
. . . . .  higher reduction
  
Image Level Menu
Move the red framed pointer 
to  an  image  item  to  be  set 
and  then  press  the  SELECT 
button.
Store item
T h e   c o n f i r m a t i o n   b o x 
appears  and  then  select 
[Yes]. 
						

							44
Video Input
This projector has the picture screen resize function, which enables you\
 to customize the image size.
Press  the  MENU  button  to  display  the  On-Screen 
Menu.    Press  the  Point 7  8  buttons  to  move  the  red 
framed pointer to the Screen Menu icon.
Press  the  Point ed  buttons  and  move  the  red  framed 
pointer to the function that you want to select and then 
press the SELECT button.
Provide the image at a wide screen ratio of 16:9. Wide
Provide the image at a normal video aspect ratio of 4:3.Normal
Screen Size Adjustment
✔ Notes:
  •  Wide  cannot  be  operated  when  720p, 
1035i,  or  1080i  is  selected  in  the  AV 
System Menu (p.39).
• 

  When no signal is detected, "Normal" is 
set  automatically  and  the Aspect  dialog 
box disappears.
• 

  The adjustable range for Scale H/V and 
Position H/V is limited depending on the 
input signal.
1
2
Move  the  red  framed  pointer  to  a 
function  and  press  the  SELECT 
button.
Screen Menu
Screen Menu icon
Adjust the screen scale and position manually with this 
function.
Press the SELECT button at Custom and the "Custom" is 
displayed on the screen for a few seconds and then the 
Aspect dialog box appears.
  Scale H/V  ..................  Adjust the Horizontal/V

ertical 
screen scale.
  H&V  ...........................  When set to "On", the aspect 
ratio is fixed. The "Scale V" 
appears dimmed and becomes 
unavailable. Adjust the "Scale 
H", then the screen scale is 
automatically modified based on 
the aspect ratio. 
  Position H/V  .............. Adjust the Horizontal/V

ertical 
screen position.
  Common  ...................  Save the adjusted scale to all 
the inputs. Press the SELECT 
button at Common to display a 
confirmation box. To save the 
scale, press the SELECT button at 
"Yes". When Custom is selected, 
the saved scale is used.
  Reset  .........................  Reset the all adjusted values. 
Press the SELECT button at 
Reset to display a confirmation 
box. To reset, press the SELECT 
button at "Yes".
Custom
Press the SELECT 
button at Common 
or Reset, to display a 
confirmation box.
Setting 
						

							45
Video InputSetting
Press  the  MENU  button  to  display  the  On-Screen 
Menu.    Press  the  Point 7  8  buttons  to  move  the  red 
framed pointer to the Setting Menu icon.
Language
The  language  used  in  the  On-Screen  Menu  is  available  in 
English,  German,  French,  Italian,  Spanish,  Portuguese, 
Dutch,  Swedish,  Finnish,  Polish,  Hungarian,  Romanian, 
Russian, Chinese, Korean, or Japanese.
Press  the  Point ed  buttons  to  move  the  red  framed  
pointer to the item that you want to set and then press 
the SELECT button. The Setting dialog box appears.
Setting
This  projector  has  Setting  menu  that  allows  you  to  set  up 
the other various functions described as follows:
1
2Set the red framed pointer 
to  the  item  and  press  the 
SELECT button.
P r e s s  t h e  S E L E C T 
button  at  Language 
item,  the  Language 
Menu appears.
Setting Menu (Language)
Setting Menu icon
Press  the  SELECT 
button  at  this  item 
to  display  the  other 
languages.
See the next pages for other items. 
						

							46
Auto setup
S e l e c t   A u t o   s e t u p 
a n d  t h i s  b o x  a p p e a r s . 
C h o o s e   t h e   d e s i r e d 
setting  for  Input  search, 
Auto  keystone  and  Auto 
PC adj. with the Point 7 
8 buttons.
T h i s  f u n c t i o n  e n a b l e s  I n p u t  s e a r c h ,  A u t o  K e y s t o n e 
correction  and Auto  PC  adjustment  by  pressing  the AUTO 
S E T U P  b u t t o n  o n  t h e  t o p  c o n t r o l .  S e t t i n g s  f o r  t h o s e 
functions can be altered as follows:
Input search     ✳
This  function  detects  the  input  signal  automatically.  When 
finding  a  signal,  the  search  will  stop.    Use  the  Point 
7  8 
buttons to select one of the following.
  Of
f  . . . . Input search does not work.
  On1
  . . . Input search works under the situation below.
 

  •  When pressing the AUTO SETUP button on the top 
       control.
    • When pressing the COMPUTER button or VIDEO 
       button on the remote control.
  On2
  . . . Input search works under the situation below.
 

  •  When pressing the POWER ON/STAND-BY button on 
       the top control or on the remote control.
    •  When pressing the AUTO SETUP button on the top 
       control.
  •  When  pressing  the  COMPUTER  button  or  VIDEO 
button on the remote control.
 

  •  When missing the current input signal.  
 
✳
 
  • If the No show or Freeze function is active, cancel it to 
       activate the Input search. It is also unavailable when 
       On-Screen menu is displayed
.
  •

  While  Input  Search  is  set  On1  or  On2,  the  status  of   
Input  and  Lamp  mode  are  displayed  every  time  the 
signal is switched.
  •

  The signal input from S-VIDEO can not be detected.
  •  If  any  of  the  COMPUTER  or  VIDEO  button  on  the 
remote  control,  or  AUTO  SETUP  button  on  the  top 
control  is  pressed  while  Input  search  is  on,  Input 
search will stop.
Auto PC 
 Adj .
On  . . . . Enables Auto PC Adjustment when pressing the             
            

  AUTO SETUP button on the top control.
Off  . . . . Disables Auto PC Adjustment.
Auto Keystone  Auto . . . Always works and corrects keystone distortion   
               according to the projector's tilt.
 
Manual  . Works only when pressing the AUTO SETUP  
                  button on the top control. Off  . . . . Disables Auto Keystone.
✔Notes:
  • Input  search,  Auto  PC  Adj.  and  Auto 
Keystone  cannot  be  set  "Off"  at  the 
same time.
  •
  Auto  Keystone  adjusts  automatically 
by  pressing  the  AUTO  SETUP  button 
either  it  is  set  on  "Auto"  or  "Manual"  in 
setting menu.
  •

  A u t o   K e y s t o n e   c o r r e c t s   v e r t i c a l 
distortion  only,  not  correct  horizontal 
distortion.
  •

  T h e   A u t o   K e y s t o n e   c a n n o t   w o r k 
when  Ceiling  feature  is  set  "On"  in  the 
Setting menu (p.50).
  •

  P e r f e c t   c o r r e c t i o n   o f   t h e   i m a g e 
distortion  cannot  be  ensured  with  the 
Auto  setup  function.  If  the  distortion  is 
not  corrected  properly  by  pressing  the 
AUTO  SETUP  button,  adjust  manually 
b y  p r e s s i n g  t h e  K E Y S TO N E  b u t t o n 
o n  t h e  r e m o t e  c o n t r o l  o r  s e l e c t i n g 
Keystone  in  the  Setting  menu  (p.23, 
47).
  •

  Fine  sync,  Total  dots,  Horizontal  and 
Vertical  position  of  some  computers 
cannot  be  fully  adjusted  with  the  Auto 
P C  A d j u s t m e n t  f u n c t i o n .  W h e n  t h e 
i m a g e  i s  n o t  p r o v i d e d  p r o p e r l y  w i t h 
this  operation,  manual  adjustments  are 
required (p.29–30).
SettingSetting 
						

							47
Setting
Blue back
Press  the  Point 7  8  buttons  to  switch  On/Off.    When  this 
function  is  "On",  a  blue  image  is  displayed  while  the  input 
signal is not detected. 
Keystone
This  function  corrects  distortion  of  a  projected  image. 
Select  either  Store  or  Reset  with  the  Point 7  8  buttons, 
and  then  press  the  SELECT  button.    The  keystone  dialog 
box appears.  Correct keystone with the Point 
ed buttons. 
(p.23)
  Store
  . . . .  store 
 the keystone correction even when the 
AC power cord is unplugged.
  Reset
 . . . .  r
eset  the  keystone  correction  when  the  AC 
power cord is unplugged.
Display
Press the Point 7 8 buttons to switch On/Off. This function 
decides to display On-Screen Displays.
On . . . . . . . . . . . . .  S
 h o w  a l l  t h e  O n - S c r e e n  D i s p l a y s . 
U s e  t h i s  f u n c t i o n  w h e n  y o u  w a n t 
t o  p r o j e c t  i m a g e s  a f t e r  t h e  l a m p 
b e c o m e s  b r i g h t  e n o u g h .    F a c t o r y 
default setting is this mode.
Countdown off  . . .  S
h o w  t h e  i n p u t  i m a g e  i n s t e a d  o f 
the  countdown  when  turning  on  the 
projector.  Use this function when you 
want  to  project  the  image  as  early  as 
possible  even  when  the  lamp  is  not 
bright enough.
Off . . . . . . . . . . . . .  D
 o  n o t  s h o w  O n - S c r e e n  D i s p l a y s , 
except;
  ●
  On-Screen Menu 
  ●  "Power of f?" message 
  ●  P-Timer 
  ●  "No signal" message for Power management item 
(p.51)
  ●  "Please wait..." message
  ●  Arrows for panning mode in the Screen Menu (p.34)
Setting 
						

							48
Setting
Logo select
This function decides the start-up display as follows:
 User
. . . .  the image you captured
  Default
. . the factory-set logo
  Of

f  . . . . .  countdown only
Logo (Logo and Logo PIN code lock settings)
This function allows you to customize the screen logo with 
Logo select, Capture, and Logo PIN code lock functions.
✔ Note:
    When  On  is  selected  in  Logo  PIN  code  lock  function, 
L o g o  s e l e c t  a n d  C a p t u r e  f u n c t i o n s  c a n n o t  b e 
selected.
Logo select
Capture
This  function  enables  you  to  capture  the  image  being 
projected  and  use  it  for  a  start-up  display  or  interval  of 
presentations.
After  capturing  the  projected  image,  go  to  the  Logo 
select  function  and  set  it  to  "User".    Then  the  captured 
image  is  displayed  when  turning  on  the  projector  next 
time or pressing the NO SHOW button. (p.25) 
To  capture  the  image,  select  [Yes].    To  cancel  the 
Capture function, select [No].
✔ Notes:
  • Before  capturing  an  image,  select  Standard  in  the 
Image  Select  Menu  to  capture  a  proper  image. 
(p.32, 40.)
  •

  A  signal  from  a  computer  can  be  captured  up  to 
XGA  (1024x768).    A  signal  from  video  equipment 
c a n  b e  c a p t u r e d  e x c e p t  f o r  7 2 0 p ,  1 0 3 5 i ,  a n d 
1080i.
  •

  When  capturing  the  image  that  has  been  adjusted 
by  the  Keystone  function,  the  adjustment  data  is 
automatically  reset  and  the  projector  captures  an 
image without keystone adjustment.
  •

  When  the  Logo  PIN  code  lock  function  is  "On", 
Capture menu cannot be selected.
  •

  W h e n  s t a r t i n g  t o  c a p t u r e  a  n e w  i m a g e ,  t h e 
previously  stored  image  is  cleared  even  if  you 
cancel the capturing.
  •

  "User"  cannot  be  selected  when  the  image  is  not 
captured.
Select  [Yes]  to  capture  the 
projected image.
S e l e c t  [ Ye s ]  t o  s t o p 
capturing.
Capture
Setting 
						

							4
SettingSetting
This  function  prevents  an  unauthorized  person  from 
changing the screen logo.
 Of f ......  the  screen  logo  can  be  changed  freely  from 
the Logo select menu.  (p.48)
  On
 ......  the  screen  logo  cannot  be  changed  without 
the Logo PIN code.
If  you  want  to  change  the  Logo  PIN  code  lock  setting, 
enter  a  Logo  PIN  code  along  the  following  steps.    The 
initial Logo PIN code is set "4321" at the factory.
Logo PIN code lockLogo PIN code lock
To Enter the Logo PIN code
Select  a  number  by  pressing  the  Point ed  buttons.  And 
then  press  the  Point 8  button  to  fix  the  number  and  move 
the  pointer.    The  number  changes  to  " ✳".    If  you  fixed 
an  incorrect  number,  move  the  pointer  to  the  number 
you  want  to  correct  by  pressing  the  Point 
7  button,  and 
then  select  the  correct  number  by  pressing  the  Point ed 
buttons.
Repeat this step to complete entering a four-digit number.
After  entering  the  four-digit  number,  move  the  pointer  to 
"Set"  by  pressing  the  Point 
8  button.    Press  the  SELECT 
button  so  that  you  can  change  the  Logo  PIN  code  lock 
setting.
If  you  entered  an  incorrect  Logo  PIN  code,  "Logo  PIN 
code"  and  the  number  (✳✳✳✳)  turns  red.    Enter  a  correct 
Logo PIN code all over again.
To Change the Logo PIN code
Logo  PIN code  can  be  changed  to  your  desired  four-digit 
number.    Select  "Logo  PIN  code  change"  with  the  Point 
d  button  and  press  the  SELECT  button.    Set  a  new  Logo 
PIN code.
Be  sure  to  note  the  new  Logo  PIN  code  and  keep  it  at 
hand.  If you lost the number, you could no longer change 
t he  Logo  PIN  code  setting.    For  details  on  PIN  code 
setting,  refer  to  relevant  instructions  of  the  PIN  code  lock 
function on pages 53 and 54.
CAUTION :
WHEN  yOU  HAVE  CHANGED   THE LOGO  PIN  CODE, 
WRITE  DOWN  THE  NEW  PIN  CODE  IN  COLUMN  OF  
THE   LOGO  PIN CODE  NO .  MEMO  ON  PAGE   74, AND 
KEEP  IT  SECUREL y .  SHOULD  THE   LOGO  PIN CODE  
BE  LOST  OR FORGOTTEN,  THE PROjECTOR  CAN NO 
LONGER BE OPERATED . Logo PIN code lock Dialog Box
After  a  correct  Logo  PIN  code  is  entered,  the 
following dialog box appears.
Select On/Off by pressing the Point 
7 8 buttons or 
change the Logo PIN code. 
						

							50
Setting
Ceiling
When  this  function  is  "On",  the  picture  is  top/bottom  and 
left/right  reversed.    This  function  is  used  to  project  the 
image from a ceiling mounting the projector.Rear
When this function is "On", the picture is left/right reversed.  
T h i s  f u n c t i o n  i s  u s e d  t o  p r o j e c t  t h e  i m a g e  t o  a  r e a r 
projection screen.
Ceiling 
Rear 
Terminal
The  COMPUTER  IN  2/MONITOR  OUT  terminal  on  the 
back  of  the  projector  is  switchable  for  computer  input 
or  monitor  output.  (See  page  9)    Select  Computer  2  or 
Monitor Out with the Point 
7 8 buttons.
  Computer 2   . . . . . . computer input
  Monitor Out
  . . . . . . monitor out
Terminal function is not available when selecting Computer 
2  to  the  input  source.    Change  the  input  source  to  the 
others  (Computer1  or  Video)  so  that  the  Terminal  function 
will be available. (p.26, 37, 38)
Setting
Standby mode
This  function  is  available  when  the  projector  is  turned  off 
and  in  Stand-by.    It  is  recommended  to  use  Eco  under 
normal condition.
  Normal . . . . . . . . . .  n
 o r m a l   p o w e r   c o n s u m p t i o n   i n 
Stand-by condition.  
  Eco
. . . . . . . . . . . . .  l
 o w e r  p o w e r  c o n s u m p t i o n  t h a n 
Normal mode in Stand-by condition.