Home > Sanyo > Projector > Sanyo Projector Plc Xu300 User Manual

Sanyo Projector Plc Xu300 User Manual

Here you can view all the pages of manual Sanyo Projector Plc Xu300 User Manual. The Sanyo manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 61

61

Cleaning the Projector Cabinet
Cleaning the Projection Lens
Unplug	the	AC	power	cord	before	cleaning.
Gently	 wipe	the	projection	 lens	with	a	cleaning	 cloth	that	
c o n t a i n s 	a 	s m a l l 	a m o u n t 	o f 	n o n - a b r a s i v e 	c a m e r a 	l e n s	
c l e a n e r, 	o r 	u s e 	a 	l e n s 	c l e a n i n g 	p a p e r 	o r 	c o m m e r c i a l l y	
available	air	blower	to	clean	the	lens.	
Avoid 	using 	an 	excessive 	amount 	of 	cleaner. 	Abrasive	
cleaners,	 solvents,	or	other	 harsh...

Page 62

6

When	the	projection	 lamp	of	the	 projector	 reaches	its	end	
of	 life,	 the	Lamp	 replacement	 icon	appears	 on	the	 screen	
and	 LAMP 	REPLACE	 indicator	lights	yellow.	 Replace	 the	
lamp	 with	a	new	 one	promptly.	 The	timing	 when	the	LAMP 	
REPLACE	 indicator	should	light	is	depending	 on	the	 lamp	
mode.
Follow	these	steps	to	replace	the	lamp.
For	 continued	 safety,	replace	 with	a	lamp	 of	the	
same	 type.	Do	not	 drop	 a	lamp	 or	touch	 a	glass	
bulb!	 The	glass	can	shatter	and	may...

Page 63

63

This	projector	uses	a	high-pressure	lamp	which	must	be	handled	carefully	and	properly.		
Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
●	Lamp	 life	may	 differ	 from	lamp	 to	lamp	 and	according	 to	the	 environment	 of	use.	 There	 is	no	 guarantee	
of	 the	 same	 life	for	each	 lamp.	 Some	 lamps	 may	fail	or	terminate	 their	life	in	a	shorter	 period	of	time	
than	other	similar	lamps.
●	 If	 the	 projector	 indicates	 that	the	lamp	 should	 be	replaced,	 i.e.,	if	the...

Page 64

64

 Problem:	 –	Solutions
  No power 	 –	Plug	the	power	cord	of	the	projector	into	the	AC	outlet.
	
	 	 –	See	if	the	POWER	indicator	lights	red.
	
	 	 –		
Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	
again.	 The	projector	can	be	turned	on	after	the	POWER	indicator	
turns	red.	See	page	18.
	 	 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights	red,																	
																																																																					projector	cannot	be	turned	on....

Page 65

65

 No image	 –	Check	the	connection	between	your	computer	or	video	equipment		
	 	 	 and	the	projector.	See	pages	14-16.
	
	 	 –	See	if	the	input	signal	is	correctly	output	from	your	computer.	Some		
	 	 	 laptop	computers	may	need	to	change	the	setting	for	monitor	output		
	 	 			when	connecting	to	a	projector.	See	your	computer’s	instruction		
	 	 	 manual	for	the	setting.	
	
	 	 –	It	takes	about	30	seconds	to	display	an	image	after	turning	on	the		
	 	 	 projector.	See	page	18.
	 	 –		
Check	the...

Page 66

66

 The image is distorted or runs off .  –	Check	PC adjustment	menu	or	Screen	and	adjust	them.		 	
	 	 			See	pages	31-32,	35-36.
  PIN code dialog box appears 	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“1234”	or	numbers	
	at start-up . 	 	 you	have	set).	See	pages	19,	54-55.
  The Remote Control does 	–	Check	the	batteries.
	
	not work . 	 –	Make	sure	no	obstruction	is	between	the	projector	and	remote	 	
	 	 			control.
	
	 	 –	Make	sure	you	are	not	too	far	from	the	projector	when	using...

Page 67

67

wARNING :
High voltages are used to operate this projector  . Do not attempt to open the cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	
projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	
how	to	obtain	service.
This	symbol	 on	the	 nameplate	
m e a n s 	t h e 	p r o d u c t 	i s 	L i s t e d	
by	 Underwriters	 Laboratories	
I n c . 	 	I t	i s 	d e s i g n e d 	a n d...

Page 68

68

Menu Tree
SVGA	1Mode	1Mode	2	-	-	-	-
Total	dotsHorizontalVertical
Display	area	HDisplay	area	VReset
Dynamic
RealBlackboard	(Green)
Image	1Image	2Image	3
Image AdjustContrastBrightnessColor	temp.
Red
Gamma
Store
NormalTrue
Digital	zoom	–
Full	
0–630–63
Computer Input
PC Adjust
Mode	1Mode	2Mode	3Mode	4Mode	5
Image Select
0–63
0–15
Image	1Image	2Image	3Image	4
Screen
Yes/No
	*	Systems	displayed	in	the	System	Menu	vary	
depending	on	an	input	signal.
ResetYes/No
Sharpness0–15
Computer Input/Video Input...

Page 69

69

AutoPALSECAMNTSCNTSC	4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard	(Green)
Image	1Image	2Image	3
Normal
0–630–63
Off
Setting
Image Select
System (2)
System (3)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15	0–15
Image	1
Screen
Yes/No
Image	4
LanguageSetting17	languages	provided.
Blue/Black/UserOn/Countdown	off/Off	Logo	select
On/Off
On/Off
Ready
On/Off
Code	1–Code	2
KeystoneBackgroundDisplayLogo...

Page 70

70

Check	the	indicators	for	projector	condition.																																			
•	•	•	green.•	•	•	red•	•	•	off
•	•	•	blinks	green.
When	the	projection	lamp	reaches	its	end	of	life,	the	LAMP	REPLACE	indicator	lights	yellow.	When	this	indicator	
lights	yellow,	replace	the	projection	lamp	with	a	new	one	promptly.
The	projector	is	off.	(The	 AC	power	cord	is	unplugged.)
The	projector	is	in	stand-by	mode.	Press	the	ON/STAND-BY 	button	
to	turn	on	the	projector.
Projector ConditionPOWERred/green...
Start reading Sanyo Projector Plc Xu300 User Manual

Related Manuals for Sanyo Projector Plc Xu300 User Manual

All Sanyo manuals