Sanyo Projector Plc Xu10n User Manual

21
BEFORE OPERATION
VIEW MENU
Used to display, read
or write the image data
in a memory card
through the PC CARD
SLOT.
(Refer to P34, 37)
MODE MENU
Used to select
the MCI input
mode.
(Refer to P34)
MENU BAR IN MCI MODEPress MENU BUTTON while being in MCI mode.
These icons have the
same function as the
Computer Mode.
POSITION MENU
Used to adjust
the position of
the image.
(Refer to P36)
SCREEN MENU
Used to adjust
the size of the
image.
(Refer to P36)
IMAGE MENU
Used to adjust  the
computer image. [Fine...

22
BASIC OPERATIONS
Turning on the Projector
Connect the projectors AC power cord into a wall outlet.  The
LAMP POWER indicator lights RED, and the READY indicator
lights GREEN.
Press the power ON-OFF button on the Remote Control Unit or on
the Top Control to ON.  The LAMP POWER indicator dims, and
the Cooling Fans start to operate.  The Preparation Display
appears on the screen and the count-down starts.  The signal
from the source appears after 30 seconds.
2
3
Turning off the Projector
Press the power...

23
BASIC OPERATION
ADJUSTING THE IMAGE
ZOOM Adjustment
1Press ZOOM button on the Top Control or the Remote Control to
turn into the ZOOM mode.
2Adjust the size of the image by pressing POINT UP/DOWN
button.
Press UP button to have the image larger, and press DOWN
button to have the smaller.ZOOM
The message disappears after 4 seconds.
FOCUS Adjustment
1Press FOCUS button on the Top Control or the Remote Control to
turn into the FOCUS mode.
2Adjust the focus of the image by pressing POINT UP or DOWN...

Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SOUND
and press the SELECT button.  Another dialog box SOUND
ADJUST Menu will appear. 
24
BASIC OPERATION
Sound Volume Adjustment
Press the VOLUME (+/–) buttons (located on the Top Control or on the
Remote Control Units) to adjust the volume.  The Volume dialog box
appears on the screen for a few seconds.
(+) button to increase the volume, and (–) button  decreasing.
Sound Mute Setting
Press the MUTE...

Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Computer  and
press the SELECT button.  
25
COMPUTER MODE
SELECTING COMPUTER MODE
Direct Operation
Press the MODE button on the Top Control or the COMPUTER / MCI
button on Remote Control Unit.  Select the Mode among COMPUTER,
VIDEO, or MCI mode.
Menu Operation
When selecting the Computer Mode, the Current Mode display appears.
It shows the information of the computer of the mode selected.  
CURRENT MODE...

26
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically detect display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be detected by this projector.  If this happens, the projector cannot reproduce a proper image and the image
is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
The number of the total vertical lines....

27
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and
less than 160 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x...

28
COMPUTER MODE
PICTURE IMAGE ADJUSTMENT
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select IMAGE  and
press the SELECT button.  Another dialog box PICTURE IMAGE
ADJUSTMENT Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to 
sor tof the item that you want to change by
pressing the POINT UP/DOWN buttons.  To increase the value,
point the arrow to 
sand then press the SELECT button.  To
decrease the value...

29
COMPUTER MODE
The Auto Image function is provided to automatically adjust Fine sync.,
Total dots, and Picture Position for most computers.
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE
and press the SELECT button.  
Another dialog box AUTO IMAGE Menu will appear. 
Move the arrow to an item that you want to adjust by pressing the
POINT UP/DOWN button.  Change the setting On or Off by
pressing the SELECT button.  
1
2
Auto Image...

30
COMPUTER MODE
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select POSITION 
and press the SELECT button.  Another dialog box PICTURE
POSITION Menu will appear. 
Select the arrow to the direction (described as  ,  ,  or  )
that you want to adjust by pressing the POINT UP/DOWN buttons,
and then press the SELECT button....