Sanyo Projector Plc Xu10n User Manual

11
CONNECTING THE PROJECTOR
¥
COMPUTER INMONITOR OUT
CONTROL PORT
AUDIO INMCI SERIAL
AUDIO OUT
(MONO)VIDEO R-AUDIO-LS-VIDEO
CONNECTING TO THE VIDEO EQUIPMENTS
Satellite 
TV TurnerVideo Cassette Recorder Video Disc Player
Video Audio Cable
(Not supplied)S-VIDEO Cable
(Not supplied)
Audio Amplifier Audio Speaker
(stereo) External Audio Equipment
Audio Cable
(Stereo / Not supplied)
Terminals 
of the Projector
Use the either of VIDEO jack
or S-VIDEO jack.  When the
both jacks are connected, the
S-VIDEO jack...

12
CONNECTING THE PROJECTOR
CONNECTING TO THE IBM-COMPATIBLE COMPUTER
To connect with the IBM-compatible  computer, refer to the figure below.
· VGA CABLE (supplied)
· MOUSE CABLE FOR PS/2 PORT or SERIAL PORT (supplied)
· MCI SERIAL CABLE (supplied)
· MONITOR CABLE (not supplied)
· AUDIO CABLE (stereo /not supplied)
uBe sure to connect the MOUSE CABLE corresponding with the terminal of your computer.
Use Cables and Adapter indicated below.
IBM-COMPATIBLE COMPUTERS (VGA / SVGA / XGA / SXGA)
VGA Cable...

13
B
A
 
¥
COMPUTER INMONITOR OUT
CONTROL PORT
AUDIO INMCI SERIAL
AUDIO OUT
(MONO)VIDEO R-AUDIO-LS-VIDEO
CONNECTING THE PROJECTOR
To disconnect MOUSE CABLE,
1. Hold the portion (B) of the
connector with one hand.
2. Pull the portion (A) to the
arrow direction and remove
connector.
CONTROL PORTAUDIO OUT AUDIO INMONITOR OUT
COMPUTER IN MCI SERIAL
Use either of these Mouse Cables corresponding
with your terminal of your computer. 

14
CONNECTING THE PROJECTOR
ON
12
34
56DIP
CONNECTION TO THE MACINTOSH COMPUTER
To connect with the Macintosh computer, refer to the figure below.
· VGA CABLE (supplied)
· VGA/MAC ADAPTER (supplied)
· MOUSE CABLE FOR ADB PORT (supplied)
· MONITOR CABLE (not supplied)
· PC AUDIO CABLE (stereo / not supplied)
Use Cables and Adapter indicated below.
MACINTOSH COMPUTERS (VGA / SVGA / XGA / SXGA)
VGA Cable (supplied)
Monitor Output  Desktop type Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
Mouse...

ON
1
2
34
56
DIP
B
A
ON
OFF
¥
COMPUTER INMONITOR OUT
CONTROL PORT
AUDIO INMCI SERIAL
AUDIO OUT
VIDEO R-AUDIO-LS-VIDEO
(MONO)
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF ON ON
ON ON
ON ONOFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF1234 56
OFF OFF ON ON ON ON 21 MODE (1152 x 870)
15
CONNECTING THE PROJECTOR
CONTROL PORT AUDIO OUTAUDIO INMONITOR OUT
COMPUTER IN
To disconnect MOUSE CABLE,
1. Hold the portion (B) of the
connector with one hand.
2. Pull the portion (A) to the
arrow direction...

PA G E
MENUAUTO IMAGE
MUTE
VOLUME
FOCUS
ZOOM
ON-OFF
NORMAL
CURSOR
COMPUTER/
MCIVIDEO
F
R
E
E
Z
E
/
N
O
 S
H
O
W
D. Z OOMLASER
16
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
COMPUTER / MCI BUTTON
Used to select source either
COMPUTER or MCI mode.
(P25)
This remote control unit is not only able to operate the projector but also usable as a wireless mouse for a PC.
POINT button and two CLICK buttons are used for wireless mouse operation. (Refer to page 41.)
Wireless mouse is usable when PC mouse...

17
BEFORE OPERATION
Remote Control Batteries Installation
123
Slide the lid
upward.
Press the lid
downward and
slide it.
For correct polarity (+ and –), be sure
the battery terminals are in contact
with the pins in the compartment.
Remove the battery
compartment lid.Slide the batteries into
the compartment.Replace the compartment
lid.
Operating Range of the Remote Control
To insure safe operation, please observe the following precautions :
lUse (2) AA type alkaline batteries.
lReplace two batteries at...

18
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
LAMP REPLACE
LAMPWARNING TEMP.
READY
SELECT MENU
MODE AUTO IMAGE
PAGE ZOOMFOCUS
VOLUME NORMALON–OFF
+
–
Used to select zoom adjust.
(Refer to P23.)
Used to active or terminate the
MENU operation.
(Refer to P19.)
MENU BUTTON
MODE BUTTON
AUTO IMAGE BUTTON
PAGE BUTTONS
READY INDICATOR
SELECT BUTTON
POWER ON–OFF BUTTON
FOCUS BUTTON
NORMAL BUTTON
VOLUME BUTTONS
WARNING TEMP. INDICATOR
LAMP INDICATOR
POINT BUTTONS
LAMP REPLACE INDICATOR
Used to select input...

19
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU
Display ON-SCREEN MENU
Press MENU button to display the ON-SCREEN MENU (MENU
BAR).  The red frame is the POINTER.
Select the ITEM by pressing SELECT button.  The dialog box of
the ITEM appears.
Move the POINTER (red frame) to the ITEM ICON that you want
to select by pressing POINT RIGHT/ LEFT buttons.
Move the POINTER to the ITEM that you want to adjust and
adjust the ITEM by pressing SELECT button.
Refer to the following pages for...

20
BEFORE OPERATION
MENU BAR
SYSTEM MENU
Used to select a
computer
system.
(Refer to P25)
IMAGE MENU
Used to adjust  the
computer image. [Fine
sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P28)
PC ADJUST MENU
Used to adjust the
parameters to
match with the input
signal format.
(Refer to P26)
SETTING MENU
Used to set the Display
Menu and to reset
Lamp Replacement
Monitor Timer.
(Refer to P40)
LANGUAGE MENU
Used to select
the language
used in the Menu.
(Refer to P40)
MODE MENU
Used...