Sanyo Projector Plc Xu07N User Manual

31
VIDEO MODE
PICTURE IMAGE ADJUSTMENT
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select IMAGE  and
press the SELECT button.  Another dialog box PICTURE IMAGE
ADJUSTMENT Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to sor tof the item that you want to change by
pressing the POINT UP/DOWN buttons.  To increase the value,
point the arrow to sand then press the SELECT button.  To
decrease the value point...

32
SETTING
SETTING MENU
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SETTING
and press the SELECT button.  Another dialog box
SETTING Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to the item that you want to set, and then press
the 
SELECT button to set it On or Off.  
1
2
Blue backWhen this function is in the On position, this projector
will produce a blue image without video noise on the
screen...

33
APPENDIX
OPERATING WIRELESS MOUSE
Installation
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse
for a PC.  POINT buttons and two CLICK buttons are used for wireless mouse operation.
Wireless mouse is usable when PC mouse pointer is displayed on the screen.  When the menu or indicator of
the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used.
Connect the mouse port of your computer to the...

34
CLEANING THE PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
When you dont use the projector, replace the lens cover.
1
3
Lightly wipe the cleaning cloth over the lens.2
Follow these steps to clean the projection lens:
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal...

35
APPENDIX
LAMP REPLACEMENT Indicator
When the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow.  When the
image become dark or the color of the image become unnatural, replacement of the Lamp is required.
Turn off the projector and disconnect the AC plug.  Allow the
projector to cool for at least 45 minutes.
Remove 2 screws with a screwdriver and pull out the lamp
assembly by grasping the handle.
1
3
Lamp Replacement Monitor Timer
Replace the Lamp Assembly and...

36
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service station for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment a s described in section CONNECTING
THE PROJECTOR  on pages 10 ~ 15.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce the image, re-start the computer.
5. If the image sill does not...

37
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
Sanyo Service is easily obtained.  If after following all operating instructions, you find that service is
necessary, contact the SFS Corporation in Los Angeles, or the store where you purchased the unit.  Give the
model number and explain the difficulty.  We will advise you how to obtain service.
Remote Control
Unit does not work.lCheck the batteries.
lMake sure anything is blocking between the...

38
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc.  It
is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty
and electrical hazards.
0.9 TFT Active Matrix type, 3 panels
TECHNICAL SPECIFICATIONS
Multi-media Projector
9.48 lbs (4.3 kg)
8.46 x 4.29 x 12.85 (215mm x 109mm x 326.5mm) 
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43 and PAL-M
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable...

39
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give the
name and the Type No. of it to the sales dealer.
lControl Cable for Serial Port Type No. : POA-MC12SRL
lControl Cable for ADB Port Type No. : POA-MC12MAC
lMAC Adapter Type No. : POA-MACAP 

1YEAR
In order to obtain warranty service, the product must be delivered to and picked up from and Authorized Sanyo Factory
Service Center at the users expense, unless specifically stated otherwise in this warranty.  the names and addresses of
authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO  FISHER COMPANY (SFC) warrants this
SANYO product against defects in materials and workmanship for the...