Sanyo Projector Plc Xu07N User Manual

21
BASIC OPERATIONS
Turning on the Projector
Connect the projectors AC power cord into a wall outlet.  The
LAMP POWER indicator lights RED, and the READY indicator
lights GREEN.
Press the power ON-OFF button on the Remote Control Unit or on
the Top Control to ON.  The LAMP POWER indicator dims, and
the Cooling Fans start to operate.  The Preparation Display
appears on the screen and the count-down starts.  The signal
from the source appears after 30 seconds.
2
3
Turning off the Projector
Press the power...

22
BASIC OPERATION
ADJUSTING THE PICTURE
ZOOM Adjustment
1Press ZOOM  / button on the Remote Control Unit or ZOOM
s/tbutton on the Top Control to turn into the ZOOM mode.
2Press ZOOM  or sbutton to have the image larger, and press
ZOOM or tbutton to have the smaller.Zoom
The message disappears after 4 seconds.
FOCUS Adjustment
1Press FOCUS  / button on the Remote Control Unit or
FOCUS s/ton the Top Control to turn into the FOCUS mode.
2Adjust the focus of the image by pressing FOCUS  / or
FOCUS...

23
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SOUND
and press the SELECT button.  Another dialog box SOUND
ADJUST Menu will appear. 
BASIC OPERATION
Sound Volume Adjustment
Press the VOLUME (+/–) buttons (located on the Top Control or on the
Remote Control Unit) to adjust the volume.  The Volume dialog box
appears on the screen for a few seconds.
(+) button to increase the volume, and (–) button decreasing.
Sound Mute Setting
Press the MUTE...

24
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Computer  and
press the SELECT button.  
COMPUTER MODE
SELECTING COMPUTER MODE
Direct Operation
Press the MODE button on the Top Control or the Remote Control Unit.
The  input source is selected among COMPUTER or VIDEO.  The
“Computer” or “Video” display will appear on the screen for a few
seconds.
Menu Operation
When selecting the Computer Mode, the Current Mode display appears.
It shows the...

25
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically detect display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be detected by this projector.  If this happens, the projector cannot reproduce a proper image and the image
is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
The number of the total vertical lines....

26
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and
less than 165 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x...

27
COMPUTER MODE
PICTURE IMAGE ADJUSTMENT
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select IMAGE  and
press the SELECT button.  Another dialog box PICTURE IMAGE
ADJUSTMENT Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to 
sor tof the item that you want to change by
pressing the POINT UP/DOWN buttons.  To increase the value,
point the arrow to 
sand then press the SELECT button.  To
decrease the value...

28
COMPUTER MODE
The Auto Image function is provided to automatically adjust Fine sync.,
Total dots, and Picture Position for most computers.
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE
and press the SELECT button.  
Another dialog box AUTO IMAGE Menu will appear. 
Move the arrow to an item that you want to adjust by pressing the
POINT UP/DOWN button.  Change the setting On or Off by
pressing the SELECT button.  
1
2
Auto Image...

29
COMPUTER MODE
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select POSITION 
and press the SELECT button.  Another dialog box PICTURE
POSITION Menu will appear. 
Select the arrow to the direction (described as  ,  ,  or  )
that you want to adjust by pressing the POINT UP/DOWN buttons,
and then press the SELECT button....

30
VIDEO MODE
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Video  and press
the SELECT button.  
SELECTING VIDEO MODE
Direct Operation
Press the MODE button on the Top Control or the Remote Control Unit.
The  input source is selected among VIDEO or COMPUTER.  The
“Video” or “Computer” display will appear on the screen for a few
seconds.
Menu Operation
SELECTING COLOR SYSTEM
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT...