Sanyo Projector Plc Xt35l User Manual

61
The	WARNING	indicators	show	the	state	of	the	function	which	protects	the	projector.	Check	the	state	of	the	
WARNING	indicators	and	the	POWER	indicator	to	take	proper	maintenance.	
Warning	Indicators
The	projector	is	shut	down	and	the	WARNING	TEMP.	
indicator	is	blinking	red.
When	the	temperature	inside	the	projector	reaches	a	
certain	level,	the	projector	will	be	automatically	shut	
down	to	protect	the	inside	of	the	projector.	 The	POWER	
indicator	is	blinking	while	the	projector	is	being	cooled...

6
Unplug	the	AC	power	cord	before	cleaning.
Gently	wipe	the	projection	lens	with	a	cleaning	cloth	that	
contains	a	small	amount	of	non-abrasive	camera	lens	cleaner,	
or	use	a	lens	cleaning	paper	or	commercially	available	air	
blower	to	clean	the	lens.	
Avoid	using	an	excessive	amount	of	cleaner.	 Abrasive	
cleaners,	solvents,	or	other	harsh	chemicals	might	scratch	
the	surface	of	the	lens.
When	the	projector	is	not	in	use,	replace	the	lens	cap.
Cleaning	the	Projector	Cabinet
Unplug	the	 AC	power...

63
Troubleshooting
Before	calling	your	dealer	or	service	center	for	assistance,	check	the	items	below	once	again.
–	Make	sure	you	have	properly	connected	the	projector	to	peripheral	equipment	as	described	on	pages	20–22.	
–	Make	sure	all	equipment	is	connected	to	AC	outlet	and	the	power	is	turned	on.
–	When	the	projector	does	not	project	an	image	from	the	connected	computer,	restart	the	computer.		
  Problem:	 –	 Solutions
  No power 	 –	 Plug	the	power	cord	of	the	projector	into	the	 AC	outlet.
	
	 	 –...

64
	 		 off	and	wait	until	condensation	evaporates.	
	 	 –	 Projecting	from	the	excessive	slant	angle	to	the	screen	may	cause		 	
	 	 	 keystone	distortion	and	partial	imperfect	focus.	See	page	18.
  Picture is not bright enough .  –	 Check	if	"Contrast"	or	"Brightness"	are	adjusted	properly	See	page	42.
	
	 	 –	 Check	if	"Image	level"	is	selected	properly	See	page	41.
	
	 	 –	 Check	the	LAMP	REPLACE	indicator.	If	it	lights,	the	end	of	lamp	life	is
	
	 	 	 approaching.	Replace...

65

Appendix
This	symbol	on	the	nameplate	means	the	product	
is	Listed	by	Under writers	Laboratories	Inc.	It	is	
designed	and	manufactured	to	meet	rigid	U.L.	
safety	standards	against	risk	of	fire,	casualty	and	
electrical	hazards.The	CE	Mark	is	a	Directive	
conformity	mark	of	the	European	
Community	(EC).
WARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you...

66

Menu	Tree
Dynamic
RealCinema*Image	1Image	2Image	3
Image
VolumeMuteQuitOn/OffSound0–63
Input
Input	3Auto
Go	to	System	(3)
Go	to	System	(3)
Video	
Go	to	System	(1)
S-video
Standard
Quit
Input	1
Go	to	System	(3)Video
Go	to	System	(1)Input	2	RGB
Go	to	System	(2)Component
Image	4
RGB	(PC	Analog)
RGB	(Scart)
RGB	(PC	Digital)
RGB	(AV	HDCP)
Quit
Quit
SySTEM (3)SySTEM (1)
-	-	-	-
Mode	1
Mode	2
XGA	1SECAM
NTSC
Auto
PAL
PAL-M
PAL-N
NTSC4.43
SySTEM (2)
1035i
720p
Auto
1080i
480p
575i
575p
480i
InputH-sync...

67

LanguageSetting12	languages	provided
Blue/User/BlackAuto	1
Normal
BackgroundLamp	control
Quit
Capture
Logo 	PIN 	code 	change
Logo	PIN	code	lock
Quit
Auto	2High
QuitAuto	PC	adj.
Total	dotsHorizontalVertical
Display	area	HDisplay	area	 VReset
PC Adjust
Yes/No
Clamp
Current	mode
Mode	free/Store
Quit
Fine	sync0–31
Mode	1
H-sync	freq.V-sync	freq.Quit
NormalTrueWideFull	screen
Screen
Logo	selectLogoOff/Default/User
Yes/No
On/Off
Eco	1Eco	2
✔Note:
	 •	The	Menu	display	varies	depending	on	the	input...

68

Indicators
Projector ConditionPOWERgreenLAMPred
WARNINGTEMP.red
The	projector	is	off.	(The	AC	power	cord	is	unplugged.)
The	projector	is	in	stand-by	mode.	Press	the	ON/STAND-BY	button	to	
turn	on	the	projector.
The	projector	is	operating	normally.
The	projector	is	in	the	Power	management	mode.
The	projector	is	preparing	for	stand-by	or	the	projection	lamp	is	
being	cooled	down.	 The	projector	cannot	be	turned	on	until	cooling	is	
completed	and	the	POWER	indicator	stops	blinking.
The	temperature...

69

––
––
WARNINGFILTERorange
*	When	the	projection	lamp	reaches	its	end	of	life,	the	LAMP	REPLACE	indicator	lights	yellow.	When	this	indicator	lights	
yellow,	replace	the	projection	lamp	with	a	new	one	promptly.	Reset	the	lamp	counter	after	replacing	the	lamp.	See	pages	
59–60.
The	filter	is	clogged.	Stop	using	the	projector	immediately	and	clean	
or	replace	the	filter	(see	below).
Projector ConditionPOWERgreen
Indicators
WARNING FILTER indicator
The	Filter	counter	reached	a	set	time.	Clean	or	replace...

70

Compatible	Computer	Specifications
Basically	this	projector	can	accept	the	signal	from	all	computers	with	the	V-	and	H-Frequency	mentioned	
below	and	less	than	140	MHz	of	Dot	Clock. 	PC	Adjustment	is	limited	when	selecting	these	modes.
Appendix
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
VGA	1
640x480 31.470	59.880	
VGA	2
720x400 31.470	70.090	
VGA	3
640x400 31.470	70.090	
VGA	4
640x480 37.860	74.380	
VGA	5
640x480 37.860	72.810	
VGA	6
640x480 37.500	75.000	
VGA	7
640x480 43.269	85.000...