Sanyo Projector Plc Xt35l User Manual

1
Connecting	to	Video	Equipment	(Video,	S-Video)
Cables used for connection  
•	Video	Cables	(RCA	x	1)	 •	Audio	Cables	(Mini	Plug	[stereo]	x	2)
•	S-VIDEO	Cable	 •	BNC	Cable
•	 Audio	Cable	(RCA	x	2)	
(Cables	are	not	supplied	with	the	projector.)
External	 Audio	Equipment
Audio	cable	
(stereo)
VIDEOS-VIDEO
S-video	
cable
Video	and	
audio	cable
Composite	
Video	and	Audio	Output S-video	
Output
AUDIO	IN Audio	Input
AUDIO	OUT	
(stereo)
(R)(L)(Video)
Unplug the power cords of both the projector and...


Connecting	to	Video	Equipment	(Component	and	RGB	Scart)
Cables used for connection	
•	Audio	Cables	(Mini	Plug	[stereo]	x	2)
•	Scart-VGA	Cable
•	BNC	Cable
•	DVI-Digital	Cable
(Cables	are	not	supplied	with	the	projector.)
External	 Audio	Equipment
Audio	cable	
(stereo)
Audio	Input
Component	
Video	
Output
(Y,	Cb/Pb,	Cr/Pr)
RGB	Scart		
21-pin	Input Audio	
Output
Scart-VGA	
cable
AUDIO	OUT	
(stereo)
Audio	
cable	
(stereo)AUDIO	
IN
ANALOG	OUTY			Cb/Pb			Cr/PrANALOG	
IN
Scart-VGA	
cable
BNC	cable...

3
NOTE ON THE POWER CORD
	 	 AC	power	cord	must	meet	the	requirements	of	the	country	where	you	use	the	projector.
	 	 Confirm	the	AC	plug	type	with	the	chart	below	and	proper	 AC	power	cord	must	be	used.
	 	 If	supplied	the	 AC	power	cord	does	not	match	your	 AC	outlet,	contact	your	sales	dealer.
To	power	cord	
connector	on	your	
projector.
Projector sideAC outlet side
Ground
To the AC outlet .
(120	V	AC)
For Continental EuropeFor the U  .S .A .  and Canada
This	projector	uses	nominal	input...

4
4
Connect	the	projector’s	AC	power	cord	into	an	AC	
outlet.	 The	POWER	indicator	lights	green.
Press	the	ON/STAND-BY	button	on	the	top	control	
or	the	ON	button	on	the	remote	control.	 The	LAMP	
indicator	lights	red	and	the	cooling	fans	start	to	operate.	
The	preparation	display	appears	on	the	screen	and	the	
count	down	starts.	
2
3
1
16
The	preparation	display	will	disappear	
after	30	seconds.
4After	the	countdown,	the	input	source	that	was	
selected	the	last	time	and	the	lamp	control...

5
5
Press	the	ON/STAND-BY	button	on	the	top	control	
or	the	STAND-BY	button	on	the	remote	control,	and	
“Power	off?”	appears	on	the	screen.
Press	the	ON/STAND-BY	button	or	the	STAND-BY	button	
on	the	remote	control	again	to	turn	off	the	projector.	
The	LAMP	indicator	turns	off	and	the	POWER	indicator	
starts	to	blink	green.	After	the	projector	is	turned	off,	
the	cooling	fans	operates	for	90	seconds.	During	the	
POWER	indicator	is	blinking,	you	cannot	turn	on	the	
projector.
1
2
TO	MAINTAIN...

6

Top Control
Menu barPointer(red frame )
Menu icon
Item data
Press	the	Point	
7 8	
buttons	to	adjust	the	
value.
SELECT button
Pointer (red frame )
Press	the	Point	
ed	buttons	
to	move	the	pointer.
Item
How	to	Operate	the	On-Screen	Menu
MENU button
SELECT button
POINT buttons
On-Screen Menu
Quit
Exit	this	menu.
The	projector	can	be	adjusted	or	set	via	the	On-Screen	
Menu.	For	each	adjustment	and	setting	procedure,	refer	to	
the	respective	sections	in	this	manual.
Use	the	Point	
7 8	buttons	to...

7

Menu	Bar
System
Select	a	
computer	or	
video	system	
mode	(pp.36,	
37).
Image Adjust
Adjust	the	picture	
image	(pp.42–44).
–	Contrast
–	Brightness
–	
–	
–	Color	temp.
–	White	balance
			(R/G/B)
–	Sharpness
–	Gamma
–	
–	
–	Reset
–	Store
–	Quit
Setting Menu
Set	the	projector’s	
operating	
configurations	(pp.49–
57).
–	Language
–	Logo
–	Background
–	Lamp	control
–	Pointer
–	Remote	Control
–	RC	sensor
–	Display
–	Power	management
–	On	start
–	Fan	control
–	Security
–	 Test	pattern
–	 Warning	log
–...

8

The	following	lens	operation	can	be	made	with	the	Lens	
button	on	the	top	control.	
Press	the	Lens	button	to	enter	each	lens	operation	mode.	
The	selected	adjustment	display	appears	on	the	screen.
Operating	with	Projector	Control
Display	“Lens	shift”	on	the	screen.	Use	the	Point	ed7 8	
buttons	 to	position	 the	screen	 to	the	 desired	 point	without	
having	picture	distortion.	
The	screen	can	be	moved	up	or	down	to	50	percent,	or	
sideways	up	to	15	percent	from	the	central	axis	of	the	
lens...

9

1
2
Press	the	MENU	button	to	display	the	On-Screen	
Menu.	Use	the	Point	
7 8	buttons	to	move	the	red	
frame	pointer	to	the	Sound	Menu	icon.
Press	the	 VOLUME+/–	buttons	on	the	top	control	or	on	the	
remote	control	to	adjust	the	volume.	 The	volume	dialog	box	
appears	on	the	screen	for	a	few	seconds.
Press	the	MUTE	button	on	the	remote	control	to	temporarily	
turn	off	the	sound.	 To	turn	the	sound	back	on,	press	the	
MUTE	button	again	or	press	the	 VOLUME	+/–	buttons.	The	
Mute	function	is	also...

30

Remote Control
Operating	with	Remote	Control
Using	the	remote	control	for	some	frequently	used	operations	is	advisable.	Just	pressing	one	of	the	buttons	
enables	you	to	make	the	desired	operation	quickly	without	calling	up	the	On-Screen	Menu.
Press	the	FREEZE	button	on	the	remote	control	to	freeze	
the	picture	on	the	screen.	To	cancel	the	Freeze	function,	
press	the	FREEZE	button	again	or	press	any	other	button.
FREEZE button
Press	the	 AUTO	PC	button	on	the	remote	control	to	operate	
the	 Auto	PC...