Sanyo Projector Plc Wxu10n User Manual

EN-20
Adjusting the Projector Zoom and Focus
1. Adjust the image by rotating the zoom ring. Rotate to the right to reduc\
e the image.Rotate to the left to enlarge the image.
2. Focus the image by rotating the focus ring.  A still image is recommended for focusing.
Focus ring Zoom ring 

EN-21
Position the projector in a horizontal position; other positions can cause heat
build-up and damage to the projector.
Make sure the heat ventilation holes are not blocked.Do not use the projector in a smoky environment. Smoke residue may cause\
buildup on critical parts.
32(Min.)
92
152
212
272
302
(Max.)
251.7
226.7
176.7 126.776.7
62
51.7 26.7
1.0m
5m
7m
9m
10m 3m 2m
PROJECTION DISTANCE
(METER)
16 :10  SCREEN
SIZE-DIAGONAL (INCH)
Wide
Tele
1.0
32
26.72.0
62
51.7 3.0
92
76.7 5.0
152
126.7 7.0...

EN-22
Menu Operation
The projector has multilingual On Screen Display menus that allow you to make image
adjustments and change a variety of settings. 

EN-23
How to operate
1. Press MENU button to open the OSD menu.
2. When OSD is displayed, use  S / T  buttons to select any feature in the main menu.
After selecting the desired main menu feature, press  X button to enter sub-menu for
feature setting.
3. Adjust the settings with  W /  X buttons.
4. Press  MENU button, the screen will return to the main menu.
5. To exit OSD, press  MENU button again. The OSD menu will close and the projector
will automatically save the new settings. 

EN-24
Picture (Computer Mode)
Brightness
Adjusts brightness of the image.
QPress W to darken the image.QPress  X to lighten the image.
Contrast
Adjusts contrast of the image.
QPress  W  to decrease the contrast.QPress  X  to increase the contrast.
Fine Sync
“Fine Sync” synchronizes the signal timing of the display with that of the graphic card. If
you experience an unstable or flickering image, use the fine sync functi\
on to correct it.
Total Dots“Total Dots” changes the display data frequency to match...

EN-25
Picture (Video Mode)
Brightness
Adjusts the brightness of the image.
Contrast
Adjusts contrast of the image.
Sharpness
Adjusts the sharpness of the image.
Color
Adjusts the color saturation of the image.
Tint
Adjusts the color balance of red and green.
Color Temperature
Adjusts color temperature. At higher temperature, the screen looks colder; at lower
temperature, the screen looks warmer. If you select “USER”, “Re\
d”, “Green” and “Blue” can
be adjusted.
Red
Manually adjusts red.
Green
Manually...

EN-26
Image (Computer Mode)
Aspect
Use this function to choose your desired image
size.
Q1 TO 1 : Keep the image with original width-
height ratio.
QFILL  ASPECT : Maintain the original aspect
ration of the input signal while enlarging to fill
as much of the output display as possible. 16:
9 input on a 4:3 output will result in back bars
on the top and bottom.
QFILL ALL : The input source will be scaled to
fit the projection screen.
1 TO 1
FILL ASPECT (PC only) If input signal is smaller than LCD...

EN-27
FILL ALL
H Position (Horizontal Position)
QPress W to move the image left.QPress  X to move the image right.
V Position (Vertical Position)
QPress  W to move the image down.QPress  X to move the image up.
Auto PC Adj.
Automatically scans the input source.
1280 x 800
Any type
ofresolution. Always fill the whole LCD. 

EN-28
16:9
Image (Video Mode)
Aspect
Use this function to choose your desired image size.
Q4 : 3 : Change the original aspect 1:1 to 4:3 at the composite video inputor S-video input.
Q1  TO  1 : Keep the image with original width-height ratio at the component input.
QFILL ALL : The input source will be scaled to fit the projection screen.
QANAMORPHIC : M aintain the original aspect  ratio in the center of the output image
and place the majority of the distortion towards the horizontal edges
of the...

EN-29
Setting (Computer / Video Mode)
Menu Position
Choose the menu location on the display screen.
Mounting
Q Front-Desktop
The factory default setting.
Q Front-Ceiling
When you select this function, the projector turns the image upside down\
 for ceiling-
mounted projection.
Q Rear-Desktop
When you select this function, the projector reverses the image so you c\
an project behind
a translucent screen.
Q Rear-Ceiling
When you select this function, the projector reverses and turns the imag\
e upside...