Sanyo Projector Plc Wxu10n User Manual

EN-10
 1Front IR remote control sensor
 2Projection lens
 3Focus ring
 4Zoom ring
 5Control panel
123
6987
45
1011
7
8
 6AC power socket
 7Elevator foot
 8Elevator button
 9Ventilation holes
Lens cap strap
Lens cap
10
11
Projector Over view
Front View 

EN-11
12
345
1
3
3
3
2
This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
Bottom View
 1Air filter cover
 2 Lamp cover
 
3 Ceiling mount  (3-M4*6)
Rear View
 1
Ventilation holes
 2Connection ports
 3Kensington lock
 4Rear IR remote control sensor
 5 Speaker 

EN-12
Using the Product
Control Panel
LED
 1Lamp LED indicator
Refer to “LED Indicator Messages”.
 2 Power LED indicator
Refer to “LED Indicator Messages”.
Button Function
  3 ON / STAND-BY
Refer to “Powering On/Off the Projector”.
  4 Four directional (INPUT/AUTO PC ) buttons
- Use four directional buttons to select items or make adjustments to your\
 selection.
- Manually selects an input source. (Left button)
- Automatically adjusts Fine Sync and Total Dots. This function is available for
computer...

EN-13
Connection Por ts
 1AUDIO IN (R/L)
Connects an audio output from video equipment or computer to this jack.
 2 VIDEO IN
Connects composite video output from video equipment to this jack.
 3 COMPUTER IN
Connects analog RGB output signal from a computer to this jack.
 4 S-VIDEO IN
Connects S-Video output from video equipment to this jack.
 5 DVI-D IN
Connects DVI output from a computer to this jack.
 6 RS-232C
When operating the projector via a computer, connect this to the control\
ling computer’s...

EN-14
Remote Control
 1ON / STAND-BY
Refer to “Powering On/Off the Projector”.
 2 Four directional (INPUT/AUTO PC)
buttons
- Use four directional buttons to select items
or make adjustments to your selection.
- Manually selects an input source. (Left button)
- Automatically adjusts Fine Sync and Total Dots. This function is available
for computer mode only. (Right button)
 3 MENU
Displays or exits the on-screen display menus.
 4 LIGHT
Press and hold this button to activate the
LED light. If you press...

EN-15
Installing the Batteries
1. Open the battery cover in the directionshown.
2. Install batteries as indicated by the diagram inside the compartment.
3. Close the battery cover into position.
Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the battery.
Remove batteries from remote control when not using for extended periods\
.Do not dispose of the used battery along with household waste. Dispose o\
f used
batteries according to local...

EN-16
Remote Control Operation
Point the remote control at the infrared remote sensor and press a butto\
n.  Operating the projector from the front
  Operating the projector from the rear
Do not point the LED light pointer directly to the peoples eyes (espec\
ially small
children). There is a danger of injuiry to the eyes.
The remote control may not operate when there is sunlight or other stron\
g light
such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position...

EN-17
Desktop type
Laptop type
3
658
4122
7
When connecting cable, power cords of both 
a projector and external equipment
should be disconnected from AC outlet.
The figure above is a sample connection. This does not mean that all of these
devices can or must be connected simultaneously.
The cables that come with the projector may differ from the above illustration. The
included cables are based on actual shipment delivery. See page 36 for ordering
optional cables.
Installation
Connecting the Projector...

EN-18
Powering On/Off the Projector
Powering on the projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press ON / STAND-BY  button to turn on the projector.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
JWhen searching message appears on the screen, ensure that the appropriate
signal cable(s) are securely connected.
JThe signal message will appear on the screen when the...

EN-19
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with two elevator feet to adjust the image hei\
ght up to 9.0
degrees.
To raise the image:
1. Press the elevator button.
2. Raise the image to the desired height angle, then release the button to lock theelevator feet into position.
To lower the image:
1. Press the elevator button.
2. Lower the image, then release the button to lock the elevator feet into position.
To avoid damaging the projector, make sure that...