Sanyo Projector Plc Su40 User Manual

41
APPENDIX
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
When the projector is not in use, replace the Lens Cover.
1
3
Lightly wipe a cleaning cloth over the Projection Lens.2
Follow these steps to clean the Projection Lens:
MAINTENANCE
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
AIR FILTER
Pull up and remove.
Turn off the...

42
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the items below once again.
Make sure you have connected the projector to peripheral equipment as described properly in the section CONNECTING
PROJECTOR  on pages 11 ~ 13.
Verify that all computer, video and power cord are properly connected and turn the equipment on.
When you are operating the projector with a computer and it does not produce an image, restart the computer. 
Select the other input source....

43
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center.Give the model number and explain about the problem.  We will advise you how to obtain
service.
Remote Control does
not work.Check the batteries.
Check ALL-OFF switch on the Remote Control is set to “ON.”
Make sure there is no obstructions...

44
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.  
• • • on• • • dim• • • off• • • flashing
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights yellow,
replace the projection lamp with a new one promptly.  Reset the Lamp Replace Counter after replacement of the lamp.  
The projector is OFF.  (The AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON-
OFF...

45
APPENDIX
TECHNICAL SPECIFICATIONS
0.8 TFT Active Matrix type, 3 panels
Multi-media Projector
9.5 lbs (4.3 kg)
13.11 x 3.52 x 9.96 (333mm x 89.5mm x 253mm) (not including Adjustable Feet)
800 x 600 dots
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 36” to 260”
1 speaker, 1.18 x 1.57 (30mm x 40mm) 
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Remote Control and Batteries...

46
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT/MONITOR OUTPUT TERMINAL (ANALOG)
Terminal : HDB15-PIN 
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
DVI-I TERMINAL (DIGITAL/ANALOG) 
1917
21018
31119
41220
51321
61422
71523
81624
C1
C2
C3
C5C4
Pin Configuration
Analog Red Input
Analog...

47
Terminal : Mini DIN 8-PIN
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS / CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
Pin Configuration
2
341
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give the name and Type No. to the sales dealer.
Control Cable (Serial Port) Type No. :...

Printed in Japan
Part No. 610 303 2092 (1AA6P1P3678-- MB3A) 
SANYO Electric Co., Ltd.