Sanyo Projector Plc Su40 User Manual

21
BASIC OPERATION
Press the NO SHOW button on the Remote Control to black out the
image.  To restore to normal, press the NO SHOW button again or
press any other button.
NO SHOW FUNCTION
The message disappears after 4 seconds.
No show
Press the P-TIMER button on the Remote Control.  The timer display
“00 : 00” appears on the screen and the timer starts to count time (00 :
00 ~ 59 : 59).  
To stop the P-TIMER display, press the P-TIMER button.  And then,
press the P-TIMER button again to cancel the...

22
COMPUTER INPUT (RGB Scart 21-Pin Video Input)
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose either Computer 1 or Computer 2 by pressing the INPUT
button on the Top Control or press the COMPUTER button on the
Remote Control.
If the projector cannot reproduce proper image, select correct input
source through MENU OPERATION (see below).
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame pointer to the INPUT Menu icon.1
Move...

23
COMPUTER INPUT
SELECTING COMPUTER SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, or SXGA (refer to the
“COMPATIBLE COMPUTER SPECIFICATIONS” on page 24).  When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting.  (Some computers need setting manually.)
The projector displays one of the Auto, - - -, Mode 1/2/3/4/5, or the system provided in the projector.
When the...

24
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100
MHz of Dot Clock.
NOTE : The projector may not project a proper image for D-SXGA 2 and D-SXGA 3 depending on some computers.  
Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x...

25
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to
your computer.  Auto PC Adjustment function can be operated as follows.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame pointer to the PC ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the AUTO PC Adj. icon and then press the...

26
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals from most personal computers currently distributed.  However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector.  If this happens, the projector cannot reproduce a proper image and the image may be
recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This...

27
COMPUTER INPUT
NOTE : The Full screen cannot be selected after the Display area,
Display area H, and Display area V are adjusted.   
Selects the area displayed by this projector.  Select the resolution at
the Display area dialog box.
Display area
Adjustment of the horizontal area displayed by this projector.  Press
the POINT LEFT/RIGHT button(s) to decrease/increase value and
then press the SELECT button.
Display area H
Adjustment of the vertical area displayed by this projector.  Press the
POINT...

28
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (MENU)
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button to move the red
frame pointer to the IMAGE SELECT Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the level that you want to set and then press the SELECT button.
Move the red frame pointer to the
level and press the SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture level preset on this...

29
COMPUTER INPUT
Press the POINT LEFT/RIGHT
buttons to adjust value.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to move the red
frame pointer to the IMAGE ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the item that you want to adjust, and then press the SELECT
button.  The level of each item is displayed.  Adjust each level by
pressing the POINT LEFT/RIGHT button(s).
Move the red frame pointer to
the item to be...

30
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT button(s) to move the
red frame pointer to the SCREEN Menu icon.
When the Digital zoom + is selected, the ON-SCREEN MENU
disappears and the message “D. Zoom +” is displayed.  Press the
SELECT button to expand the image size.  And press the POINT
UP/DOWN/LEFT/RIGHT...