Sanyo Plc Xp200l Projector User Manual

11
Rear Terminal
t	R/C j ACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (not supplied).
y	USB CONNECTOR (Series B)
  Use this connector when controlling a computer 
with the remote control of the projector. Connect 
the USB terminal of your computer to this 
connector with the supplied USB cable (p.22).
i	AUDIO IN II j ACK
  Connect the audio output (stereo) signal from a 
computer or video equipment (p.24).
r	VIDEO INPUT j ACK...

12
Rear Terminal
Part Names and Functions
!2	AUDIO MONITOR OUTPUT jACK
  This jack outputs the audio signal from computer 
or video equipment to external audio equipment 
(p.24).
✽ Kensington Security Slot
  This slot is for a Kensington lock used to deter theft of the 
projector.
  *Kensington is a registered trademark of ACCO Brands Corporation.
!3	 INFRARED REMOTE RECEIVER (Back)
  The infrared remote receiver is also located in the 
front (pp.10, 16).
✽
!3
!2
!1
!1	MONITOR OUT TERMINAL
  This...

13
q	ON/STAND-By button
  Turn the projector on or off (pp.26–27).
e	MENU button
  Open or close the On-Screen Menu (p.28).
r	Point ed7 8 ( VOLUME + / – ) buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.28).
  – Pan the image in Digital zoom + mode (p.44).
  – Adjust the volume level (with Point 
7 8 buttons) 
(p.31).
!2	WARNING TEMP  . indicator
  Blink red when the internal temperature of the 
projector exceeds the operating range (pp.68, 75-
77 ).
t	SHUTTER button
    
Close...

14
q STAND-B y button
  Turn the projector off (p.27).
r ON button
  Turn the projector on (p.26).
y	INPUT button
  Select a signal (pp.35–37).
i	SCREEN button
 Select the screen size (p.32).
r
Remote Control
!0
!4
q
!4 L- CLICK button
  Act as the left mouse button for wireless mouse 
operation (p.34).
e SIGNAL EMISSION indicator
  Light red while a signal is being sent from the 
remote control to the projector.
o POINT ed 7 8 ( VOLUME + / – , MUTE) buttons
  – Select an item or adjust the value in the...

15
Remote Control
!6
!5
!9
!7
!8
!8	ZOOM ed buttons
  Zoom in and out the images (p.32).
!5	D .ZOOM button
  Select the Digital zoom +/- mode and resize the 
image (p.44).
!9	FOCUS buttons
  Adjust the focus (p.32).
@1	FILTER button
   Scroll the filter (p.33).
@3	FREEZE button
  Freeze the picture on the screen (p.33).
!7	KEy STONE button
  Correct keystone distortion (p.33).
@0 RESET/ON/ALL-OFF switch
  When using the remote control, set this switch to 
“ON.” Set it to “ALL OFF” for power saving when...

16
Remote Control Battery Installation
12 3
Open the battery 
compartment lid.Install new batteries into 
the compartment.Replace the 
compartment lid.
Press the lid downward and 
slide it. Two AAA size batteries
For correct polarity (+ and –), 
be sure battery terminals are 
in contact with pins in the 
compartment.
To ensure safe operation, please observe the following precautions :
 ●
 Use two (2) AAA or LR03 type alkaline batteries.
 ●  Always replace batteries in sets.
 ●  Do not use a new battery...

17
The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 55.
Press and hold the MENU and a number button (1–8) 
for more than five seconds to...

18
ADJUSTABLE FEET
Projection angle can be adjusted up to 6.5 degrees with the 
adjustable feet. 
Rotate the adjustable feet and tilt the projector to the proper 
height; to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate the 
both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button on the 
remote control or select Keystone from the menu (see pages 15, 
33, 44, 48).
Adjustable Feet
Installation 

19
When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the 
sales dealer for detailed information of the optional lens specifications. 
Lens Installation
Shift the lens to the center position by using the 
Lens shift function (p. 30).1
2
Removing the lensTop cover release button
CAUTION
Be careful when handling the lens. Do not 
drop.
3
4
Top cover
Light-block sheet
Installation
While pressing the top cover release button on 
the top cover, slide...

20
NOTES ON LENS INSTALLATION
 ●  Do not touch or remove any parts except the lens and related parts. It may result in    
  malfunctions, electrical shock, fire hazard or other accidents.
 ●  Before installing or replacing the lens, check that the Model No. of the Projection Lens  
  matches to the projector.
 ●  For details of the lens and installation, contact the sales dealer where you purchased the 
   projector.
Fit the lens to the projector. Make sure that the 
lens is fully inserted to the...