Sanyo Plc Xp200l Projector User Manual

							11
Rear Terminal
t	R/C j ACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (not supplied).
y	USB CONNECTOR (Series B)
  Use this connector when controlling a computer 
with the remote control of the projector. Connect 
the USB terminal of your computer to this 
connector with the supplied USB cable (p.22).
i	AUDIO IN II j ACK
  Connect the audio output (stereo) signal from a 
computer or video equipment (p.24).
r	VIDEO INPUT j ACK
  Connect the component or the composite video 
output signal from video equipment to this jack 
(p.23).
u	CONTROL PORT CONNECTOR
  When controlling the projector from a computer, 
connect the computer to this connector with a 
control cable (p.22).
q	COMPUTER INPUT TERMINAL (DIGITAL)
  Connect the computer output digital signal to this 
terminal. The HDTV (HDCP compatible) signal can 
also be connected (pp.22-23).
w	COMPUTER INPUT TERMINAL (ANALOG)
  Connect the computer (or RGB scart) output signal 
to this terminal (pp.22-23).
e	5 BNC INPUT j ACKS
  Connect the component or composite video output 
signal from video equipment to VIDEO/Y, Pb/Cb, 
and Pr/Cr jacks or connect the computer output 
signal (5 BNC Type [Green, Blue, Red, Horiz. Sync, 
and Vert. Sync.]) to G, B, R, H/V, and V jacks (pp.22-
23).
q
w
e
r
t
y
o
u
Part Names and Functions
i
!0
o	S-VIDEO INPUT j ACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.23).
!0	AUDIO IN I j ACK
  Connect the audio output (stereo) signal from a 
computer or video equipment (p.24). 
						

							12
Rear Terminal
Part Names and Functions
!2	AUDIO MONITOR OUTPUT jACK
  This jack outputs the audio signal from computer 
or video equipment to external audio equipment 
(p.24).
✽ Kensington Security Slot
  This slot is for a Kensington lock used to deter theft of the 
projector.
  *Kensington is a registered trademark of ACCO Brands Corporation.
!3	 INFRARED REMOTE RECEIVER (Back)
  The infrared remote receiver is also located in the 
front (pp.10, 16).
✽
!3
!2
!1
!1	MONITOR OUT TERMINAL
  This terminal can be used to output the incoming 
analog RGB signal from INPUT 1-3 terminal to the 
other monitor (pp.22-23). 
						

							13
q	ON/STAND-By button
  Turn the projector on or off (pp.26–27).
e	MENU button
  Open or close the On-Screen Menu (p.28).
r	Point ed7 8 ( VOLUME + / – ) buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.28).
  – Pan the image in Digital zoom + mode (p.44).
  – Adjust the volume level (with Point 
7 8 buttons) 
(p.31).
!2	WARNING TEMP  . indicator
  Blink red when the internal temperature of the 
projector exceeds the operating range (pp.68, 75-
77 ).
t	SHUTTER button
    
Close and open up the built-in shutter. (p.30)
i	POWER indicator
  – Light when in stand-by mode and during 
operations.
  – Blink in the Power management mode (p.56).
Side Control and Indicators
y	SELECT button
  – Execute the selected item (p.28).
  – Expand or compress the image in the Digital 
zoom mode (p.44).
o	LAMP/
SHUTTER  indicator
  Light red during operations.
 Light blue when the shutter is closed (p.75).
!0	LAMP REPLACE indicator
  Light orange when the projection lamp reaches its 
end of life (pp.64, 76).
!1	WARNING FILTER indicator
  – Blink slow when the filter is being scrolled (pp. 
61, 75). 
  – Blink fast when the filter scroll is not working 
properly or the filter cartridge is not installed 
(pp.61, 77).
  – Light orange when the clogging of the filter is 
detected or the filter counter reaches a time set 
in the timer setting, urging immediate filter/ filter 
cartridge replacement (pp.60, 61, 77).
q
w
e
t
y
r
Side ControlIndicators (on the top panel)
u
i
o
!0
!2
Part Names and Functions
!1
w	INPUT button
  Select an input source (pp.35–37).
u	LENS button
  Enter the focus, zoom, and lens shift adjustment 
mode (p.30). 
						

							14
q STAND-B y button
  Turn the projector off (p.27).
r ON button
  Turn the projector on (p.26).
y	INPUT button
  Select a signal (pp.35–37).
i	SCREEN button
 Select the screen size (p.32).
r
Remote Control
!0
!4
q
!4 L- CLICK button
  Act as the left mouse button for wireless mouse 
operation (p.34).
e SIGNAL EMISSION indicator
  Light red while a signal is being sent from the 
remote control to the projector.
o POINT ed 7 8 ( VOLUME + / – , MUTE) buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.28).
  – Pan the image in Digital zoom + mode (p.44).
  – Adjust the volume level (with Point 
7 8 buttons) 
or mute the sound (with Point 
d button.) (p.31).
To ensure safe operation, observe the following 
precautions:
– Do not bend, drop, or expose the remote control to  
   moisture or heat.
–   For cleaning, use a soft dry cloth. Do not apply 
benzene, thinner, splay, or any other chemical 
materials.
e
w  WIRED REMOTE jack
  Connect the remote control cable (not supplied) to 
this jack when using as a wired remote control.
!1 SELECT button
  – Execute the selected item (p.28).
  – Expand or compress the image in the Digital 
zoom mode (p.44).
w
u MENU button
  Open or close the On-Screen Menu (p.28).
!2
!0 MOUSE POINTER button
  Move a pointer of the projector or a pointer for 
wireless mouse operation (p.34).
Part Names and Functions
t	AUTO PC button
  Automatically adjust the computer image to its 
optimum setting (pp.32, 39).
t!3y
u
i
o!1
!3	INFO  . button
  Display the input source information (p.32).
!2	
SHUTTER button
 Close and open up the built-in shutter (p.30).  
						

							15
Remote Control
!6
!5
!9
!7
!8
!8	ZOOM ed buttons
  Zoom in and out the images (p.32).
!5	D .ZOOM button
  Select the Digital zoom +/- mode and resize the 
image (p.44).
!9	FOCUS buttons
  Adjust the focus (p.32).
@1	FILTER button
   Scroll the filter (p.33).
@3	FREEZE button
  Freeze the picture on the screen (p.33).
!7	KEy STONE button
  Correct keystone distortion (p.33).
@0 RESET/ON/ALL-OFF switch
  When using the remote control, set this switch to 
“ON.” Set it to “ALL OFF” for power saving when 
it is not in use. Slide this switch to “RESET” to 
initialize the remote control code.
@5 R-CLICK button
  Act as the right mouse button for wireless mouse 
operation (p.34).
@2 LENS SHIFT button
  Select the Lens Shift function (p.32).
@4 P-TIMER button
  Operate the P-timer function (p.33).
@6
@7 NUMBER buttons
  Act as number buttons. Use these buttons when 
setting the remote control codes (pp.17, 55) or 
when entering the PIN code numbers (pp. 26, 54, 
58).
@2
@1
@0
@3
@4
@6 POINTER button
  Act as the On-Off switch for the Pointer (p.33, 34).
@7
For PIN code 
and remote 
control code.
Part Names and Functions
@5
!6 INPUT 1 – 3 buttons
  Select an input source (INPUT 1 – INPUT 3) 
  (pp.35–37). 
						

							16
Remote Control Battery Installation
12 3
Open the battery 
compartment lid.Install new batteries into 
the compartment.Replace the 
compartment lid.
Press the lid downward and 
slide it. Two AAA size batteries
For correct polarity (+ and –), 
be sure battery terminals are 
in contact with pins in the 
compartment.
To ensure safe operation, please observe the following precautions :
 ●
 Use two (2) AAA or LR03 type alkaline batteries.
 ●  Always replace batteries in sets.
 ●  Do not use a new battery with a used battery.
 ●  Avoid contact with water or liquid.
 ●  Do not expose the remote control to moisture or heat.
 ●  Do not drop the remote control.
 ●  If the battery has leaked on the remote control, carefully wipe 
the case clean and install new batteries.
 ●  Risk of an explosion if battery is replaced by an incorrect type. 
 ●  Dispose of used batteries according to the instructions.
Point the remote control toward the projector (to 
Infrared Remote Receivers) when pressing the buttons. 
Maximum operating range for the remote control is 
about 16.4’ (5 m) and 60 degrees in front and rear of the 
projector.
Infrared Remote Receivers are provided both in front and 
back of the projector. You can conveniently use both of 
the receivers (pp. 10, 56).16.4’
(5 m)Remote Control Receivers and Operating Range
The remote control can be used as a wired remote control. Wired 
remote control helps you use the remote control outside of the 
operating range (16.4’/ 5 m). Connect the remote control and 
the projector with the remote control cable (sold separately). 
Connected with the remote control cable, the remote control does 
not emit wireless signal.
Wired Remote Control Transmitter
Part Names and Functions
16.4’
(5 m)
✔Note:
	 •	 	When	hanging	the	projector	from	the	ceiling,	select	the	Infrared	
Remote	Receiver	which	is	located	farther	away	from	the	
fluorescent	light	(p.56). 
						

							17
The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 55.
Press and hold the MENU and a number button (1–8) 
for more than five seconds to switch between the 
codes.1
To initialize the remote control code, slide the RESET/ 
ON/ALL-OFF switch to “RESET,” and then to “ON.” The 
initial code is set to Code 1.2
MENU button
Remote Control Code
Number buttons
RESET/ON/ALL OFF Switch
Press and hold the MENU and a number button 
(1–8) that corresponds to the remote control code 
for more than five seconds to switch between 
the codes. 
Part Names and Functions 
						

							18
ADJUSTABLE FEET
Projection angle can be adjusted up to 6.5 degrees with the 
adjustable feet. 
Rotate the adjustable feet and tilt the projector to the proper 
height; to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate the 
both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button on the 
remote control or select Keystone from the menu (see pages 15, 
33, 44, 48).
Adjustable Feet
Installation 
						

							19
When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the 
sales dealer for detailed information of the optional lens specifications. 
Lens Installation
Shift the lens to the center position by using the 
Lens shift function (p. 30).1
2
Removing the lensTop cover release button
CAUTION
Be careful when handling the lens. Do not 
drop.
3
4
Top cover
Light-block sheet
Installation
While pressing the top cover release button on 
the top cover, slide the top cover toward front to 
remove it.
Slide the light-block sheet upward and remove it.
Hold the lens with one hand and pull the Lens 
Lock Lever upward with the other hand. Remove 
the lens from the projector. 
✽ Do not touch the glass part of the lens with your 
hand.
5
Turn off the projector and unplug the AC power 
cord.  
						

							20
NOTES ON LENS INSTALLATION
 ●  Do not touch or remove any parts except the lens and related parts. It may result in    
  malfunctions, electrical shock, fire hazard or other accidents.
 ●  Before installing or replacing the lens, check that the Model No. of the Projection Lens  
  matches to the projector.
 ●  For details of the lens and installation, contact the sales dealer where you purchased the 
   projector.
Fit the lens to the projector. Make sure that the 
lens is fully inserted to the projector. 
While pressing the top cover release button on the 
top cover, slide the top cover back to the projector.
1
3
Attaching the lens to the projector
Slide the light-block sheet in the groove to mount.4
Push the Lens Lock Lever downward. Make sure 
that the lens is properly locked.
5
Groove
Installation
2
Turn off the projector and unplug the AC power 
cord.