Sanyo Plc Xp200l Projector User Manual

							21
Installation
Some  parts  are  not  used  for  installation  or  replacement. 
Keep these parts for later use.
Focus Lock Screw
Focus Lock Ring
Focus adjustment 
Set up the projector and project image on the screen.
1 . Loosen the Focus Lock Screw on the lens.
2 .  Rotate  the  lens  to  obtain  proper  focus  on  center 
area of the screen. 
3 .  Lock the Focus Lock Screw securely.
When proper focus is not observed at outer area of the 
screen, proceed the following adjustments.
4 .  Loosen  the  Focus  Lock  Ring  on  the  lens.  (Turn  the 
Lock Ring counter-clockwise.)
5 .  Rotate the lens to obtain proper focus on outer area 
of the screen.
6 .  Lock  the  Focus  Lock  Ring  securely.    (Turn  the  Lock 
Ring clockwise.)
If  proper  focus  is  not  observed  over  the  entire  screen, 
repeat above adjustments 1~ 6.
Focus correction
LNS-W32
BE SURE TO CHECK FOR SAFET y
After  installing  or  replacing  the  lens,  be 
sure to check the following for safety.
1.  Check the lens is securely fixed 
with the screws.
2.   Check no wiring is damaged or 
tangled on the gear of the lens 
motor or  the other mechanical 
parts.
3.   Check  no  part  is  missing,  and 
no mounting part is loose.
When  the  lens  is  attached  to  the  projector  and  images 
are  being  projected  onto  the  screen,  the  peripheral 
focus  may  be  out  of  focus  in  some  localized  areas.  If 
this  happens,  insert  the  one,  of  three  sizes  of  spacers, 
in between the Lens Attachment and the lens to adjust 
the focus.
Inserting  the  Spacer  corrects  the  distance  on  the  Lens 
Adjustment and improves the diagonal focus.
The  corrected  distance  is  determined  by  the  thickness 
of  the  used  spacers.  As  a  guide,  the  dist ance  is 
adjusted  by  approximately  30  mm  for  each  0.1-mm 
thickness of the spacers.
There  are  three  types  of  spacers  provided,  and  there 
are  four  of  each  spacer  type.  Use  these  spacers  to 
correct the distance as required.
Spacer "1"
Color; Clear
Thickness; 0.1 mm
Spacer "2"
Color; Black
Thickness; 0.2 mm
Spacer "3"
Color; Cream
Thickness; 0.3 mm Correction distance
3 0   m m / f o r   4 0 - i n c h 
projection
Correction distance
5 5   m m / f o r   4 0 - i n c h 
projection    
Correction distance
8 0   m m / f o r   4 0 - i n c h 
projection     
B
C
D
A
BCD
ASpacer
Lens Lens Attachment
Screw driver in the lens
✔Note:
 
•	Figures	in	this	manual	may	differ	from	the	actual	product.
D
B
C
A
Distance Screen
40-inch projection 
						

							22
Monitor Output
BNC
cable
Connecting to a Computer (Digital and Analog RGB)
Monitor Output
G   B   R   H/V   V DVI-Digital 
cable VGA 
cable VGA 
cable
USB 
cable USB port
Unplug the power cords of both the 
projector and external equipment from 
the AC outlet before connecting cables.
Cables used for connection  (✽ = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.) 
• DVI-Digital Cable 
✽ 
• BNC Cable 
✽  • Serial Cross Cable
✽
• USB Cable
Monitor Output
DIGITAL INANALOG INMONITOR OUTUSB Serial Cross
cable Serial outCONTROL PORT
Installation
See the next page for the signals that can output to the 
MONITOR OUT terminal.
v
Monitor Input
v 
						

							23
RGB Scart
21-pin Output
Connecting to Video Equipment (Video, S-Video)
S-video 
cableS-video 
Output
Composite Video
Y - Pb/Cb - Pr/Cr
BNC 
cable
Unplug the power cords 
of both the projector 
and external equipment 
from the AC outlet before 
connecting cables.
Cables used for connection (✽ = Cables not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• S-VIDEO Cable ✽
• Scart-VGA Cable  
 ✽
• DVI-Digital Cable ✽
Component Video
 Output Composite Video
Component Video
 Output
(Y, Pb/Cb, Cr/Pr) Digital Output
(HDCP 
compatible)
RCA 
cable DVI-Digital 
cable Scart-VGA 
cable
Video Video
Y - Pb/Cb - Pr/CrDIGITAL INANALOG INMONITOR OUTS-VIDEO
Installation
Input TerminalMonitor OutCable
Input 1 D-sub15
RGB (PC analog)
YES
RGB (SCART) NO
DVI-D RGB (PC digital)
NO
RGB (AV HDCP) NO
Input 2 5BNC RGB
YES
Video YES
Q
Y, Cb/CrYESQ
Input 3RCA
Y, Cb/Cr
YES
Q
S-VideoS-video
NO
Video Video
YES
Q
Network NO
Monitor Out Signal Table
Refer to the 
Monitor Out 
Signal Table 
(above).
Q
A cable with one 
end D-sub 15 and 
the other end (Black 
box) compatible with 
each equipment is 
necessary.  
						

							24
Audio Output
Audio cable 
(stereo)
Connecting for Audio Signal
AUDIO IN I/II
Unplug the power cords of both the 
projector and external equipment from 
the AC outlet before connecting cables.
Cables used for connection (✽ = Cables not supplied with this projector.)
Audio Output
Installation
Audio  cable 
(stereo)
(R) (L)
AUDIO IN I/II
External Audio Equipment
Audio cable 
(stereo) Audio Input
AUDIO OUT 
(stereo)
• Audio Cable ✽
✔Note:
	 •	 	 See	 the	Sound	 menu	to	set	 the	 Input	
pattern	for	 AUDIO	IN	I/II. (p.	31)  
						

							25
This projector uses nominal input voltages of 100–120 V or 200–
240 V AC and it automatically selects the correct input voltage. It 
is designed to work with single-phase power systems having a 
grounded neutral conductor. To reduce the risk of electrical shock, 
do not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult 
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning 
on the projector. 
Connecting the AC Power Cord
Installation
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector sideAC Outlet side
To POWER CORD 
CONNECTOR on your 
projector.
Ground
To the AC Outlet.
(120 V AC)
For Continental EuropeFor the U .S .A .  and CanadaFor the U  .K .
To the AC Outlet.
(200–240 V AC)To the AC Outlet.
(200–240 V AC)
Connect  the  AC  power  cord  (supplied)  to  the 
projector.
✔Note:
	 •		Unplug 	the 	AC 	power 	cord 	when 	the 	projector 	is 	not 	in 	use.	
When 	the 	projector 	is 	connected 	to 	an 	outlet 	with 	AC 	power	
cord,	 it	is	 in	 stand-by	 mode	and	consumes	 a	little	 electric	 power.
 CAUTION
The AC  outlet  must  be  near  this  equipment  and  must  be  easily 
accessible. 
						

							26
Turning On the Projector
Connect the projector’s AC power cord into an AC 
outlet. The LAMP/SHUTTER indicator lights red and the 
POWER indicator lights green.
Press the ON/STAND-BY button on the side control 
or the ON button on the remote control. The LAMP/
SHUTTER indicator dims and the cooling fans start to 
operate. The preparation display appears on the screen 
and the countdown starts. 
2
3
116
The preparation display will disappear after 30 
seconds.
4After the countdown, the input source that was 
selected the last time and the Lamp control status icon 
(see page 55) appear on the screen.
If the projector is locked with a PIN code, PIN code 
Input Dialog Box will appear. Enter the PIN code as 
instructed below.
Selected Input Source and Lamp control
Complete peripheral connections (with a computer, 
VCR, etc.) before turning on the projector.  
What is PIN code?
PIN (Personal Identification Number) code is a security 
code that allows the person who knows it to operate the 
projector. Setting a PIN code prevents unauthorized use of 
the projector. 
A PIN code consists of a four-digit number. Refer to the PIN 
code lock function in the Setting Menu on page 57-58 for 
locking operation of the projector with your PIN code.
PIN code Input Dialog Box
Enter a PIN code
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector 
can no longer be started. Take special care 
in setting a new PIN code; write down the 
number in a column on page 83 of this 
manual and keep it on hand. Should the 
PIN code be missing or forgotten, consult 
your dealer or service center.
After the OK icon 
disappears, you can 
operate the projector.  
Lamp control status
See page 55 for the Lamp control status
✔Note:	 •	 The	Lamp	replacement	icon	and	the	Filter	 replacement	or	the	Filter	cartridge	replacement	
icon	may	appear	on	the	screen	depending	on	the	
usage	state	of	the	projector.
	 •	 When	the	filter	cartridge	replacement	icon	 keeps	appearing	on	the	screen	at	turning	on	the	
projector	for	some	time	and	no	action	is	taken	
to	replace	the	filter	cartridge,	the	projector	will	
be	automatically	shut	down	in	3	minutes	after	
turning	on	to	protect	the	projector.	(pp.	61-63,	77)
Use the Point ed buttons on the side control or Number 
buttons on the remote control to enter a number. 
When using side control
Use the Point ed buttons on the side control to select a 
number. Press the Point 
8 button to fix the number and 
move the red frame pointer to the next box. The number 
changes to “✳.” Repeat this step to complete entering a 
four-digit number. After entering the four-digit number, move 
the pointer to “Set.” Press the SELECT button so that you 
can start to operate the projector.
When using remote control
Press the Number buttons on the remote control to enter 
a number (p.15). When you complete entering a four-digit 
number, the pointer moves to “Set.” Press the SELECT 
button so that you can start to operate the projector.
 If you fixed an incorrect number, use the Point 
7 button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
If you entered an incorrect PIN code, “PIN code” and the 
number (✳✳✳✳) will turn red for a moment. Enter the 
correct PIN code all over again.
✔Note:
	 •	 When	the	Logo	select	function	is	set	to	 “Off,”	the	
logo	will	not	be	shown	on	the	screen	(p.53).
	 •	 When	the	 “Countdown	off”	or	 “Off”	is	selected	
in	the	Display	function,	the	countdown	will	not	
be	shown	on	the	screen	(p.52).
	 •	 During	the	countdown	period,	all	operations	are	 invalid.
	 •	 If	the	PIN	code	number	is	not	entered	within	3	 minutes	after	the	PIN	code	dialog	box	appeared,	
the	projector	will	be	turned	off	automatically.
	 •	 The	 “1234”	is	set	as	the	initial	PIN	code	at	the	
factory.
Basic Operation 
						

							27
Press the ON/STAND-BY button on the side control 
or the STAND-BY button on the remote control, and 
“Power off?” appears on the screen.
Press the ON/STAND-BY button on the side control or 
the STAND-BY button on the remote control again to 
turn off the projector. The LAMP/SHUTTER indicator 
lights bright and the POWER indicator turns off. After 
the projector is turned off, the cooling fans operate for 
90 seconds. You cannot turn on the projector during this 
cooling down period.
1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU 
TURN THE PROJECTOR ON, WAIT AT LEAST FIVE 
MINUTES BEFORE TURNING IT OFF.
DO NOT UNPLUG THE AC POWER CORD WHILE 
COOLING FANS ARE RUNNING OR BEFORE THE 
POWER INDICATOR LIGHTS GREEN AGAIN.
OTHERWISE IT WILL RESULT IN SHORTENING OF 
THE LAMP LIFE.
3When the projector has cooled down enough, the 
POWER indicator lights green and then you can turn on 
the projector. To unplug the AC power cord, wait until 
the projector is completely cooled down.
“Power off?” disappears after 4 seconds.
✔Note:
	 •	 When	the	On	start	function	is	set	to	“On,”	the	projector	will	be	
turned	on	automatically	by	connecting	the	 AC	power	cord	to	an	AC	
outlet	(p.56).
	 •	 The	running	speed	of	cooling	fans	is	changed	according	to	the	 temperature	inside	the	projector.
	 •	 Do	not	put	the	projector	in	a	case	before	the	projector	is	cooled	 enough.
	 •	 If	the	 WARNING	 TEMP.	indicator	blinks	red,	see	 “Warning	
Indicators”	on	page	68.
	 •	 The	projector	cannot	be	turned	on	during	the	cooling	period	with	 the	POWER	indicator	turned	off.	 You	can	turn	it	on	again	after	the	
POWER	indicator	becomes	green	again.
Turning Off the  Projector
DO NOT OPERATE THE PROJECTOR CONTINUOUSLY 
WITHOUT REST. CONTINUOUS USE MAY RESULT 
IN SHORTENING THE LAMP LIFE. TURN OFF THE 
PROJECTOR AND LET STAND FOR ABOUT AN HOUR 
IN EVERY 24 HOURS.
Basic Operation 
						

							28
Side Control
SELECT button
How to Operate the On-Screen Menu
MENU button
POINT buttons
On-Screen Menu
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer to 
the respective sections in this manual.
Use the Point 
7 8 buttons to select a Menu icon. Use 
the Point 
ed buttons to select an item in the selected 
menu.
Press the SELECT button to show the item data. Use 
the Point 
7 8 buttons to adjust the values.
To close the On-Screen Menu, press the MENU button 
again.
Press the MENU button on the side control or the 
remote control to display the On-Screen Menu.
✔Note:	 •	 The	selected	item	is	not	active	until	the	SELECT	button	is	pressed.
1
2
3
Remote Control
POINT buttons
SELECT button
MENU button
Basic Operation
Pointer(red frame )Pointer (red frame )
Press the Point 
ed buttons 
to move the pointer.
Item Menu icon
Menu bar
Item data
Press the Point 
7 8 
buttons to adjust the 
value.
Press  the  SELECT  button  here 
to display next items. Press the SELECT button here 
to display previous items.
Quit  
Exit this menu.
SELECT button 
						

							29
Menu Bar
For Computer Source
For Video Source
For detailed functions of each menu, see “Menu Tree” on pages 72-74.
Basic Operation
qw o
i
u
y
t
r
e!0
Show the selected Menu of the On-Screen Menu.
Used to select computer system (p. 38).
Used to select an image level among Standard, Real, and 
Image 1–10 (p. 42). Used to adjust the size of the image. [Normal/True/Wide/
Full screen/Custom/Keystone/Ceiling/Rear/Reset/Digital 
zoom +/–] (pp.43-44). Used to adjust the computer image. [Contrast/ Brightness/
Color management/Auto picture control/Advanced 
color/Color temp./White balance (R/G/B)/Offset (R/G/B)/
Sharpness/ Gamma/Reset/Store/Quit] (pp.49–51).
Used to adjust the parameters to match with the input signal 
format  (pp. 39-41). Used to select an input source (Input 1, Input 2, or Input 3) 
(pp. 35, 36). Used to adjust the volume, mute the sound, or switch the 
Input pattern (p. 31).
q	Guide Window
w	Input Menu
e	PC System Menu
r	PC Adjust Menu
t	Image Select Menu
y	Image Adjust Menu
u	Screen Menu
i	Sound Menu
Display the input source information (p. 32). Used to set the projector’s operating configurations 
(pp. 52-60).
o	Setting Menu
!0	Information Menu
qw o
i
u
y
t
r
e
Show the selected Menu of the On-Screen Menu.
Used to select the system of selected video source (p. 45).
Used to select an image level among Standard, Cinema, and 
Image 1–10 (p. 46). Used to adjust the size of the image. [Normal/Wide/
Custom/Keystone/Ceiling/Rear/Reset] (pp. 47-48).
Used to select an input source (Input 1, Input 2, or Input 3) 
(pp. 35, 36).
Used to adjust the volume, mute the sound, or switch the 
Input pattern (p. 31).
q	Guide Window
w	Input Menu
e	AV System Menu
r	Image Select Menu
y	Screen Menu
u	Sound Menu
Display the input source information (p. 32). Used to set the projector’s operating configurations 
(pp. 52-60).
i	Setting Menu
o	Information MenuUsed to adjust the picture image. [Contrast/Brightness/ 
Color/Tint/Color management/ Auto picture control/
t	Image Adjust Menu
Advanced color/Color temp./White balance (R/G/B)/ Offset 
(R/G/B)/Sharpness/Gamma/Noise reduction/Progressive/
Reset/Store/Quit] (pp. 49–51.)
✔Note:	 •	 Items	will	be	same	as	the	items	in	video	source	when	480i,	575i,	480p,	575p,	720p,	1035i	or	1080i	is	selected. 
						

							30
Operating with Projector Control
The following lens operation can be made with the Lens 
button on the side control. 
Press the LENS button to enter each lens operation mode. 
The selected adjustment display appears on the screen.
Display “Lens shift” on the screen. Use the Point ed7 8 
buttons to position the screen to the desired point without 
having picture distortion. 
The screen can be moved up or down to 50 percent, or 
sideways up to 10 percent from the central axis of the 
lens shift.
Lens Shift Adjustment
✔Note:
	 •	The	 arrow	disappears	 at	the	 maximum	 lens	shift	
in	each	direction.
	 •	The	 arrow	turns	red	when	 the	lens	 shift	 comes	 to	
the	center	position	of	the	screen.
Display “Zoom” on the screen. Use the Point ed buttons 
to zoom in and out the image.
Zoom Adjustment
Display “Focus” on the screen. Use the Point ed buttons 
to adjust focus of the image.
Focus Adjustment Side Control
LENS button
Lens Operation
ZOOM
FOCUS
POINT buttons
Zoom ➜ Focus ➜ Lens Shift ➜ • • • • •
Basic Operation
Shutter Function
Shutter function allows you to completely block out light 
to the screen. Press the SHUTTER button to close the 
shutter inside the projector. To open up the shutter, press 
the SHUTTER button again. Refer to p.59 for detail of 
setting for the Shutter function.
✔Note:
• 	The 	SHUTTER 	button 	on 	the 	side 	control 	and 	the	
remote 	control 	cannot 	be 	effective 	when 	Shutter	
Protection	is	"On"	in	the	Setting	menu.	(p.59)
•	 The	 LAMP/SHUTTER	 indicator	on	the	 projector's	 top	
lights	blue	when	the	shutter	is	closed.	(p.13)
• 	The 	projector 	will 	shut 	down 	automatically 	when	
the 	set 	time 	on 	shutter 	management 	has 	passed.	
(p.59)
•		 The 	Power 	management 	function 	does 	not 	work	
when	the	shutter	is	closed.(p.56)
SHUTTER button