Sanyo Plc Xf1000 Projector User Manual

71
Computer Input/Video Input
SettingLanguage
Fan control
Quit
Position/Simple Menu/Quit
Blue/User/Black
Logo select
Capture
Logo PIN code lock
Quit
Auto/Normal/Eco
12 languages provided.
Menu
Logo
Lamp control
Both/Front/Back
Normal/Max
Power management
Background
On/Off
Logo PIN code change
Quit
RC sensor
Off/Ready/Shut down
1–30 Min.
Quit
On/Off
On start
Key lock
SecurityOff
Projector
Remote Control
PIN code lock Off/On1/On2
PIN code change
Used timeFilter counter
Yes/NoFactory default
Off/Countdown...

72
Indicators and Projector Condition
Check the indicators for the projector condition. 
The projector is operating normally .
• • • on
• • • off• • •  
blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)
• • • dim
• • •  blinking slow           
(approx. 2 seconds ON, 
2 seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  
0.5 seconds OFF)
Appendix
Indicators
Projector ConditionLAMP
red READY
green WARNING
TEMP.
red WARNING
FILTER
orange SHUTTER
blue LAMP...

73
Appendix
The projector is detecting abnormal condition .
Indicators
Projector ConditionLAMPred READY
green WARNING
TEMP.
red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP.
orange
The temperature inside the projector is elevated 
close to the abnormally high level.
The temperature inside the projector is abnormally 
high. The projector cannot be turned on. When 
the projector is cooled down enough and the 
temperature returns to normal, the READY indicator 
lights green and the projector can be...

74
Appendix
The projector is detecting abnormal condition .
Indicators
Projector ConditionLAMPred READY
green WARNING
TEMP.
red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP.
orange
If the Filter counter reached a time set in the timer 
setting, a Filter replacement icon (Fig.2) appears 
on the screen and the WARNING FILTER indicator 
on the top panel lights up. Replace the filter as 
soon as possible. If the filter is out of scroll and the 
projector reaches a time set in the timer setting, Fig. 
3...

75
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below 
and less than 230 MHz of Dot Clock.
PC Adjustment can be limited when these modes are selected.
Appendix
✽
“True” cannot be selected when WUXGA1, UXGA2, UXGA3, UXGA4 and UXGA5 are selected (p.39)
ON-SCREEN DISPLA yRESOLUTION
H-Freq .(kHz)V-Freq .(Hz)
VGA 1 640x480 31.470 59.880 
VGA 2 720x400 31.470 70.090 
VGA 3 640x400 31.470 70.090 
VGA 4 640x480 37.860...

76
When an input signal is digital from the DVI terminal, refer to the chart below.
Appendix
✔Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
•Specifications are subject to change without notice.
ON-SCREEN DISPLA yRESOLUTION
H-Freq .(kHz)V-Freq .(Hz)
D-VGA 640x480 31.470 59.940 
D-480p 720x480 31.470 59.880 
D-575p 720x575 31.250 50.000 
D-SVGA 800x600 37.879 60.320 
D-XGA 1024x768 43.363 60.000 
D-WXGA 1 1366x76848.360 60.000...

77
Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  20.87” x 10.55” x 29.8” (530.0 mm x 268.0 mm x 757.0 mm)  
  Net Weight  60.85lbs (27.6 kg) 
  Feet Adjustment  0˚ to 2.8˚           
          
Panel Resolution 
 LCD Panel System  1.8” TFT Active Matrix type, 3 panels  
  Panel Resolution  1,024 x 768 dots 
  Number of Pixels  2,359,296 (1,024 x 768 x 3 panels)           
         
Signal Compatibility 
 Color System PAL, SECAM, NTSC,...

78
Optional Parts
       Model No.
Wired Remote Cable(30m)         : POA-CA-RC30 
Optional Interface Board (DVI)         : POA-MD18DVI
Optional Interface Board (5-BNC)         : POA-MD16VD1
Optional Interface Board (D-sub 15)       : POA-MD04VGA
Optional Interface Board (Dual-SDI)      : POA-MD17SDID
Optional Interface Board (Network board)      : POA-MD13NET2
Optional Interface Board (DVI / D-sub 15)      : POA-MD23ADI
Optional Interface Board (5-BNC / VIDEO)      : POA-MD25VD3
Optional Interface Board...

79
Configurations of Terminals
ANALOG (Mini D-sub 15 pin)
512341096781514131 112
Red Input
Ground (Horiz.sync.)
Green Input
No Connect
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert. sync.)
DDC Data
Ground
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
CONTROL PORT CONNECTOR (D-sub 9 pin)
No Connect
R X D
T X D
No Connect
SG
No Connect
No Connect
No Connect
Serial
1
2
3
4
5
6
7
8
DIGITAL DVI-D (DVI 24 PIN)
1917
21018
31 119
41220
51321
61422
71523...

80
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service center. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code. While the...