Sanyo Plc Xf1000 Projector User Manual

21
Installation
Connecting to Video Equipment
Video Source (example) Video Cassette Recorder Video Disc Player
RGB SCART
21-pin Output
YPb/Cb Pr/Cr
Y-Pb/Cb-Pr/Cr
Component video output equipment.  
(such as DVD player or 
high-definition TV source.)
Component Video Output 
BNC
Cable 
Digital Output
( HDCP compatible)
DVI Cable SCART-VGA
Cable
 
DIGITAL
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
S-Video Output
S-VIDEO
Cables...

22
NOTE ON THE POwER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side AC Outlet side
To POWER CORD 
CONNECTOR on your 
projector. Ground
To the AC Outlet.
(120 V AC)
For Continental EuropeFor the U
 .S .A .  and CanadaFor the U  .K .
To the AC Outlet.
(200–240 V AC) To the AC...

23
Turning On the Projector
Connect the projector’s AC power cord into an AC 
outlet and turn on the MAIN ON/OFF Switch. The 
LAMP indicator lights red and the READY indicator 
lights green.
Press the ON/STAND-BY button on the side control 
or on the remote control. The LAMP indicator 
dims red and the cooling fans start to operate. The 
preparation display appears on the screen and the 
countdown starts. 2
3 1
16
The preparation display will disappear after 20 
seconds.
4After the countdown, the input...

24
Press the ON/STAND-BY button on the side control 
or on the remote control, and “Power off?” appears 
on the screen.
Press the ON/STAND-BY button on the side control 
or on the remote control again to turn off the 
projector. The LAMP indicator lights bright and the 
READY indicator turns off. After the projector is 
turned off, the cooling fans operate. You cannot turn 
on the projector during this cooling down period.1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU 
TURN THE PROJECTOR ON, WAIT AT...

25
Side Control
SELECT button
How to Operate the On-Screen Menu
MENU button
SELECT button
POINT buttons
On-Screen Menu
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer 
to the respective sections in this manual.
Use the Point 
7 8 buttons to select a Menu icon. 
Use the Point 
ed buttons to select an item in the 
selected menu.
Press the SELECT button to show the item data. 
Use the Point 
7 8 buttons to adjust the values.
To close the...

26
Menu Bar
For Computer Source
For Video Source
Show the selected Menu of the On-Screen Menu.
Used to select computer system (p. 34).
Used to select an image level among Standard, Real, and 
Image 1–10 (p. 38). Used to adjust the size of the image. [Normal/True/Wide/
Full screen/Custom/Keystone/Ceiling/Rear/Reset/Digital 
zoom +/–] (pp.39-40).
Display the input source information (p. 28). Used to adjust the computer image. [Contrast/Brightness/
Color management/Auto picture control/Advanced 
color/Color...

27
Operating with Projector Control
Display “Lens shift” on the screen. Use the Point ed7 8 
buttons to position the screen to the desired point without 
having picture distortion. 
The screen can be moved up or down to 50 percent, or 
sideways up to 10 percent from the central axis of the lens 
shift.
Lens Shift Adjustment
✔Note:
  • The  arrow  disappears  at  the  maximum  lens  shift  in  each 
direction.
  • The  arrow  turns  red  when  the  lens  shift  comes  to  the 
center position of the...

28
Basic Operation
Information
Information display can be used to confirm the current 
operating condition of the projector and the signal being 
projected through the projector.
Press the INFORMATION button to display the 
information window on the screen. To hide the 
information window, press the INFORMATION button 
again or Point 
7 8 buttons.
The information window can also be selected from the 
menu.
Information  Menu
Information Menu
*  The H- and V-sync freq. values described in this figure 
may...

29
Operating with Remote Control
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons 
enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the FREEZE button on the remote control to freeze 
the picture on the screen. To cancel the FREEZE function, 
press the FREEZE button again or press any other button.
FREEZE button
Press the AUTO PC button on the remote control to 
operate the Auto PC Adj. function. The...

30
KEySTONE button
Reduce  the  upper  width  with 
Point e button.  Re d u c e   t h e   l owe r   w i d t h 
with Point d button. Reduce  the  left  part  with 
Point 7 button. Reduce  the  right  part  with 
Point 8 button. 
• 
The white arrows indicate that there is no correction.
•  A red arrow indicates the direction of correction.
•  An arrow disappears at the maximum correction.
•  If you press the KEYSTONE button on the remote 
control again while the Keystone dialog box is being 
displayed, the...