Sanyo Plc Hf10000l Projector User Manual

							
71

Maintenance and Care
Filter Instructions
Filter prevents dust from accumulating on the optical elements inside the projector\
. Should the filter becomes 
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup 
and adversely affect the life of the projector. This projector has an electrically operated filter which helps you to 
replace the filter easily. The projector monitors the condition of the filter at all time and replac\
es a filter with a 
new one automatically when it detects the clogging. 
If the projector reaches a time set in the timer setting (p. 
67), a Filter replacement icon (Fig.1) appears on the screen 
and the WARNING FILTER indicator on the top panel lights 
up (p.87). When you see this icon, replace the filter as soon 
as possible (pp.30, 61). If the filter is out of scroll and the 
projector reaches a time set in the timer setting, Fig. 2 
appears on the screen, indicating that the filter cartridge 
replacement is necessary.
When the filter scroll is counted down to 1, the Last scroll 
icon (Fig.3) appears on the screen, indicating that there is 
one scroll left in the filter cartridge (p.67).
If the projector detects that the filter is clogged and no scroll 
is left in the filter cartridge, a Filter cartridge replacement 
icon (Fig. 4) appears on the screen and the WARNING 
FILTER indicator on the top panel lights up (p.87). When you 
see this icon, replace the filter cartridge (p.72) and reset the 
Filter counter (p.73) and the Scroll counter (p.73).
When the filter is being scrolled by the remote control (p.30) 
or the Filter control function in the setting menu (p.61), a 
Filter replacement icon and “Please wait...” message (Fig.5) 
appear on the screen and the WARNING FILTER indicator 
blinks slow (approx. 2 seconds ON, 2 seconds OFF) (p.85).
The WARNING FILTER indicator blinks fast when the 
projector detects an abnormal condition, the filter cartridge 
is not installed properly, or the filter scroll is not working 
properly (p.87).
Fig.1   Filter replacement icon
Fig.4    Filter cartridge replacement icon
Fig.
   Last scroll icon
✔Note:
• 
Fig.1, Fig.2, Fig.3 or Fig. 4 will not appear when the Display function is set to “Off” (p.53), or during “Freeze” (p.30).
•  The filter cannot be rewound.
•  The filter can be scrolled 9 times since the filter cartridge has 
10 scrolls. 
•  The filter cartridge is disposable. Do not clean and reuse the 
filter cartridge.
•  Do not expose the filter cartridge to water or liquid, or it may 
cause a breakdown.
•  Replace the filter cartridge after all the scroll is used up. If you 
replace the filter cartridge when there are some scrolls left in the filter cartridge, the filter counter and the scroll counter do not recognize the correct number of remaining scrolls and the reset function cannot work properly. It may cause a breakdown.
•  The used part of the filter can be seen on the edge of the Filter 
cartridge after scrolling the filter, but there is no problem for the use of the projector.
Fig.5    Filter replacement icon and 
“Please wait...” message. 
• Do not use the filter cartridge with other projector. The filter counter and the scroll counter do not recognize the correct number of remaining scrolls of the used filter cartridge and the reset function cannot work properly. It may cause a breakdown.
•  Make sure that the projection lamps are turned off when you 
are replacing the filter cartridge. If you replace the filter cartridge when the projection lamps are turned on, the projector will be shut down automatically for safety purposes.
•  Do not forget to reset the filter counter and the scroll counter in 
the setting menu after replacing the filter cartridge. If you forget to reset the filter counter and the scroll counter, the projector cannot recognize the correct number of remaining scrolls and it may cause a breakdown. 
•  When the projector is kept used for 3 minutes without getting 
the filter cartridge replaced after the Fig.4 appears on the screen, the projector is turned off automatically to prevent the damage of optical components.
Fig. 
						

							
7

Maintenance and Care
Turn off the projector, press the Main On/Off Switch to 
Off and unplug the AC power cord from the AC outlet.
First, clean up the dust on the projector and around the 
air vents.
1
2
Slide and open the Filter cover. (See the right figure.)3
Put the new one back into the position and close 
the filter cover. Make sure that the filter cartridge is 
properly and fully inserted.
5
CAUTION
Make sure the filter cartridge is inserted in the 
projector. If the filter cartridge is not inserted, the 
projector cannot be turned on. 
Do not put anything into the air vents. Doing so 
may result in malfunction of the projector.
4
Reset the filter counter and the scroll counter (p.73).
6
Filter cover
Replacing the Filter Cartridge
Pull out the filter cartridge by holding the finger grip.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when 
operating the projector. Usage in these environments may 
cause a poor image quality.
When using the projector under dusty or smoky conditions, 
dust may accumulate on a lens, liquid crystal panels, or optical 
elements inside the projector. Such condition may degrade the 
quality of the projected image.
When the symptoms above are noticed, contact your authorized 
dealer or service center for proper cleaning.
ORDER REPLACEMENT FILTER CARTRIDGE
Replacement  filter  cartridge  can  be  ordered  through  your 
dealer. When  ordering,  give  the  following  information  to  the 
dealer.
 l  Model No. of your projector
      PLC-HF10000L
 l  Replacement Filter Cartridge 
      Type No. : POA-FIL-1 0
                       
(Service Parts Code: 610 5 90)
Connect  the  AC  power  cord  to  the  projector  and  turn 
on the projector.
7
Filter cartridge 
						

							
7

Maintenance and Care
Filter counterBe sure to reset the Filter counter after replacing the filter 
cartridge.
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Setting and 
then press the Point 8 or the SELECT button.
Use the Point ed buttons to select Filter counter and 
then press the SELECT button. Use the Point ed 
buttons to select Filter counter reset and then press 
the SELECT button. Filter counter Reset? appears. 
Select Yes to continue.
1

Filter counter Reset? 
appears.
Select Yes, then another 
confirmation box 
appears.
Select Yes again to reset 
the Filter counter.
Another confirmation dialog box appears, select Yes to 
reset the Filter counter.
Resetting the Filter Counter
Be sure to reset the Scroll counter after replacing the filter 
cartridge. 
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Setting and 
then press the Point 8 or the SELECT button.
Use the Point ed buttons to select Filter counter and 
then press the SELECT button. Use the Point ed 
buttons to select Scroll counter reset and then press 
the SELECT button. Scroll counter Reset? appears. 
Select Yes to continue.
Scroll counter
Another confirmation dialog box appears, select Yes to 
reset the Scroll counter.
Scroll counter Reset? 
appears.
Select Yes, then another 
confirmation box 
appears.
Select Yes again to reset 
the Scroll counter.
Resetting the Scroll Counter
1

 
						

							
74

Maintenance and Care
Lamp Management
This Projector is equipped with 2 Projection Lamps to ensure brighter image and those lamps are controlled \
by 
the Lamp Management Function. The Lamp Management Function detects the status of lamps and shows the 
status on screen or on the LAMP 1/2 REPLACE indicators. This function also automatically controls the Lamp 
Mode when any of lamps is out for the end of life or malfunctions. 
Projection Lamp lights normally.
Lamp 1/ Replace Indicators
The LAMP 1/2 REPLACE indicators light orange when any of Projection Lamps is nearing its end, and flash 
when any of them becomes out. Check the number of lamp on the Lamp Status Display or the LAMP 1/2 
REPLACE indicators and replace the lamp.yellow Lamp
Dim Lamp
X Mark on Lamp
Red Lamp
LAMP 1/2 REPLACEINDICATORS
Projection Lamp is turned off.
Projection Lamp is nearing its end. When the image 
becomes darker or the color becomes unnatural, replace 
lamp. (LAMP 1/2 REPLACE indicator lights orange.)
(LAMP 1/2 REPLACE indicator flashes orange.)
Projection lamp is defective or fails to be turned on. 
Restart the projector on, and make sure lamp is on. If 
this mark still appears, replace lamp corresponding with 
number marked X.
LAMP STATUSDISPLAY
Lamp Mode Changeover
The Lamp Management Function automatically changes the lighting lamp (Lamp Mode) by detecting the status of lamp. 
When either of the 2 lamps is out, the projector operates with 1 lamp. The Lamp Mode can be switched to 2 lamps or 1 
lamp manually. Refer to the SETTING section on pages 54, 55.
2 LAMPS MODE1 LAMP MODE
Lamp Status Display
The Lamp Status Display appears on screen when the projector is turned on or the input position (input 1, input 
2, Input 3 or input 4) is switched. This shows the status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to 
the following for each status.
Lamp status
When Lamp 1 is burnt out.
When Lamp 2 is burnt out. 
						

							
75

Maintenance and Care
Check the number of lamp to be replaced on the Lamp 
Status Display.
Loosen a screw on the Lamp Cover. Slide and open the 
Lamp Cover. (See the right figure.)
1
3
Loosen two screws and pull out the Lamp to be replaced 
by grasping handle.4
Turn off the projector, press the Main On/Off Switch to Off 
and unplug the AC power cord from the AC outlet. Let the 
projector cool for at least 45 minutes.
2
Replace the Lamp with a new one and tighten two 
screws.  Make sure the Lamp is set properly.
6
Follow these steps to replace the lamp.
Put the Lamp Cover back and tighten a screw. 
5
SCREW
LAMP 
COVER
Make sure which number of lamp needs to be 
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 1.
CAUTION :  DO NOT OPERATE THE PROjECTOR WHILE 
ANy OF LAMPS IS REMOVED. IT MA y 
RESULT IN MALFUNCTIONS, FIRE HAZARD, 
OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To  maintain  quality  of  picture  (better  balance  of  color 
and  brightness  in  entire  screen),  we  recommend 
replacing both  lamps at a time. 
Lamp Replacement
For continued safety, replace with a lamp assembly 
of the same type.
Do not drop the lamp assembly or touch a glass 
bulb! The glass can shatter and may cause injury.
Allow the projector to cool, for at least 45 minutes 
before you open Lamp Cover.  The inside of the 
projector can become very hot.
CAUTION
TURN OFF THE UV LAMP BEFORE 
OPENING THE LAMP COVER.
WARNING:
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the 
screen and LAMP 1/2 REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing 
when the LAMP 1/2 REPLACE indicators should light is depending on the lamp mode.
Indicators
LAMP 1 /  REPLACE indicators
Lamp replacement icon
✔Note: • The Lamp replacement icon will not appear when the Display function is set to “Off” (p.53), or during “Freeze” (p.30).
SCREWS
LAMP 2
LAMP 1 
						

							
76

This projector uses a high-pressure lamp which must be handled carefully and properly. 
Improper handling may result in accidents, injury, or create a fire hazard.
l Lamp  lifetime  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use. There  is  no 
guarantee  of  the  same  lifetime  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  lifetime  in  a 
shorter period of time than other similar lamps.
l If  the  projector  indicates  that  the  lamp  should  be  replaced,  i.e.,  if  the  LAMP  1/2  REPLACE  indicators 
light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow 
carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp 
with the LAMP 1/2 REPLACE indicators lighted may increase the risk of lamp explosion.
l Lamp  may  explode  as  a  result  of  vibration,  shock  or  degradation  as  a  result  of  hours  of  use  as  its 
lifetime  draws  to  an  end.  Risk  of  explosion  may  differ  according  to  the  environment  or  conditions  in 
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFET y PRECAUTIONS SHOULD BE TAKEN.
If  a  lamp  explodes,  disconnect  the  projector’s  AC  plug  from  the  AC  outlet  immediately.  Contact  an 
authorized  service  center  for  a  checkup  of  the  unit  and  replacement  of  the  lamp.  Additionally,  check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from  the  cooling  air  circulation  holes.  Any  broken  shards  found  should  be  cleaned  up  carefully.  No  one 
should  check  the  inside  of  the  projector  except  those  who  are  authorized  trained  technicians  and  who 
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.
          LAMP HANDLING PRECAUTIONS
Maintenance and Care
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following 
information to the dealer.
 l  Model No. of your projector   :  PLC-HF10000L
 l  Replacement Lamp Type No.  :  POA-LMP146
               (Service Parts No. 610 351 5939) 
						

							
77

Maintenance and Care
Turn off the projector, press the Main On/Off Switch to Off 
and unplug the AC power cord from the AC outlet before 
cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens 
cleaner, or use a lens cleaning paper or commercially 
available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the lens.
Cleaning the Projector Cabinet
Turn off the projector, press the Main On/Off Switch to Off 
and unplug the AC power cord from the AC outlet before 
cleaning.
Gently wipe the projector body with a soft dry cleaning 
cloth. When the cabinet is heavily soiled, use a small amount 
of mild detergent and finish with a soft dry cleaning cloth. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the cabinet.
When the projector is not in use, put the projector in an 
appropriate carrying case or cover to protect it from dust and 
scratches.
Cleaning the Projection Lens
CAUTION
Do not use any flammable solvents or air sprays 
on the projector and in its vicinity. The explosion or 
fire hazard may occur even after the AC power cord 
is unplugged because the temperature inside the 
projector is extremely high due to the lamps. 
In addition, there is a risk that the internal parts 
may be damaged not only by the flammable air 
spray but also by the cold air. 
						

							
7

Maintenance and Care
The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING TEMP. indicator and the LAMP indicator to take proper maintenance. 
Warning Indicators
The projector is shut down and the WARNING TEMP. 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut down 
to protect the inside of the projector. The LAMP indicator 
turns red brighter and the WARNING TEMP indicator 
blinks while the projector is being cooled down. When the 
projector has cooled down enough (to its normal operating 
temperature), it can be turned on again by pressing the ON/
STAND-BY button.
✔Note:
• The WARNING TEMP. indicator continues to blink even after the temperature inside the projector returns to normal. When the projector is turned on again, the WARNING TEMP. indicator stops blinking. 
Then check the matters below:
–   Did you provide appropriate space for the projector to be 
ventilated? Check the installing condition to see if the air 
vents of the projector are not blocked.
–   Has the projector been installed near an Air-Conditioning/ 
Heating Duct or Vent? Move the installation of the 
projector away from the duct or vent.
–   Is the filter clean? Replace the filter with a new one.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN FIRE 
OR ELECTRIC SHOCK.
Indicators
Indicators
WARNING TEMP.
blinking red
The projector is shut down; and the LAMP indicator is 
lighting and other indicators are blinking.
When the projector detects an abnormal condition, it 
will be automatically shut down to protect the inside of 
the projector and the LAMP indicator lights on and other 
indicators blink. In this case, unplug the AC power cord and 
plug it, and then turn on the projector once again to verify 
operation. If the projector cannot be turned on and these 
indicators are still lighting and blinking, unplug the AC power 
cord and contact the service center.
LAMP indicator lights on 
and other indicators blink. 
						

							
79

Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–21.
2.  Check the cable connection. Make sure that all computers, video equipment, and power cords are properly 
connected.
3.  Make sure that all power is switched on.
4.  If the projector still does not produce an image, restart your computer.
5.  If an image still does not appear, disconnect the projector from your computer and check your computer 
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector. 
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the 
projector. Turn on equipment in the order of the projector and computer.)
6.  If a problem still persists, check the following solutions.
Appendix
Problem:Solutions
No power.
– Plug the power cord of the projector into the AC outlet.
– Turn the MAIN ON/OFF switch to ON.
– Press the ON/STAND-BY Button to ON.
– Make sure the POWER indicator lights.
–  Check  the  indicators.  If  the  LAMP  indicator  lights  and  the  other  indicators  blink,  the 
projector cannot be turned on. (Refer to page 78.)
– Check the projection lamp. (Refer to pages 75, 76.)
– Unlock the ley lock function. (See page 63)
PIN code dialog box appears 
at start-up.
–  PIN code lock is being set. Enter a PIN code; the “1234” or numbers you have set (see 
pages 24, 63, 64)
The initial display is not 
shown.
– Make sure “Off ” or “Countdown Off” are not chosen at Display function.
   (See page 53)
The initial display is not 
same with the default one.
– Make sure “User” or “Off” are not chosen at Logo select function.
   (See page 59)
When the projector is on and 
you press the input button, 
an icon other than the Lamp 
mode icon appears.
–  That is the Filter warning icon. Refer to page 71.
An icon other than Input 
mode or Lamp mode icon 
appears.
–   That is the Lamp replacement icon or the Filter warning icon. See pages 71, 75.
No image.
– Check the connection between your computer or video equipment and the projector.
–  See if the input signal is correctly output from your computer. Some laptop computers 
may  need  to  be  changed  the  setting  for  monitor  output  when  connected  to  the 
projector. See your computer’s instruction manual for the setting.
– It takes about 20 seconds to display an image after turning on the projector.
– See if the selected system is corresponding with your computer or video equipment.
–  Select correct input source once again through menu operation (See pages 32-34).\
–   Make  sure  the  temperature  is  not  out  of  Operating Temperature
  (41˚F–104˚F  [5˚C–
40˚C]).– Make sure that the shutter is open. (See pages 28, 65） 
						

							
0

 
appears on the screen
–  The end of lamp life is approaching. Replace the lamp with a new one promptly.
   (See page 75)
appears on the screen
–  The filter is out of scroll. Replace the filter cartridge with a new one promptly.
   (See pages 71-73)
The image is out of focus.
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
 ✔Note:  Moving  the  projector  from  a  cool  temperature  location  to  a  warm  temperature 
location  may  result  in  moisture  condensation  on  Projection  Lens.  In  such  cases, 
leave the projector OFF and wait until condensation evaporates.
–   Projecting from excessive slant angle to the screen may cause keystone distortion and 
partial imperfect focus.
The image is not bright 
enough.
– Check if “Contrast” or “Brightness” are adjusted properly. (See pages 40, 48) 
– Check if “Image level” is selected properly. (See pages 39, 47)
– Check the Lamp control function. ( See “SETTING” section on page 54)
–  Check  the  Lamp  1/2  Replace  indicators.  If  it  lights,  the  end  of  lamp  life  is  approaching. 
Replace the lamp with a new one promptly. (See page 75)
–    The  image  is  darker  when  1  lamp  mode  is  selected,  compared  with  2  lamp  mode. 
Check the lamp mode at SETTING section on page 54. 
The color is strange.– Check the Input signal, color system, video system, or computer system mode.
The image is Left/Right 
reversed.– Check the Ceiling / Rear function. (See pages 45, 52)
The image is Top/Bottom 
reversed.– Check the Ceiling function. (See pages 45, 52)
The image is distorted or 
runs off.– Check “PC Adjust” menu or “ Screen” menu and adjust them.
Auto PC adjustment function 
does not work.
–   Check  the  Input  signal.  Auto  PC  Adjustment  function  cannot  work  when  480p,  575p, 
720p,  480i,  575i,  1035i,  1080p,  or  1080i  is  selected  or  when  the  digital  signal  is  input 
into HDMI/DVI-D terminal. (See page 36) 
Some displays are not seen 
during the operation.– Check the Display function (see page 53).
The setting does not remain 
after turning off power.
–  Make  sure  you  selected  “Store”  after  adjusting  settings.  Some  settings  cannot  be 
stored if not registered with “Store”.
Power management function 
does not work.
–  Power  management  function  cannot  work  while  “Freeze”  function  is  running  or  the 
shutter is closed.
Image disappears 
automatically.
–  Check  the  power  management  function  in  the  Setting. The  power  management  is  set 
to "On" at the factory.
Capture function does not 
work.
– Check the connection to see if there is signal.
–  Capture  function  is  not  available  when  the  Picture  in  Picture  function  is  set  to  one  of 
User1 - 5.
Some menus cannot be 
selected.– Each of the Video Input and Computer Input has a limit on selectable menus.
Appendix