Sanyo Plc Hf10000l Projector User Manual

							
1

WARNING: 
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector 
or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem. We  will  advise  you  how  to  obtain 
service.
Appendix
The shutter does not 
work.– Check “Protection” or “Release Key” of the shutter function. (See page 65)
The power is turned off 
automatically.
–  Power  management  function  runs  by  initial  setting.  Check “SETTING”  section  on  page 
62.
–   
When  the  filter  cartridge  replacement  icon  keeps  appearing  on  the  screen  at  turning 
on the projector for some time and no action is taken to replace the filter cartridge, the 
projector  will  be  automatically  shut  down  in  3  minutes  after  turning  on  to  protect  the 
projector. (See pages 71, 87)
–   Do not cover the ventilation slots on the projector. (See pages 4, 6)
–   Projector  may  be  used  in  high  ambient  temperature  environment.  Make  sure  the 
temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–40˚C]). (See page 78)
You cannot operate with 
the side control.
–  
The  side  control  is  not  available  If  the  side  control  is  locked  at  “Key  lock”  under 
“Security” of SETTING section. Please check “SETTING” section on page 63.
The Remote Control does 
not work.
– Check the batteries.
– Check if the RC sensor is set properly. (See page 61)
– Make sure no obstruction is between the projector and remote control.
–  Make sure you are not too far from the projector when using the remote control.
     Maximum operating range is 16.4’ (5m).
–   Make sure that the remote control code conforms to the projector’s code. 
   (See page 61.)
–   Check if the ON/ OFF switch on the remote control is set to ON.
– Unlock the Key lock function for the remote control. (See page 63)
–   Wireless remote control does not work when the remote control cable is connected to 
the projector. (See page 15)
Indicators blinks or lights.–   Check  the  status  of  the  projector  with  referring  to  “  INDICATORS  AND  PROJECTOR 
CONDITION” on pages 85-87.
appears on the screen
– Your operation is invalid. Operate correctly.
Unable to unlock the Logo 
PIN code lock, Security 
key lock or Security PIN 
code lock.
– Contact the dealer where you purchased the projector or the service center.
Forget the Logo PIN code 
or Security PIN code. – Contact the dealer where you purchased the projector or the service center.
When brightness (Current 
value) continuously 
goes down to a certain 
rate from Target value in 
Constant mode.
–  Check  the  lamp  status  and  replace  the  lamp,  or  decrease Target  value  in  Constant 
mode. 
						

							


Menu Tree
InputRGB (PC analog)RGB (Scart)RGB (PC digital)RGB (AV HDCP)
Input 3
RGB
VideoS-video
Input 2
✔Note:
•The Menu display varies depending on the input signal.
Appendix
Input 4
(For Optional Interface Boards)
(For Optional Interface Boards)
HDMI
Computer Input/HDMI Input/Video Input
Input 1
Projector
Information
Remote control
EffectRelease key
InputH-sync freq.V-sync freq.
Key lock
Screen
Language
Lamp mode
Power management
Lamp 1
PIN code lock
Lamp 2
Lamp controlLamp interval
Filter counter
Remote controlSERIAL NO.
Shutter management
Input
Y, Pb/Cb,Pr/Cr
Computer Input
Image select
Image 1 - Image 10
Standard
0–630–63
0-15
Image adjustContrastBrightness
RedGreenBlue
Sharpness
ResetStore
Gamma
0–630–630–63
0–31 
Image 1 - Image 10Yes / No
Colormanagement
Auto picture controlOff/L1/L2
Color temp.Color temp.
OffsetRed/Green/Blue
COLORGAMMA
COLOR M.MENU
MidLowMENU
Advanced colorAuto/Off
SVGA 2SVGA 3
Mode 10SVGA 1
Mode 1
LIST
HighMidLowHighAdj.
XLowLowMid
PC AdjustAuto PC adj.
Total dotsPosition HPosition V
0–31
Current modeH-sync freq.V-sync freq.
ClampDisplay area HDisplay area VResetMode freeYes/NoMode 1 - Mode 10
Mode 1 - Mode 10Store
ScreenNormal
Rear
Keystone
Ceiling
Screen aspect
Full
Reset
Scale
Position
H / VOn/OffH / V
Wide (16:9)
Custom adj.
H & V
Zoom
On/OffOn/Off
Full/16:9/16:10/4:3
Yes/No
Dynamic
Fine sync.
True
Custom
Digital zoom+Digital zoom-
System (1)
COLOR M.
ALL DEL
Real
Option control No.
Corner correctionStandard
Corner patternStoreRed/White/Blue/OffStore/Reset
CommonReset 
						

							


HDMI Input/Video Input
0–630–63
0-15
Image adjustContrastBrightness
RedGreenBlue
Sharpness
Noise reductionProgressive
Gamma
0–630–630–63
0–31 
Off/On/FilmOff/ On
Color management
Auto picture controlOff/L1/L2
Color temp.Color temp.
OffsetRed/Green/Blue
COLORGAMMA
COLOR M.MENU
MidLowCOLOR M.MENU
Advanced colorAuto/Off
LIST
HighMidLowHighAdj.
XLowLowMid
ResetStoreImage 1 - Image 10
Yes / No
Video Input
System ()Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System ()Auto
1080i
1035i
720p
575p
480p
575i
480i
1080p
Image select
DynamicImage 1 - Image 10
StandardCinema
ScreenNormal
Rear
Keystone
Ceiling
Screen aspect
Full
Reset
Aspect
Wide (16:9)
Custom adj.
Zoom
On/OffOn/Off
Full/16:9/16:10/4:3
Yes/No
Natural Wide
Custom
Corner correctionStandard
Corner patternStore
Appendix
ColorTint
Position H
Common
Scale V
Scale H
Position V
H & V
Reset
Red/White/Blue/OffStore/Reset
ALL DEL
On/Off 
						

							
4

Appendix
Fan control
1–30 Min.
Position
12 languages
Background
Display
Lamp mode2-Lamps
Edge blendingOn/Off
All
On/Off
Black level
Test pattern
Reset
Color matching
Lamp interval
Menu off
Remote controlRC sensor
Power management
Setting
Menu sizeNormalDoubleOnCountdown OffOffBlueUserBlack
TargetCurrentConstant mode1-Lamp
AutoNormal
Eco1Eco2
Lamp controlLamp control
Lamp life controlMode1
OffMode 2
Picture in PicturePicture in Picture
Language
Menu
Off/User 1 - User 5
ModeP in P/P by P
24H/200H/500H/1000H/2000H
InputMain picture/Sub pictureSourceSizePosition
Main picture/Sub pictureFrame lock
Yes/No
Yes/No
Yes/No
Store
ResetMode freeBackLeft/Right Start
R/G/B
Yes/NoBack
On/Off
Auto test patternOn/Off
Reset
Store
Advanced color matching
Back
Measured
Auto test patternTarget
Menu off
Factory default
ResetStore
Test pattern
Back
HDMI setupNormal
Filter controlYes/No
Normal/MaxCode 1 - Code 8Both/Front/BackReady/Shut down/Off
TimerDirect onOn/OffSecurityKey lock Off/Projector/Remote controlOff/On1/On2PIN code lockPIN code changeProjector ID1-999ProtectionRemote control/ProjectorOff/L1/L2EffectAny/SHUTTERRelease keyManagement
Shutter
Video delay controlOff/Low/Mid/HighClosed captionClosed captionOff/CC1/CC2/CC3/CC4ColorColor/WhiteFilter counterOff/400H/700H/1000HFilter counter resetYes/No
Filter counterTimer
Scroll remainingScroll counter reset
Test patter8 test patternsYes/NoFactory default
Logo selectLogo
Logo PIN code change
CaptureLogo PIN code lockOn/OffYes/No
Off/Default/User
R/G/B/C/M/Y/W
On/Off
Top/Bottom Start
Top/Bottom Width
Left/Right Width
Enhanced
1-180TimerStart/Stop/RestartReset
Count down
Exit
P-TimerCount up
5-480
Computer Input/HDMI Input/Video Input
Red/Green/Blue/White
Red/Green/Blue/White
Yes/No
On/Off
Measured Information 
						

							
5

Appendix
Indicators and Projector Condition
Check the indicators for the projector condition.
The projector is operating normally.
• • • on
• • • off• • •  
blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)• • • dim
• • •  blinking slow           
(approx. 2 seconds ON, 
2 seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  
0.5 seconds OFF)
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMP 1/2REP. 
orange
The projector is off. (The main On/Off switch is OFF 
position or the AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/
STAND-BY button to turn on the projector.
The projector is operating normally.
(The Shutter is open)
The projector is operating normally.
(The Shutter is closed)
The projector is preparing for stand-by or the 
projection lamp is being cooled down. The projector 
cannot be turned on until cooling is completed and 
the POWER indicator lights green.
The projection lamp is being cooled down in the 
Power management mode.
The projector is in the Power management mode.
The projection lamp is being cooled down in the 
Shutter management mode.
The projector is in the Shutter management mode. 
Press the ON/STAND-BY button to turn on the 
projector.
The filter is scrolled using the FILTER button on 
the remote control or the Filter control function in 
the setting menu. When the filter is being scrolled, 
the Filter replacement icon and “Please wait...” 
message (Fig. 1) appear on the screen.
✽
✽
✽
✽
Fig.1    Filter replacement icon and “Please wait...”
✽
✽
✽
✽
✽✽
✽
✽
✽✽
✽
✽
✽
✽
✽✽
✽• • • Differs according to conditions.
✽ 
						

							
6

Appendix
The projector is detecting abnormal condition.
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMP 1/2REP.
orange
The temperature inside the projector is elevated 
close to the abnormally high level.
The temperature inside the projector is abnormally 
high. The projector cannot be turned on. When 
the projector is cooled down enough and the 
temperature returns to normal, the POWER 
indicator lights green and the projector can be 
turned on. (The WARNING TEMP. indicator keeps 
blinking.) 
The projector has been cooled down enough and 
the temperature returns to normal. When turning on 
the projector, the WARNING TEMP. indicator stops 
blinking. Check and replace the filter.
The lamp cannot light up. (The projector is preparing 
for stand-by or the projection lamp is being cooled 
down. The projector cannot be turned on until 
cooling is completed.)
The lamp cannot light up. (The lamp has been 
cooled down enough and the projector is in stand-
by mode and ready to be turned on with the ON/
STAND-BY button.)
When either of the 2 lamps is out, the projector 
operates with 1 lamp.
The lamp has been used overtime. Replace the 
lamp immediately.
✽
✽
✽
✽
✽
✽
✽
 When the filter detects clogging, reaches a time set in the timer setting or runs out of the filter scroll, the WARNING 
FILTER indicator lights orange. When this indicator lights orange, replace the filter or the filter cart\
ridge with a new 
one promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.73). 
✽
✽
✽
✽
✽
✽
✽
✽
✽✽
✽✽✽✽
WARNING FILTER
 When the LAMP 1 REPLACE indicator and the LAMP 2 REPLACE indicator light orange, replace the projection lamps 
with new ones promptly. See page 75.
LAMP REPLACE 1 and   
						

							
7

Appendix
The projector is detecting abnormal condition.
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMP 1/2REP.
orange
If the Filter counter reached a time set in the timer 
setting, a Filter replacement icon (Fig.2) appears 
on the screen and the WARNING FILTER indicator 
on the top panel lights up. Replace the filter as 
soon as possible. If the filter is out of scroll and the 
projector reaches a time set in the timer setting, Fig. 
3 appears on the screen and the WARNING FILTER 
indicator lights up. Replace the filter cartridge as 
soon as possible.
If the filter is clogged and no scroll is left in the filter 
cartridge, a Filter cartridge replacement icon (Fig.4) 
appears on the screen and the WARNING FILTER 
indicator lights up. Replace the filter cartridge as 
soon as possible.
✔Note: • Fig.2, Fig.3 and Fig.4 icon will not appear when the Display function is set to “Off” (p.53), or during “Freeze” (p.30).
The projector detects an abnormal condition during 
filter scroll.
The projector is being cooled down after detecting 
an abnormal condition during filter scroll.
The projector has been cooled down enough and is 
in the stand-by mode after detecting an abnormal 
condition during filter scroll.
The filter cartridge is not installed in the projector. 
Check the filter compartment to see if the filter 
cartridge is installed in the projector. When the filter 
cartridge is installed and the indicators continue to 
light and blink, read the column below.
The projector detects an abnormal condition and 
cannot be turned on. Unplug the AC power cord and 
plug it again to turn on the projector. If the projector 
is turned off again, unplug the AC power cord and 
contact the dealer or the service center. Do not 
leave the projector on. It may cause an electric 
shock or a fire hazard.
The shutter is out of control. 
The shutter is out of control. (The projector is in the 
cooling mode.)
The shutter is out of control. (The projector is in the 
stand-by mode.) In that case, contact the service 
center immediately.
Fig.    Filter replacement icon
Fig.4    Filter cartridge replacement icon
Fig.
✽
✽✽
✽
✽
✽✽✽✽✽
✽
✽
✽✽
✽
✽
✽
✽ 
						

							


Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below 
and less than 230 MHz of Dot Clock.
✽
✔Note:
• Alphabet letter "i" placed beside some of the resolutions represents interlace signa\
l.
       “True” cannot be selected.
✽
✽
✽
✽
✽
ON-SCREEN DISPLA yRESOLUTIONH-Freq. 
(kHz)
V-Freq. 
(Hz)
VGA 1640x48031.470 59.880 
VGA 2720x40031.470 70.090 
VGA 3640x40031.470 70.090 
VGA 4640x48037.860 74.380 
VGA 5640x48037.860 72.810 
VGA 6640x48037.500 75.000 
VGA 7640x48043.269 85.000 
MAC LC13640x48034.970 66.600 
MAC 13640x48035.000 66.670 
480p640x48031.470 59.880 
575p768x57531.250 50.000 
575i768x576 i15.625 50.000 
480i640x480 i15.734 60.000 
SVGA 1800x60035.156 56.250 
SVGA 2800x60037.880 60.320 
SVGA 3800x60046.875 75.000 
SVGA 4800x60053.674 85.060 
SVGA 5800x60048.080 72.190 
SVGA 6800x60037.900 61.030 
SVGA 7800x60034.500 55.380 
SVGA 8800x60038.000 60.510 
SVGA 9800x60038.600 60.310 
SVGA 10800x60032.700 51.090 
SVGA 11800x60038.000 60.510 
MAC 16832x62449.720 74.550 
XGA 11024x76848.360 60.000 
XGA 21024x76868.677 84.997 
XGA 31024x76860.023 75.030 
XGA 41024x76856.476 70.070 
XGA 51024x76860.310 74.920 
XGA 61024x76848.500 60.020 
XGA 71024x76844.000 54.580 
XGA 81024x76863.480 79.350 
XGA 91024x768 i36.000 87.170 
XGA 101024x76862.040 77.070 
XGA 111024x76861.000 75.700 
XGA 121024x768 i35.522 86.960 
XGA 131024x76846.900 58.200 
XGA 141024x76847.000 58.300 
XGA 151024x76858.030 72.000 
MAC 191024x76860.240 75.080 
SXGA 11152x86464.200 70.400 
SXGA 21280x102462.500 58.600 
SXGA 31280x102463.900 60.000 
SXGA 41280x102463.340 59.980 
SXGA 51280x102463.740 60.010 
SXGA 61280x102471.690 67.190 
SXGA 71280x102481.130 76.107 
SXGA 81280x102463.980 60.020 
SXGA 91280x102479.976 75.025 
SXGA 101280x96060.000 60.000 
SXGA 111152x90061.200 65.200 
SXGA 121152x90071.400 75.600 
SXGA 131280x1024 i50.000 86.000 
ON-SCREEN
 DISPLA yRESOLUTIONH-Freq. 
(kHz)
V-Freq. 
(Hz)
SXGA 141280x1024 i50.000 94.000 
SXGA 151280x102463.370 60.010 
SXGA 161280x102476.970 72.000 
SXGA 171152x90061.850 66.000 
SXGA 181280x1024 i46.430 86.700 
SXGA 191280x102463.790 60.180 
SXGA 201280x102491.146 85.024 
SXGA+ 11400x105063.970 60.190 
SXGA+ 21400x105065.350 60.120 
SXGA+ 31400x105065.120 59.900 
SXGA+ 41400x105064.030 60.010 
SXGA+ 51400x105062.500 58.600 
SXGA+ 61400x105064.744 59.948 
SXGA+ 71400x105065.317 59.978 
MAC 211152x87068.680 75.060 
MAC1280x96075.000 75.080 
MAC1280x102480.000 75.080 
WXGA 11366x76848.360 60.000 
WXGA 21360x76847.700 60.000 
WXGA 31376x76848.360 60.000 
WXGA 41360x76856.160 72.000 
WXGA 61280x76847.776 59.870 
WXGA 71280x76860.289 74.893 
WXGA 81280x76868.633 84.837 
WXGA 91280x80049.600 60.050 
WXGA 101280x80041.200 50.000 
WXGA 111280x80049.702 59.810 
WXGA 121280x80063.980 60.020 
 WUXGA 11920 x 120074.556 59.885 
 WUXGA 21920 x 120074.038 59.950 
 WSXGA+ 11680 x 105065.290 59.954 
 WXGA+ 11440 x 90055.935 59.887 
 WXGA+ 21440 x 90074.918 60.000 
UXGA 11600x120075.000 60.000 
UXGA 21600x120081.250 65.000 
UXGA 31600x120087.500 70.000 
UXGA 41600x120093.750 75.000 
UXGA 51600x1200106.250 85.000 
720p1280x72045.000 60.000 
720p1280x72037.500 50.000 
1035i1920x1035 i33.750 60.000 
1080i1920x1080 i33.750 60.000 
1920x1080 i28.125 50.000 
1080p1920x108033.750 30.000 
1920x108028.125 25.000 
1920x108027.000 24.000 
1920x108067.500 60.000 
1920x108056.250 50.000 
1080psf/301920x108033.750 60.000 
1080psf/251920x108028.125 50.000 
1080psf/241920x108027.000 48.000  
						

							
9

Appendix
When an input signal is digital from the HDMI or DVI-D terminal, refer to the chart below.
ON-SCREEN DISPLA yRESOLUTIONH-Freq. 
(kHz)
V-Freq. 
(Hz)
D -VGA640x48031.470 59.940 
D - 480i720x480 i15.73460.000
D - 575i720x576 i15.62550.000 
D - 480p720x48031.470 60.000 
D - 575p720x57531.250 50.000 
D -SVGA800x60037.879 60.320 
D -XGA1024x7684 3.363 60.000 
D -W XGA 11366x76848.360 60.000 
D -W XGA 21360x76847.700 60.000 
D -W XGA 31376x76848.360 60.000 
D -W XGA 41360x76856.160 72.000 
D -W XGA 51366x76846.500 50.000 
D -W XGA 61280x76847.776 59.870 
D -W XGA 71280x76860.289 74.893 
D -W XGA 81280x76868.633 8 4.837 
D -W XGA 91280x80049.600 60.050 
D -W XGA 101280x80041.200 50.000 
D -W XGA 111280x80049.702 59.810 
D -W XGA 121280x80063.980 60.020 
D -SXGA 11280x102463.980 60.020 
D -SXGA 21280x102460.276 58.069 
D -SXGA+ 11400x105063.970 60.190 
D -SXGA+ 21400x105065.350 60.120 
D -SXGA+ 31400x105065.120 59.900 
D -SXGA+ 41400x105064.030 60.010 
D -SXGA+ 51400x105062.500 58.600 
D -SXGA+ 61400x105064.74 4 59.948 
D -SXGA+ 71400x105065.317 59.978 
D - UXGA1600x120075.00060.000
ON-SCREEN
 DISPLA yRESOLUTIONH-Freq. 
(kHz)
V-Freq. 
(Hz)
 D -WUXGA 21920x120074.038 59.950 
 D -WSXGA+ 11680x105065.290 59.954 
 D -W XGA+ 114 40x90055.935 59.887 
D -720p1280x72045.000 60.000 
D -720p1280x72037.500 50.000 
D -1035i1920x1035 i33.750 60.000 
D -1080i1920x1080 i33.750 60.000 
1920x1080 i28.125 50.000 
D -1080psf/ 301920x108033.750 60.000 
D -1080psf/ 251920x108028.125 50.000 
D -1080psf/ 241920x108027.000 48.000 
D -1080p
1920x108033.750 30.000 
1920x108028.125 25.000 
1920x108027.000 24.000 
1920x108067.500 60.000 
1920x108056.250 50.000 
✔Note:
• Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
• Specifications are subject to change without notice.
•   
You might be able to project images even when signals other than above are inputted, however the functions of the 
projector could be limited.
•   Depending on your PC settings, the digital signals of your PC may not be projected correctly. In such a case, confirm 
your PC settings.
•   
When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. 
Be sure to follow this procedure, other wise an image may not be projected on the screen. If an image is not projected 
correctly, restart your PC.
•   Do not disconnect the cable while the projector is running. If the cable has been disconnected and then reconnected, 
an image may not be correctly projected.
h
hD-480i and D-575i signals are acceptable only when transferred via an HDMI cable.
h 
						

							
90

When using the optional board (DVI) “POA-AMDADI”, refer to the chart on the previous page.
When using other optional boards, refer to the charts below.
Supported Signal Format for Optional Board
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
D-480i720x48015.73460.000
D-575i720x57615.62550.000
D-480p720x48031.47060.000
D-575p720x57531.25050.000
D-1035i1920x1035 i33.750 60.000 
D-1080i1920x1080 i33.75060.000 
1920x1080 i28.125 50.000 
D-720p/501280x72037.50050.000
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
D-720p/601280x72045.00060.000
D-1080psf/241920x108027.000 48.000 
D-1080psf/251920x108028.125 50.000 
D-1080psf/301920x108033.750 60.000 
D-1080p
1920x108027.00024.000
1920x108028.12525.000
1920x108033.75030.000
Dual SDI Board “POA-AMD17SDID”
Dual Link SDI Board “ POA-AMDSDIDL”
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
480i720x48015.73460.000
575i720x57615.62550.000
480p720x48031.47059.880
575p720x57531.25050.000
1035i1920x103533.75060.000
1080i/601920x108033.75060.000
1080i/501920x108028.12550.000
 720p/501280x72037.50050.000
720p/601280x72045.00060.000
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
1080psf/241920x108027.000 48.000 
1080psf/251920x108028.125 50.000 
1080psf/301920x108033.750 60.000 
1080p/241920x108027.000 24.000
1080p/251920x108028.12525.000
1080p/301920x108033.75030.000
1080p/501920x108056.25050.000
1080p/601920x108067.50060.000
5 BNC, S Board “ POA-AMD5VD”
Appendix
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
D-480i720x48015.73460.000
D-575i720x57615.62550.000
D-480p720x48031.47060.000
D-575p720x57531.25050.000
D-1035i1920x1035 i33.750 60.000 
D-1080i1920x1080 i33.750 60.000 
1920x1080 i28.125 50.000 
 D-720p/501280x72037.50050.000
 D-720p/601280x72045.00060.000
D-1080psf/241920x108027.000 48.000 
D-1080psf/251920x108028.125 50.000 
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq.(kHz)V-Freq.(Hz)
D-1080psf/301920x108033.750 60.000 
D-1080p
1920x108027.00024.000
1920x108028.12525.000
1920x108033.75030.000
D-1080p/501920x108056.25050.000
D-1080p/601920x108067.50060.000
D-2K/24psf2048x108027.00048.000
D-2K/25psf2048x108028.12550.000
D-2K/30psf2048x108033.75060.000
D-2K/24p2048x108027.00024.000