Sanyo Plc Hf10000l Projector User Manual

							
51

Video Input
✔Note:
• When no signal is detected, Normal is set 
automatically and the Aspect dialog box disappears.
• The adjustable range for Scale H/V and Position H/V 
are limited depending on the input signal.
•  Natural wide cannot be selected when 720p, 1035i, 
1080i or 1080p is selected on AV System Menu (p.46).
1

Press the MENU button to display the on-screen 
Menu. Use the Point ed buttons to select Screen and 
then press the Point 8 or the SELECT button
Use the Point  ed buttons to select the desired item 
and then press the SELECT button.
Provides the image within a screen size keeping its original 
aspect ratio.
Provides the image at the 16:9 wide screen ratio.
Screen Size Adjustment
Scales the image proportionally to fit the entire screen. Either side of image may go over the screen.
Provides the image to fit full screen size.
Expands the right and left side of images naturally without 
changing the center areas.
Provides the last stored aspect screen image. 
Adjusts the screen scale and position manually with this 
function.
Press the Point 8 button at Custom adj. and the Custom 
adjustment menu is displayed on the screen, you can use the 
Point ed buttons to choose the item you want to adjust.
 Scale H/V  ...........  Adjusts the Horizontal/Vertical screen 
scale.
  H&V  ...................  When set to On, the aspect ratio is 
fixed. Scale V appears dimmed and 
becomes unavailable. Adjust Scale H, 
then the screen scale is automatically 
modified based on the aspect ratio. 
  Position H/V.......  .  Adjust
s the Horizontal/Vertical screen 
position.
  Common  ............  Save
s the adjusted scale or position to 
all the inputs. Press the SELECT button 
at Common to display a confirmation 
box. To save the scale or position, press 
the SELECT button at "Yes", When 
Custom is selected, the saved scale or 
position is used.
  Reset  .................  Reset
s the all adjusted values. Press 
the SELECT button at Reset to display 
a confirmation box. To reset, press the 
SELECT button at Yes.
Normal
Full
Wide (16:9)
Zoom
Natural wide
Custom
Custom adj. 
						

							
5

Video Input
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at “Yes.”
Ceiling 
Rear 
When this function is set to On, the picture will be top/
bottom and left/right reversed. This function is used to 
project the image from a ceiling-mounted projector.
When this function is set to On, the picture will be left/right 
reversed. This function is used to project the image from 
rear of the screen.
This function is used to adjust keystone distortion of the  
projected image. Use the Point ed buttons to choose the 
item you want to adjust.
Adjusts the Horizontal/Vertical keystone distortion of the  
projected image.
Standard 
 Corner correction
Adjusts the corner distortion of the projected image.
Corner pattern
Choose a Corner pattern mode among Red, White, Blue, 
and Off.  
 Store
This function is used to scale the input source to fit the 
screen. Select one of the following aspect ratio which is 
suitable for your cable and computer. Select “Full” if you do 
not want to set aspect ratio.
Full .......Flexible aspect ratio
16:9  ......16:9 aspect ratio
16:10  ....16:10 aspect ratio
4:3  .......4:3 aspect ratio✔Note:
• Natural wide cannot be selected when 720p, 1035i, 
1080i or 1080p is selected on AV System Menu (p.46).
• When the 16:9 function is selected, Wide(16:9) is not 
available in the PC and AV screen (pp.43, 51).
• When the 4:3 function is selected, Natural wide is not 
available in the AV screen (p.51). 
    Store  ......Keeps the keystone correction even when the AC 
                     power cord is unplugged.
    
Reset  .....Releases the keystone correction when the AC
                     power cord is unplugged.
Press the KEYSTONE button on the remote control to switch 
the Standard (for Vertical/Horizontal) /Corner correction 
adjustment. The Standard or Corner correction adjustment 
dialog box appears. Use the Point  ed 7 8 buttons to correct 
the Standard or Corner distortion.  (p.31) 
Keystone
Ceiling
Rear
Screen aspect
Reset 
						

							
5

Settings
Press the MENU button to display the On-Screen 
Menu.  Press the Point ed buttons to select Setting 
and press the Point 8 or the SELECT button to access 
the submenu items.
1
Use the Point ed buttons to select the desired item 
and then press the Point 8 or the SELECT button to 
access the selected item.
This projector has a Setting menu that allows you to set up 
the other various functions described below.
Use the Point ed buttons to select the desired item 
and then press the SELECT button.
The language used in the On-Screen Menu is available in English, 
German, French, Italian, Spanish, Portuguese, Dutch, Swedish, 
Russian, Chinese, Korean and Japanese.
Language
Settings
This function decides whether to display On-Screen Displays.
 On ........................  Shows all the On-Screen displays. Use this 
function when you want to project images 
after the lamp becomes bright enough. The 
factory default setting is in this option.
 Countdown Off  ..... Shows the input image instead of the 
countdown when turning on the projector. 
Use this function when you want to project 
the image as early as possible even when the 
lamp is not bright enough.
 Off  ........................  Hides the On-Screen Displays, but there are 
exceptions: 
• On-Screen Menu
• The "Power off?” message (p.25)
•   
Time counter displayed when the Power 
Management and/or P-Timer function works
• Orange arrows for repositioning a menu .
•   
The ”Please wait ...” message (except for the filter 
warning message)
•   
Warning messages displayed when configuring 
Video delay control settings and pressing a button 
unavailable in Picture in Picture mode.
•   In Picture in/by Picture mode, warning frame (red) 
displayed when using the unavailable combination 
of Input buttons on the remote control or inputting 
unacceptable signals. 
• White Arrows in panning mode (p.43)
• Corner patterns (p31) 
This function is used to adjust the On-Screen Menu display 
position. Press the SELECT button and the adjustment screen 
appears (arrows appear). Use the Point ed7 8 buttons to adjust 
the position. After making the adjustment, press the SELECT 
button to return to the Menu screen. To resize the menu, select 
Normal (for normal size) or Double (for double size). Even after 
selecting Double, the Startup Logo size doesn’t change.
Menu
Language
Menu
Display 
						

							
54

Settings
Select the background color or image when no input signal 
is detected. Press the Point ed buttons to switch between 
each option.
 Blue ...................  Projects a blue background.
 User  ...................  Projects a captured image.
 Black  ..................  Projects a black background.
Allows you to select a lamp mode.
2-Lamps  ................Uses two lamps. 
1-Lamp  ..................Uses one lamp.
Auto: Automatically and preferentially 
uses a lamp with shorter cumulated 
lighting time.
Constant mode  .....Automatically switches between 
2-Lamps mode and 1-Lamp mode, 
or performs digital processings like 
modulation of the light from the lamp(s) 
to keep the target brightness by 
switching the lamp modes. 
Target: Allows you to specify the desired 
target brightness (up to 1024). Follow 
these steps below:  1) Select Target 
and press the SELECT button. 2) Set 
Target brightness by using the Point ed 
buttons and press the SELECT button. 3) 
Select Yes in the confirmation dialog box 
to activate Constant mode.
Current: Displays current brightness. If 
luminance level of lamp does not reach 
the target brightness, the parameter is 
displayed in red.
This function allows you to change among the lamp 
modes: Auto, Normal, Eco 1, and Eco 2 
Lamp control
Auto  . . . . Brightness according to the input signal. 
Normal  . .  Normal brightness. 
Eco 1. . . .   Lowers brightness and decrease of fan 
speed. Lower brightness reduces the 
lamp power consumption and extends 
the lamp life.
Eco 2. . . .   Lowers brightness and increase of fan 
speed. Lower brightness reduces the 
lamp power consumption and extends 
the lamp life. It is recommended to 
use Eco 2 when using the projector 
continuously over a long period of time. 
The fan noise becomes louder in Eco 2 
than in Eco 1. Select the suitable mode 
for the used environment. 
✔Note
The fan noise becomes louder in Eco 2 than in Eco 1.  
Select the suitable mode for the used environment.
✔Note
• In Constant mode, some Setting menu items are not 
available.
• You can use the Real Color Manager Pro CD-ROM 
(supplied) except in Constant mode. 
• In this example, the Target value is specified to 820, but 
as it is not absolute luminance, you can specify a value 
in the 0 - 1024 range.
Background
Lamp mode
Lamp control 
						

							
55

Select the lamp operation when the total lighting time of a lamp 
exceeds the recommended total hours of use.
  Mode 1 ............  A lamp can be turned on even after 
exceeding the recommended total hours of 
use.
  Mode 2  ............  A lamp can be turned on even after 
exceeding the recommended total hours of 
use. But the projector turns off automatically 
after 3 minutes.
Lamp life control
✔Note
• Lamp mode cannot be changed for a while after turning on the 
projector. Lamp needs some time to stabilize after the power 
is turned on. Stored lamp mode will be active after the lamp is 
stabilized.
• If Mode 2 has been selected and the projection lamp exceeds the 
recommended total hours of use, the replacement icon will be 
displayed at the time of power-on. Then the projector will turn off 
after 3 minutes.
In 1-lamp mode, this function allows you to specify the timing of 
switching between the lamps.
 Off  .....................Turns off the lamp switching function
 XXXXH..............When the cumulated lighting time of the lamp 
reaches the specified time, automatically uses 
the other lamp. (Options: 24H, 200H, 500H, 
1000H, 2000H)
✔Note
The projector cannot switch between the lamps at exactly the same 
time as you specified. The time specified here is approximate. 
 
Shows the selected mode (Off/User 1-5) and its status (Stored 
/Free/ Adj.). User 1 and User 2 have stored default values. See 
page 30 for details.
  Picture in Picture
This function is used to project two images simultaneously by 
placing a separate small sub screen within or next to the main 
screen.
Use the Point ed buttons to select Picture in Picture and then 
press the SELECT button to display a dialog box. You can also 
display the dialog box by pressing and holding the PIP button on 
the remote control for more than 3 seconds.
( In P in P, the larger picture is main picture, and the smaller one is 
sub picture; in P by P, the left picture is main picture, and the right 
one is sub picture.)
Settings
Lamp interval
Picture in Picture 
						

							
56

Settings
P in P: Provide the images of Main picture and Sub picture 
at the ratio of Screen aspect in the Screen Menu. 
P by P: Provide the images of Main picture and Sub picture at the ratio of 4:3.
  Mode
  Main picture / Sub picture
Input .....Select an input from Input 1-4. Source  ..  
Select an input source. The display varies depending on the selected input.Size  .......  
Select the display size. Main picture can be changed   between 10 and 100%, and Sub picture can be changed between 10 to 50% in increments of 10%.  When P by P is selected in Mode, the projection size is fixed to 50%.Position  .  
Press the SELECT button at Position and the display position setting screen appears.
Use the Point ed 7 8 buttons to adjust the display position of active frame indicated in white. The frame will disappear after 10 seconds or when the SELECT button is pressed.
Selecting the Main picture or Sub picture
During Picture in Picture mode, and being undisplayed On 
Screen Menu, press the SELECT button to select Main or 
Sub picture. (A red frame will be displayed on the selected 
picture.)
Switching Input and Source 
When selecting Main picture or Sub picture, input and source 
can be set by pressing the INPUT button on the side control 
or INPUT 1/2/3/4 button on the remote control. Operation on 
the On Screen Menu is not necessary.
Selected Mode
Status (Stored /Free/ Adj.) of the selected mode
Display position setting screen
Active frame
(White)
Center line
display
✔Note
• The Picture in Picture function is not available 
depending on the input signals and the selected 
input terminals. Refer to List of Picture in Picture 
for details. (p.96)
• When the input signal(s) is/are incompatible, X 
mark will be displayed on the Main/Sub picture.
✔Note
• P by P is not available when the 4:3 function is 
selected in Screen aspect (p.45, 52).
• When P by P is selected in every User 1-5 and 
the 4:3 function is selected in Screen aspect, PIP 
button on the remote control is not available. To 
set Picture in Picture, select Full, 16:10, or 16:9 in 
Screen aspect (p.45, 52).
Set the Frame Lock to Main picture or Sub picture.
  Frame lock
Press the SELECT button at Reset to display a confirmation 
box. To reset, press the SELECT button at Yes.
  Reset
  Mode free
  Store
Delete the data stored in the Mode and return to Free. Use 
the Point ed buttons to select Mode free and press the 
SELECT button to show the Where to free? dialog box. 
Move the highlight to one of the mode (User1 - 5) which 
you want to delete and press the SELECT button. Then the 
confirmation box appears. To delete, select Yes. 
Store the adjusted data in the User 1-5. Use the Point ed 
buttons to select Store and press the SELECT button to 
show the Where to store? dialog box. Move the highlight 
to one of the mode (User1 - 5) which you want to store 
and press the SELECT button. Then the confirmation box 
appears. To store adjusted data, select Yes. 
Returns to the Picture in Picture menu. 
  Back 
						

							
57

Status (Stored /Free/ Adj.) of the selected mode
Settings
This function allows multiple projector images to be seamlessly 
overlapped.
When displaying multiple screens, eliminates the difference in 
color between the images that are projected from the projectors.
Use the Point ed buttons to select Edge blending and then 
press the SELECT button to display a dialog box. Use the Point 
ed7 8 buttons to adjust the setting value.
On/Off . . . . . . . . 
Set to On to activate the Edge blending 
function.
Start . . . . . . . . . . The point at which edge blending starts. 
The edges of a green frame around an 
image shift in accordance with the values 
specified here. Specify a value in the 0 
- 1024 range for Left and Right and a value 
in the 0 - 540 for Top and Bottom.
Width . . . . . . . . .  
Adjusts the width of correction. 
Right/Left: Set the width. (from 0 to 1024). 
Top/Bottom: Set the width. (from 0 to 540).
Black level . . . . . 
Adjusts the black level of projected image. 
All:      
The values of R, G, and B will be 
changed simultaneously.
  R/G/B:    
Adjusts the value (up to ± 127).
Test pattern . . . . 
Select On to display a suitable pattern 
(white: 50%).
Menu off . . . . . .  
Closes the menu and hides all edge lines 
(in green, red, and gray) temporarily.
Reset . . . . . . . . .  
Select Reset and press the SELECT 
button. Then Return to factory default of 
Edge Blending? message appears . To 
reset, press the SELECT button at [Yes].
Back . . . . . . . . . . Hides the Edge blending setting menu and 
returns to the Setting menu.
✔Note:
•  
The  overlapping  areas  might  become  uneven  depending 
on  the  images.  In  such  a  case,  it  is  recommended  to 
decrease  the  contrast  of  the  images  in  the  Image  Adjust 
Menu.
•  
See “How to adjust multiple screens” on pages 69, 70 for 
further information.
When multiple sets are used simultaneously, this projector 
allows the user to correct the difference of colors among the sets.
Use the Point ed buttons to select Color matching and then 
press the SELECT button to display a dialog box. Use the Point 
ed7 8 buttons to adjust the setting value.
Color matching. . . . . .  
Set to ‘On‘ to activate the Color matching 
function. When the color matching is 
set to Off, all items except for Advanced 
color matching and Back are displayed in 
grayout and cannot be adjusted.
Color adjustment . . . . 
Adjusts the color setting of Red/Green/
Blue/White. The chromatic coordinate 
(X,Y) of Red, Green, Blue, and White can 
be adjusted respectively. The adjustable 
range is from 0.000 to 1.000.
Auto test pattern . . . .  
Select On to display a suitable pattern 
when setting items.
Color matching
Edge blending 
						

							
5

Settings
Measured Information: When selecting “Measured Information”, 
the window shown right appears. Current 
image level is shown. When “image” is 
set to “Real” or “Cinema”, the “Standard” 
item in the window is activated. To go back 
to the “Advanced color matting” window, 
press any key. 
Advanced color matching: Press the POINT ed buttons to switch 
between “On” and “Off”. Selecting On 
displays the values which link to the Color 
Match values. 
Measured:   Displays the measured values of Red, 
Green, Blue, and white. 
Target:    
Adjust
s the chromatic coordinate (X,Y) 
and the gain value (g) of Red, Green, Blue, 
Cyan, Magenta, Yellow, and White. Use 
the Point ed buttons to move the red 
frame pointer to an item of which you 
want to adjust the value and then press 
the SELECT button. Use the Point ed 
buttons to adjust the value. To move to 
the next digit, use the Point ed buttons. 
Press the SELECT button to set the value. 
Auto test pattern:     Select On to display a suitable pattern 
when setting items.
Menu off: 
Close the menu temporarily. 
Factory default:  
Select Factory default and press the 
SELECT button. Then Return to factory 
default of Color matching? message 
appears. To reset the selected Measured 
value and Target value, select Yes. Then, 
the confirmation box appears. Press the 
SELECT button at Yes again.
Reset  : 
Select Reset and press the SELECT 
button. Then the confirmation message 
appears. Press the SELECT button at Yes. 
to reset to the previously stored values.
Store  :
 Select Store and press the SELECT 
button. Then the Confirmation box 
appears. To store adjusted data, select Yes.
Test pattern: 
Displays the “Test pattern” menu.
Back:  
Cancels the “Advanced color matching” 
menu display.
Advanced 
color matching . . . . . .  
Select Advanced color matching and press 
the SELECT button for more detailed 
settings. Another setting screen will 
appear. 
Reset 
 . . . . . . . . . . . . .  
Select Reset and press the SELECT button. 
Then the confirmation message appears. 
Press the SELECT button at Yes to reset to 
the previously stored values.
Store 
 . . . . . . . . . . . . .  
Select Store and press the SELECT button 
to display the Confirmation box. To store 
adjusted data, select Yes.
Advanced color matching
Measured information
Advanced color matching
Test pattern 
						

							
59

This function allows you to customize the screen logo with 
Logo select, Capture, Logo PIN code lock and Logo PIN code 
change functions.
✔Note
When On is selected in the Logo PIN code lock function, 
Logo select, Capture and Logo PIN code change cannot be 
selected.
Logo select
This function decides on the starting-up display from among 
following options. 
User ..........Shows the image you captured. 
Default  ......Shows the factory-set logo. 
Off  .............Shows the countdown display only.
✔Note
• Before capturing an image, select Standard in the Image 
Select Menu to capture a proper image (pp.39, 47).
• The output image resolution from a computer can be 
supported up to the panel resolution (2048 x 1080).
• When capturing the image that has been adjusted by the 
Keystone function, the adjusted data is automatically reset 
and the projector captures an image without keystone 
correction. 
• When Logo PIN code lock is set to On, Capture cannot be 
selected.   
• When starting to capture a new image, the previously stored 
image is cleared even if you cancel the capturing.
• When there is no captured image or it is interrupted while 
capturing an image, User can not be selected, you can only 
switch between Default and Off.
• Capture function is not available when the Picture in Picture 
function is set to User1-5.
• When changing a PIN code, the new PIN code numbers 
don't appear as asteriskmarks. 
Capture
This function enables you to capture an image being projected 
to use it for a starting-up display or interval of presentations. 
Select Capture and press the SELECT button.  A confirmation 
box appears and select Yes to capture the projected image. After 
capturing the projected image, go to the Logo select function 
and set it to User. Then the captured image will be displayed 
the next time you turn on the projector. To cancel the capture 
function, select Yes in the "Quit?" confirmation box.
Select Normal or Enhanced according to the output signal 
of video equipment. Press the Point ed buttons to switch 
between each option.
  Normal 
. . . .  When the output of video equipment is set to 
“STANDARD.”
  Enhanced
. .  When the output of video equipment is set to 
“ENHANCED.”
Settings
✔Note:
•  The names for the output setting of video equipment vary 
from equipment to equipment. For details, refer to the 
manual of video equipment.
Logo select
Capture
Logo (Logo and Logo PIN code lock settings)
HDMI setup 
						

							
60

This function prevents an unauthorized person from 
changing the screen logo.
 Off  .............  The screen logo can be changed freely from 
the Logo Menu (p.59).
  On  .............  The screen logo cannot be changed without a 
Logo PIN code.
If you want to change the Logo PIN code lock setting, 
press the SELECT button and the Logo PIN code dialog 
box appears. Enter a Logo PIN code by following the steps 
below. The initial Logo PIN code is set to "4321" at the 
factory.
Logo PIN code lock
.  Change Logo PIN code
Logo PIN code can be changed to your desired four-digit 
number. Press the SELECT button to select Logo PIN code 
change. Current logo PIN code dialog box appears, use the 
Point edbuttons to enter the correct code. The New Logo 
PIN code input dialog box appears. Set a new Logo PIN 
code, confirmation box appears, choose Yes to set the new 
Logo PIN code.
1.  Enter a Logo PIN code
Use the Point ed buttons on the side control or Number 
buttons on the remote control unit to enter a number. 
When using side control
Use the Point ed buttons on the side control to select a 
number. Press the Point 8 button to fix the number and 
move the red frame pointer to the next box. The number 
changes to “✳.” Repeat this step to complete entering a 
four-digit number. After entering the four-digit number, move 
the pointer to “Set.” Press the SELECT button so that you 
can change the Logo PIN code lock setting.
When using remote control 
Press the Number buttons on the remote control unit to 
enter a number (p.16). When you complete entering a four-
digit number, the pointer moves to “Set.” Press the SELECT 
button so that you can change the Logo PIN code lock 
setting.
If you fixed an incorrect number, use the Point 7 button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
If you entered an incorrect PIN code, “Logo PIN code” and 
the number (✳✳✳✳) will turn red for a moment. Enter the 
correct PIN code all over again.
Use the Point ed buttons to switch On or Off, and then 
press the SELECT button to close the dialog box.
.  Change the Logo PIN code lock setting
Settings
Use the Point ed  buttons on the side control or 
Number buttons on the remote control to enter a 
number. 
To enter a Logo PIN code lock
To change the Logo PIN code lock setting, follow 
these steps:   
To change the Logo PIN code