Sanyo Plc Hf10000l Projector User Manual

							
61

Settings
You can replace the filter with this function. Press the SELECT 
button at Filter control to display a confirmation box. To replace, 
press the SELECT button at Yes and the electrically operated filter 
starts to scroll.
✔Note
• Filter replacement icon and Please wait... message appear on 
the screen when the filter is being scrolled.
• The filter cannot be rewound.
• When the filter is replaced, the total accumulated time of the 
filter use is automatically set to 0.
A confirmation box appears and then select Yes.
Choose the running speed of cooling fans from the following 
options.
 Normal  .....  Operate
s in this mode under normal conditions.
  Max
..........  Use this mode when you want to increase the 
cooling effect when operating the projector in 
high ambient temperature environment. Fan 
noise is louder than Normal. 
The eight different remote control codes (Code 1-Code 8) are 
assigned to the projector; the factory-set, initial code (Code 1) 
and the other seven codes (Code 2 to Code 8). 
The same code should be set on both the projector and the 
remote control. For example, operating the projector in Code 
7, the remote control code also must be switched to Code 7.
To change the code for the projector:
Select a remote control code in this Setting Menu.
To change the code for the remote control:
Press and hold the MENU button and a number button (1-8) 
on the remote control for more than five seconds to switch 
between the codes. See “Remote Control Codes” on page 
16.
✔Note
• When different codes are set on the projector and on the remote 
control, any operation cannot be made. In that case, switch the 
code on the remote control to fit the code on the projector.
• If the batteries are removed from the remote control for a long 
period of time, the remote control code will be reset.
Select a location of the infrared remote receiver of the 
remote control. See “Remote Control Receivers and Operating Range” on page 15 for details.
  Both  .........  Activates both the front and back receiver.
  Front  ........  Activate
s only the front receiver.
  Back  .........  Activate
s only the back receiver.
Filter control
Fan control
Remote control
RC sensor 
						

							
6

Settings
No  signal
4 : 50
Timer left before Lamp is off.
For reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not operated for a 
certain period.
Select one of the following options:
 Ready  .................  When the lamp has been fully cooled 
down, the POWER indicator changes 
to green blinking. In this condition, the 
projection lamp will be turned on if the 
input signal is reconnected or any button 
on the side control or remote control is 
pressed. 
  Shut down  .........  When the lamp has been fully cooled 
down, the power will be turned off. 
  Off  .....................
 Power management function is off. 
  Timer  .................  If the input signal is interrupted and 
no button is pressed for more than 30 
seconds, the timer display with No signal 
appears. It starts the countdown until 
the lamp is turned off. Use the Point ed 
buttons to set the Timer(1~30Min).
When this function is set to On, the projector will be 
automatically turned on just by connecting the AC power 
cord to the wall outlet.
✔Note
• Be sure to turn off the projector properly (see “Turning Off 
the Projector” on page 25). If the projector is turned off in the 
incorrect sequence, the "Direct on" function does not work 
properly.
✔Note 
• Factory default is Ready: 5 Min.
•    When the shutter is closed while the Power management 
function is working, the Power management function is 
released.
Power management
Direct on 
						

							
6

Settings
Key lock
PIN code lock
This function locks the side control and remote control 
buttons to prevent operation by unauthorized persons.
  . . . . .Unlocked.
  . . . . .Locks the operation of the side control.
To unlock, use the remote control
    . . . . .Locks the operation of the remote 
control. To unlock, use the side control.
If the side control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with your remote control, contact the dealer where 
you purchased the projector or the service center.
This function allows you to use the Key lock and PIN code 
lock function to set the security for the projector operation.
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
 Off 
. . . . .Unlocked.
  On 1 
. . . . .Enter the PIN code every time turning on 
the projector.
  On 2 
. . . . .Enter the PIN code to operate the projector 
once the power cord is disconnected; as 
long as the AC power cord is connected, 
the projector can be operated without a 
PIN code.
Whenever you change the PIN code lock setting or the 
PIN code (the four-digit number), you are required to 
enter the PIN code. The "1234" is set as the initial PIN 
code at the factory. 
If you want to change the PIN code lock setting, Press 
the SELECT button and the PIN code dialog box appears.
Security (Key lock and PIN code lock) 
						

							
64

When the projector is locked with a PIN code, the 
PIN code lock symbol appears in the Guide.
To change the PIN code lock setting
To enter a PIN code
When using side control
Use the Point ed buttons on the side control to select a number. 
Press the Point 8 button to fix the number and move the red 
frame pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit number. After 
entering the four-digit number, move the pointer to “Set.” Press 
the SELECT button so that you can change the PIN code lock 
setting.
When using remote control
Press the Number buttons on the remote control to enter a 
number (p.16). When you complete entering a four-digit number, 
the pointer moves to “Set.” Press the SELECT button so that you 
can change the PIN code lock setting.
If you fixed an incorrect number, use the Point 7 button to move 
the pointer to the number you want to correct, and then enter the 
correct number.
If you entered an incorrect PIN code, “PIN code” and the number 
(✳✳✳✳) will turn red for a moment. Enter the correct PIN code all 
over again.
The PIN code can be changed to your desired four-digit 
number. Press the Point d button to select PIN code change 
and press the SELECT button. The Current PIN code dialog 
box appears. Use the Point ed buttons or the Number 
buttons on the remote control to set the current PIN code. 
The New PIN code dialog box appears. Set a new PIN code, 
the confirmation box appears, and choose Yes to set the 
new PIN code. 
To change the PIN code
 To change PIN code 
CAUTION:
WHEN y OU HAVE CHANGED THE PIN CODE,  WRITE DOWN 
THE NEW PIN CODE IN COLUMN OF  THE PIN CODE NO. 
MEMO ON PAGE 94,  AND KEEP IT SECUREL y. IF yOU FORGET 
y OUR PIN CODE,  THE PROjECTOR CAN NO LONGER BE 
STARTED .
Settings
Use the Point ed buttons to select OFF, On 1 or On 2. 
Press the SELECT button to close the dialog box. 
						

							
65

Use the Point ed buttons to adjust the Projector ID.
Projector ID ... 1 - 999. (Factory default setting : Projector ID 1)
This feature allows users to set serial communication 
configuration (Projector ID) when several projectors are 
connected via the RS-232C terminal (serial port) of the 
projector.
Shutter function is available to block out light to the screen, 
so that the screen can be used for the other presenters.
Prohibits the shutter operation from the remote control and 
the projector's side control.
Remote control 
 . . .  Selecting "On" prohibits the shutter 
operation from the remote control.
Projector . . . . . . . .  
Selecting "On" prohibits the shutter 
operation from the side control.
It is possible to prohibit the shutter operation from both of the 
remote control and the side control.
Protection
Management
The Shutter Management function turns off the projection lamp 
when the projector is left with the shutter closed and the set 
time has passed away. The count-down time can be set between 
5 and 480 minutes. When the count-down time has elapsed, 
the shutter will be opened up automatically and the lamp will be 
turned off to cool itself down. The SHUTTER indicator is blinking 
blue during this cooling-off period. When the lamp has been fully 
cooled down, the POWER indicator turns green lighting and the 
SHUTTER indicator keeps blinking. Should the ON / STAND-BY 
button be pressed in this condition, the projection lamp will be 
turned on and the SHUTTER indicator turns off.
Effect
Choose the image effect at opening or closing the shutter from 
the following options.
 Off  .............  Disable.
  L1  ..............  The Image will fade in and out at opening or 
closing the shutter.
  L2  ..............  The Image will fade in and out more slowly 
compared with L1. 
Release key
Choose the active buttons to release the shutter when the 
shutter is closed from the following options.
  Any  ............  By pressing any buttons on the remoter control 
and the side control when the shutter is closed, 
the shutter will be released.
  SHUTTER  ..   Only the SHUTTER button on the remote control 
and the side control can be released the shutter 
when the shutter is closed. 
Only the following buttons are active when the 
shutter is closed; 
- INPUT button and INPUT 1/2/3/4 button 
- ON/STAND-BY button
Settings
Projector ID
Shutter 
						

							
66

When you want to make a digital processing of a projected 
image faster, set this function.
Use the Point ed buttons, select an item of Off/Low/Mid/
High.
Digital processing speed becomes fast by order of Low → 
Mid → High. High is the fastest.Fig.1
✔Note:
• The following functions are not available respectively when 
Video delay control is set to Low/Mid/High.
Low .....Keystone can not be selected.
Mid  ......Progressive and Noise reduction can not be selected.
High  .....  
Keystone, Progressive and Noise reduction can not be 
selected.
• When Video delay control function is set to Low or High and 
press the KEYSTONE button on the remote control, “Video delay 
:On” will be displayed on the left lower area of the screen (Fig.1).
Closed Caption is a function that displays the audio portion 
of a TV program as text on the screen. If the input signal 
contains closed captions, you can turn on the feature 
and switch the channels. Press the Point ed buttons to 
select Off, CC1, CC2, CC3 or CC4.
If the Closed caption is not clear, you can change the text 
from Color to White.
Settings
Video delay control
Closed caption 
						

							
67

Filter replacement icon appears on the screen at a set time.
✔Note: 
• Do not reset the counter when the filter or the filter cartridge is not replaced.
• Timer setting notifies that the filter needs replacement. To replace the filter, use the filter control function (p.61).
Fig.1   Filter replacement icon
Filter cartridge replacement icon appears on the screen when the filter scroll is counted down to 0 scroll.　　
Fig.4   Filter cartridge replacement icon
✔Note:
• Fig.1,  Fig.  2,  Fig.  3  and  Fig.  4  appear  at  turning  on  and  selecting input source.
• Fig.1,  Fig.  2,  Fig.  3  and  Fig.  4  will  not  appear  when  the Display  function  is  set  to  Off  (p.53)  or  during  “Freeze” (p.30).
Last scroll icon appears on the screen when the filter is down to the last scroll.
Fig.3   Last scroll icon
This function is used to set a frequency for the filter 
replacement.
Use the Point ed buttons to select Filter counter and 
then press the Point 8 or the SELECT button to access the 
submenu items. 
Filter counter  . . . 
Show the total accumulated time of the 
filter use timer setting.
Timer  . . . . . . . . .  
To set a timer, when the projector reaches 
the time, the Filter replacement icon 
(Fig.1) appears on the screen and the total 
accumulated time turns red, indicating 
that the filter replacement is necessary. If 
the filter is out of scroll and the projector 
reaches a time set in the timer setting, 
Fig.2 appears on the screen, indicating 
that the filter cartridge replacement is 
necessary.
Filter counter reset. . 
When replacing the Filter cartridge, reset 
the Filter counter and the Scroll remaining 
(p.73). 
Scrolls remaining  . . . . When the filter scroll is counted down 
to 1,Scroll remaining on the screen is 
showing 0 scroll(s) , the last scroll icon 
(Fig.3) appears on the screen. When the 
filter scrollis counted down to 0, the Filter 
cartridge replacement icon (Fig.4) appears 
on the screen and the WARNING FILTER 
indicator lights orange, indicating that the 
filter cartridge replacement is necessary.
Scroll counter reset. . 
When replacing the Filter cartridge, reset 
the Filter counter and the Scroll remaining 
(p.73).
Fig.2
Press the SELECT button to select Timer and then 
use the Point ed buttons to set the timer. Select from (Off/ 400H/ 700H/ 1000H) depending on the use environment.
Settings
Filter counter 
						

							
6

This function allows you to change the presentation of the P-
timer and execute it.
Select one of the following options:
 Count up ............  The P-timer display 000:00 appears on 
the screen and the count starts (000:00–
180:00) 
 Count down  ....... The time set in the Timer setting appears 
on the screen and the countdown starts.
 Timer  ................. Use the Point ed buttons to set the 
Timer (1–180 Min). Only set to Count 
down, Timer is active. Factory default 
value is 10 Min.
 Start  ...................  Executes the count up or count down 
function. Press the SELECT button at 
Start, Start changes to Stop in the Screen 
Menu.  At that time, press the SELECT 
button at Stop to stop Count up or Count 
down,  and Stop changes to Restart in the 
Screen Menu. Press the SELECT button 
at Restart to resume Count up or Count 
down.
 Reset  .................  Resets the P-timer values. Press the 
SELECT button at Reset to return to the 
following value;
  Count up ... "000:00"
  Count down ... Timer that you set
 Exit..................... To exit the P-timer operation.
Stop or Cancel the P-timer via Remote Control
To stop the P-timer, press the P-TIMER button.
To cancel the P-timer, press and hold the P-TIMER button for 
a few seconds.
P-TIMER
This function returns all setting values except for User 
logo, PIN code lock, Logo PIN code lock, Filter counter and 
Network setting to the factory default settings.
Various test pattern are available for use when setting up the 
projector.
Settings
P-timer
Test pattern
Factory default 
						

							
69

How to Overlap the Projection Images on a Screen 
You can obtain a seamless image by using the Edge Blending function which blends the images projected from multiple 
projectors and digitally dims the edges of the images and the Color Matching function which eliminates color unevenness. 
Follow the steps from 1 to 5 (or 8 if necessary) below to adjust multiple projector images.  
Configure the settings for screen size, image level, and lamp mode. These settings must match those for the rest 
of the projectors. Select Constant mode from the Lamp mode menu and then specify the same Target value as the 
projectors. 
1
4Adjust the position, focus and zoom of each image if necessary, and then overlap the shaded areas by using the lens 
shift function. When the shaded areas are overlapped with each other correctly, the red lines turn yellow.
Edge blending 
Display the images to be edge-blended on a screen. 
(In the following example, two projectors: Projectors A and B are used.)
If black horizontal and/or vertical bar(s) on four sides of the images appear, adjust the Start values until they become 
invisible and specify the values for Width to adjust the width of the area where the images overlap. (Refer to pages 57, 
58 for operation procedure.)
2
3
•  
The blending widths for each projector (e.g., the Right width of Image A and the Left width of Image B) must be set 
to the same value.
•   
The values in the figures are example .
•   
The 
frame around an image is displayed in green, and red line(s) appear at the specified position(s). 
•   
T
he areas to be overlapped are displayed in shaded color.
Projector AProjector B
Image A
Image B
Screen
Image A
Image BRed line
Yellow lines
Red line
Green frame
Green frame
How To Overlap the Projection Images
Change the Right width to 100.
Change the Left width to 100.
Set to On.
Green frame 
						

							
70

✔Note:
•  
The  overlapping  area  might  become  uneven  depending  on  the  images.  In  such  a  case,  it  is  recommended  to 
decrease the contrast of the images in the Image Adjust Menu.
If the colors of the left and right images do not match, then follow the next step.
Select Color matching in the setting menu and display the Color matching dialog box.
Then, set Color matching to On and adjust the color settings (Red/Green/Blue/White). 
(Refer to pages 57, 58 for operation procedure.)
6
Color matching
✔Note:
•   
When you change the values of Target, make sure that each 
Target  value  should  be  within  the  range  of  Measured  value. 
(e.g.,  In  the  case  of  the  Fig.1,  the  X  value  of Target-Red 
should  be  within  0.674  which  is  the  X  value  of  Measured-
Red.)
Fig.1
5Set Test pattern to On to display a 50 % white image. The overlap area will be brighter than the non-overlapping area. 
Adjust the Black level in the Edge blending dialog box to increase the brightness of the non-overlapping area so that 
the unevenness is reduced.
Select Advanced color matching if you need further adjustment.
In the Advanced color matching dialog box, set Advanced color matching to On and adjust the values of Target (Red/Green/ 
Blue/ Cyan/ Magenta/ Yellow/ White). 
7
If the colors of the left and right images do not match, even 
if the Target values are adjusted, use a colorimeter which 
is capable of measuring the chromaticity coordinates and 
luminance. Follow the steps below.
1.   Set Auto test pattern to On in the Advanced color 
matching dialog box.
2.   Put the cursor in the Mesured-White and press the 
SELECT button to display a white pattern.
3. 
 Measure the chromaticity coordinates (x,y) and 
luminance (lx) by using the colorimeter.
4.   Enter the obtained (x,y) values in the Mesured-White. 
(The (L) value of Mesured-White should be left at 1.000.) 
5.   Put the cursor in the Mesured-Red and press the SELECT 
button to display a red pattern.
6.   Measure the chromaticity coordinates (x,y) and 
luminance (Lx) by using the colorimeter.
7.   Enter the obtained (x,y) values in the Mesured-Red. Then, 
calculate the (L) value of Mesured-Red by applying the 
following formula and enter the value.
  (L) value of Mesured-Red = [Lx of Red] ÷ [Lx of White]
8.   Enter the values of Mesured-Green, Mesured-Blue, and 
Mesured-Half white in the same way as Mesured-Red.
9.   Adjust the values of Target again.
10.  Select Store to complete. (Apply the same adjustment to 
the other projector if necessary.)
8
How to Overlap the Projection Images
Set to On.