Sanyo Plc Ef12n Projector User Manual

31
BEFORE OPERATION
MENU BAR
SYSTEM MENU
Used to select a
computer
system.
(Refer to P36)
IMAGE MENU
Used to adjust the
computer image. 
[Fine sync / Total dots /
White Balance / Contrast
/ Brightness / Sharpness]
(Refer to P40)
PC ADJUST MENU
Used to adjust the
parameters to
match with the input
signal format.
(Refer to P38, 39)
SETTING MENU
Used to set the Display
Menu and reset Lamp
Replacement Monitor
Timer. 
(Refer to P48, 49)MODE MENU
Used to select
the Computer
input mode.
(Refer to P36)
POSITION...

32
Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc.) using the appropriate
terminals on the side of the projector (See CONNECTING THE PROJECTOR section on pages 13-22).
Connect the projectors AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the side of the
projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light GREEN.
Press the POWER ON/OFF button on the remote control unit or on the...

The normal picture image level is factory preset on the projector and can be
restored anytime by pressing the NORMAL button on the projector or on the
remote control unit. The Normal display will be displayed on the screen for a
few seconds.Press the D. ZOOM button on the wireless remote control unit. The D.zoom
and the magnifying-glass icon is displayed to indicate Digital zoom mode. Digital
zoom mode can be adjust the image size or pan the image.
To expand the image size, press SELECT (REAR CLICK)...

Press the FREEZE/NO SHOW button (on the remote control unit) is twice. The
screen will change into black image and the No show is displayed on the screen
for a few seconds.
This function is cancelled when the FREEZE/NO SHOW button is pressed again
or any other function button is pressed.
34
BASIC OPERATION
NO SHOW FUNCTION
P-TIMER FUNCTION
FREEZE PICTURE FUNCTION
AUTO IMAGE ADJUSTMENT
CURSOR FUNCTION
Press the FREEZE/NO SHOW button on the remote control unit, and the picture will remain on-screen. This...

35
Sound Volume Adjustment
Press the VOLUME (+/–) button(s) on the Top Control or on the
Remote Control Unit to adjust the volume.  The Volume dialog box
appears on the screen for a few seconds.
(+) button to increase the volume, and (–) button  decreasing.
Sound Mute Setting
Press the MUTE button on the Remote Control Unit to cut off the
sound.  To restore the sound to its previous level, press the MUTE
button again or press Volume (+/–) button(s).
Indicates the roughly level
of the volume.
Press the...

36
COMPUTER button
SELECTING COMPUTER MODE
MENU OPERATION
When selecting the Computer Mode, the Current Mode display
appears to show the information of the computer being selected.  
CURRENT MODE DISPLAY
Computer 1
Computer 2
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of
computers based on VGA, SVGA, XGA, SXGA or UXGA (refer
to “COMPATIBLE COMPUTER SPECIFICATION” on page 37).
When selecting Computer, this projector automatically tunes...

37
COMPUTER MODE
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
Specifications are subject to change without notice.
NOTE:Basically this projector can accept the signal from all computers with the above mentioned V, H-Frequency and
less than 220 MHz of Dot Clock.
COMPATIBLE COMPUTER SPECIFICATIONS
SXGA1
SXGA2
SXGA3
SXGA4
SXGA5
SXGA6
SXGA7
SXGA8
SXGA9
SXGA10
SXGA11
SXGA12
SXGA13
SXGA14
SXGA15
SXGA16
SXGA17
SXGA18
SXGA19
SXGA20
MAC21
MAC
MAC
UXGA1
UXGA2
UXGA3
UXGA4
RGB
RGB
HDTV720p
HDTV1035i...

38
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be tuned by the Multi-Scan system of this projector.  If this happens, the projector cannot reproduce a proper
image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered
picture or a skewed picture.
This...

39
The number of the total vertical lines.  Adjust the number to match
the image of your personal computer.
Total lines
Recalls the parameter data that was previously
adjusted.Reset
Stores the parameters in the memory.Stored
Clears the parameter data previously set.Mode free
Closes the PC ADJUST Menu.Quit
The number of the total dots in one horizontal period.  Adjust the
number to match the image of your computer.
Total dots
Adjustment of the horizontal or vertical picture position.  When the
image is...

40
COMPUTER MODE
Press the MENU button and the ON-SCREEN MENU will
appear.  Press the POINT LEFT/RIGHT buttons to select IMAGE
and press the SELECT (REAR CLICK) button.  Another dialog
box PICTURE IMAGE ADJUSTMENT Menu will appear. 1
2
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 127.)  
The number of the total dots in one horizontal period.  Adjust the
number to match your PC image.
Point to to decrease contrast, and select to increase contrast.
(From 0 to 63.)...