Sanyo Pdg Dsu21n Projector User Manual

                                                                                                                                  EN-29
Specifications
Remote Control
Display Type Single 0.55 DLP® chip, 5-segment color wheel
Resolution (Pixels) SVGA (800 × 600)
Lens Manual Zoom (1.1x)
Screen Size 30” – 300”
Lamp 180W
Input Source D-Sub 15 pin, S-video, composite video, USB
AUDIO IN (stereo phone jack), RS-232C
Video Compatibility NTSC3.58, NTSC4.43
PAL-60, M, N
SECAM
HDTV (480i/p, 576i/p, 720p, 1080i)...

   EN-30
Appendix
LED Indicator Messages
LED TypeColorStatusMeaning
LAMP LED
TEMP LEDGreen
OffFlash
-The projector is in standby mode.
LAMP LED
TEMP LEDGreen
GreenSolid
FlashThe projector system has some problems with its
fan, so the projector cannot start up.
LAMP LED
TEMP LEDGreen
GreenSolid
SolidThe lamp is in good condition and is projecting at
maximum brightness.
LAMP LED
TEMP LEDAmber
GreenSolid
SolidThe lamp has reached its end of life and must be
changed soon. The lamp will continue to operate...

                                                                                                                                  EN-31
Compatibility Modes
Computer: 
Video: 
 
CompatibilityResolutionH-Sync [KHz]V-Sy nc  [Hz]
VGA 640 x 480 31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
SVGA 800 x 600 35.2 56.3
37.9 60.3
48.1 72.2
46.9 75.0
53.7 85.1
XGA 1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
SXGA 1152 x 864 64.0 70.0
67.5 75.0
1280 x 960 60.0 60.0
75.0 75.0
1280 x 1024 64.0 60.0
WXGA 1280 x 768 47.8...

   EN-32
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector forrepairs. If the
problem persists, contact your local reseller or service center. Please refer to LED Indicator
Messages as well.
Start-up problems
If no lights turn on:
„Be sure that the power cord is securely connected to the projector and the other end is
plugged into an outlet with power.
„Press the ON / STAND-BY button again.
„Unplug the power cord and wait for a short while, then plug it in and...

                                                                                                                                  EN-33
Serial Control Interface
This projector provides a function to control the projectors operations by using the RS-232C
serial port.
Connection and Operation
1. Connect a RS-232C serial cross cable to RS-232C 
PORT on the projector and serial port on the PC.
2. Launch a communication software provided with PC 
and setup the communication condition as follows:
3. Send the...

   EN-34
Configuration of RS-232C Terminal
                 Mini DIN 6 pin
POINTER function
1. Connect the projector and PC with USB cable.
2. Press POINTER button on the remote control, and its flow follows as below:
1GND
2GND
3RX1
4CTS
5TX1
6RTS
IconAvailable button 
on the remote 
controlFunctions
PAGE UP/DOWN Scroll pages
ENTER Left click button
Directional buttons Move cursor
ESC Right click button
PAGE UP/DOWN Scroll pages
ENTER Enter button
Directional buttons the same as Keyboard directional...

Printed in ChinaPart No. 1AA6P1P5587-- (KA7AA)SANYO Electric Co., Ltd.