Sanyo Pdg Dsu21n Projector User Manual

							                                                                                                                                  EN-29
Specifications
Remote Control
Display Type Single 0.55 DLP® chip, 5-segment color wheel
Resolution (Pixels) SVGA (800 × 600)
Lens Manual Zoom (1.1x)
Screen Size 30” – 300”
Lamp 180W
Input Source D-Sub 15 pin, S-video, composite video, USB
AUDIO IN (stereo phone jack), RS-232C
Video Compatibility NTSC3.58, NTSC4.43
PAL-60, M, N
SECAM
HDTV (480i/p, 576i/p, 720p, 1080i)
Scanning Frequency
Horizontal Freq.
Vertical Freq.31 - 79 KHz
50 - 85 Hz
Integrated Speaker   2W x 1
Environment Operating:
Temperature: 5°C to 35°C
Humidity: 30%-85%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power Requirement AC 100 - 240 V, 50 - 60 Hz
Power Consumption 230 W
Dimension 271 x 218 x 85 mm
Weight 2.5 kg (5.5lb)
Note: Design and Specifications are subject to change without prior notice.
Battery Lithium battery (CR2025)
Operating Range ±15º/7m
Dimensions 86.5 x 54 x 8.3mm
Net Weight 26.2g (without batteries) 
						

							   EN-30
Appendix
LED Indicator Messages
LED TypeColorStatusMeaning
LAMP LED
TEMP LEDGreen
OffFlash
-The projector is in standby mode.
LAMP LED
TEMP LEDGreen
GreenSolid
FlashThe projector system has some problems with its
fan, so the projector cannot start up.
LAMP LED
TEMP LEDGreen
GreenSolid
SolidThe lamp is in good condition and is projecting at
maximum brightness.
LAMP LED
TEMP LEDAmber
GreenSolid
SolidThe lamp has reached its end of life and must be
changed soon. The lamp will continue to operate
until it fails. Change the lamp. If the lamp is off,
then the ballast will become malfunction.
LAMP LED
TEMP LEDAmber
AmberSolid
SolidThe projector is shutting and the fan motor is
cooling the lamp for shutdown. Do not unplug the
power cord or turn the power off before the Lamp
LED changes to flashing. The fan motor will turn
off when the lamp has been cooled.
LAMP LED
TEMP LEDGreen
RedSolid
FlashTemperature is too high. The lamp will turn off.
The fan motor is cooling the lamp.
LAMP LED
TEMP LEDAmber
OffSolid
-The lamp ignition failed. If temperature is too high,
the fans will cool the lamp. 
Optional Parts
The parts listed below are optionally available. When ordering those parts, give the item name
and Model No. to the sales dealer.
QCOMPONENT-VGA Cable:POA-CA-COMPVGA
QSoft Carrying Case:POA-CAC-VCL2
QRS232C cable  :  POA-MCSRL02 
						

							                                                                                                                                  EN-31
Compatibility Modes
Computer: 
Video: 
 
CompatibilityResolutionH-Sync [KHz]V-Sy nc  [Hz]
VGA 640 x 480 31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
SVGA 800 x 600 35.2 56.3
37.9 60.3
48.1 72.2
46.9 75.0
53.7 85.1
XGA 1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
SXGA 1152 x 864 64.0 70.0
67.5 75.0
1280 x 960 60.0 60.0
75.0 75.0
1280 x 1024 64.0 60.0
WXGA 1280 x 768 47.8 60.0
60.3 74.9
68.6 84.8
1280 x 800 49.7 59.8
62.8 74.9
SignalHorizontal Frequency (kHz)Vertical Frequency (Hz)
480i 15.8 kHz 60 Hz
480p 31.5 kHz 60 Hz
576i 15.6 kHz 50 Hz
576p 31.3 kHz 50 Hz
720p 45.0 kHz 60 Hz
720p 37.5 kHz 50 Hz
1080i 33.8 kHz 60 Hz
1080i 28.1 kHz 50 Hz 
						

							   EN-32
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector forrepairs. If the
problem persists, contact your local reseller or service center. Please refer to LED Indicator
Messages as well.
Start-up problems
If no lights turn on:
„Be sure that the power cord is securely connected to the projector and the other end is
plugged into an outlet with power.
„Press the ON / STAND-BY button again.
„Unplug the power cord and wait for a short while, then plug it in and press the power button
again.
Image problems
If the searching source is displayed:
„Press the INPUT button one or more times to select another active input source.
„Be sure the external source is turned on and connected.
„For a computer connection, ensure your notebook computer’s external video port is turned
on. Refer to the computer manual.
If the image is out of focus:
„Be sure the lens cap is open.
„While displaying the on-screen menu, adjust the focus ring. (The image size should not
change; if it does, you are adjusting the zoom, not the focus.)
„Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
„Press the AUTO PC button.
„Press the MENU button, go to Computer Image and adjust Total dots or Fine sync.
If no image appears on screen:
„Turn the projector on.
„Check that all connections are setup correctly.
„Check that all connected devices are functioning properly.
„Remove the lens cap and turn the projector on.
Remote control problemsIf the remote control does not operate:
„Be sure nothing is blocking the remote control receiver on the front or back of the projector.
Use the remote control within the effective range.
„Aim the remote control at the screen or at the front or back of the projector.
„Move the remote control so it is more directly in front of or behind the projector and not as far
to the side.
„The battery could be weak. Replace with a new battery. 
						

							                                                                                                                                  EN-33
Serial Control Interface
This projector provides a function to control the projectors operations by using the RS-232C
serial port.
Connection and Operation
1. Connect a RS-232C serial cross cable to RS-232C 
PORT on the projector and serial port on the PC.
2. Launch a communication software provided with PC 
and setup the communication condition as follows:
3. Send the command strings by the HEX key (HEX 
is in the range of 0-9 and a-f) for controlling the projector.
Command Format
The command is sent from PC to the projector with the format as below table.
The projector decodes the command and returns the confirmation ACK = 06.
The below table shows the typical command lists for controlling the projector. Please consult
your local dealer for further information of another commands.
Command
Power ON
Power OFF
Menu
UP
Left
Right
Input
Auto PC Adj.
Mute
Keystone UP
Keystone DOWN
Volume UP
Volume DOWN
NO Show
Freeze
Aspect
Select Computer (Analog)
Select Component
Select S-Video
Select Video
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BE
BEEF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF10
03
02
02
02
02
02
02
02
02
03
03
02
02
02
02
03
03
03
03
0305
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
19
19
19
1900
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00C6
DC
E9
6D
0B
DA
38
57
86
0E
10
23
F1
20
DF
CB
0D
19
89
E8
78FF
DB
D3
D2
D2
D3
D2
D0
D1
DE
D8
DB
DE
DF
DF
DC
DA
29
E8
69
A811
69
30
34
32
33
31
2E
2F
67
65
66
68
69
66
72
68
01
01
01
0111
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
47
47
47
4701
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
02
02
02
0200
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
CC
CC
CC
CC01
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
CC
CC
CC
CC00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
Command Strings (HEX)
Baud rate : 19200 bps
Parity check  : none
Stop bit  : 1
Flow control : none
Data bit : 8 
						

							   EN-34
Configuration of RS-232C Terminal
                 Mini DIN 6 pin
POINTER function
1. Connect the projector and PC with USB cable.
2. Press POINTER button on the remote control, and its flow follows as below:
1GND
2GND
3RX1
4CTS
5TX1
6RTS
IconAvailable button 
on the remote 
controlFunctions
PAGE UP/DOWN Scroll pages
ENTER Left click button
Directional buttons Move cursor
ESC Right click button
PAGE UP/DOWN Scroll pages
ENTER Enter button
Directional buttons the same as Keyboard directional buttons
ESC Esc button
ù ø
úû
üý
Normal mode
Mouse mode
Keyboard mode  
						

							
Printed in ChinaPart No. 1AA6P1P5587-- (KA7AA)SANYO Electric Co., Ltd.