Sanyo Pdg Dsu21n Projector User Manual

                                                                                                                                  EN-9
Package Contents
When you unpack the projector, make sure you have all these components:
Projector with Lens Cap AC Power CordVGA Cable (D-SUB to D-SUB)
(USA: J2552-0109-00) (UK: J2552-0108-00) (J2552-0072-03)
(Europe: J2552-0107-00)
Remote Control (IR)  Owner’s Manual Quick Start Guide
„Save the original shipping carton and packing material; they will comein handy if...

   EN-10
Projector Overview
Front View
Lens cap Ventilation holes
Elevator button AC power socket
Lens cap strap Zoom ring
Projection lens Focus ring
Front IR remote control sensor Control panel
Speaker Lamp cover
 1112910
71324685
17
28
39
410
511
612 

                                                                                                                                  EN-11
Rear View 
Connection ports
Kensington lock
Rear IR remote control sensor
Ventilation holes
Bottom View
Elevator foot
Ceiling mount (3-M4*6)
Tilt-adjustment foot
1324
1234
1
2
3
123
„This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package. 

   EN-12
Using the Product
Control Panel
LED
Button Function
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”. 
Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
ENTEREnter to sub-menu and confirm the menu selection. Activate in Color Setting, Lamp Counter
Reset and Factory Default menu operations.
AUTO PC
Resynchronize the projector to the input signal from a...

                                                                                                                                  EN-13
Connection Ports
AUDIO INConnect an audio output from video equipment to this jack.
COMPUTER IN / COMPONENT INConnect image input signal (Analog RGB or Component) to this jack.
RS-232C
Connect RS232C cable to RS232C port when operating the projector via a computer.
S-VIDEO IN
Connect S-Video output from video equipment to this jack.
VIDEO IN
Connect composite video...

   EN-14
Remote Control
INPUT
Manually select an input source.
AUTO PC
Resynchronize the projector to the input
signal from a computer.
NO SHOW
Hide the screen. Press again to cancel the NO
SHOW function.
FREEZE
Press “FREEZE” to pause the screen image.Press again to cancel the FREEZE function.
VOLUME + / -
Adjust the volume level.
PA G E  S / T(Computer mode only)
Scroll back and forth on the screen whengiving a presentation. Connect the projectorand your computer with a USB cable to usethese buttons....

                                                                                                                                  EN-15
Replacing the Battery
For the first time use:
Remove the transparent insulation tape by pulling it before use.
For battery change:
1. Remove the battery holder.
2.
Remove the old Lithium coin cell and install new one (CR2025). Ensure
that the side with the mark + is up.
3. Push the battery holder back into the remote control until you feel a 
click.
„Keep the battery out...

   EN-16
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from the front
„Operating the projector from the rear
1515
7m
1515
7m
„The remote control may not operate when there is sunlight or other strong light such
as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from a position where the remote sensor is visible.„Do not drop the remote control or jolt it.„Keep the remote control out of locations...

                                                                                                                                  EN-17
Installation
Connecting the Projector
Audio Cable VGA (D-SUB) to HDTV (RCA) Cable
VGA Cable (D-Sub to D-Sub) (supplied)S-Video Cable
RS-232C Cable Composite Video Cable
USB Cable
15
26
37
4
Desktop type Laptop type
4
6
2
7
1
1
3
5
„When connecting cable, power cords of both a projector and external equipment should 
be disconnected from AC outlet.
„The figure above is a...

   EN-18
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press I/  button to turn on the projector.
The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects
your source.
„If you are connecting multiple sources to the projector simultaneously, press the
INPUT button.
Warning:
„Remove the lens cap first...