Sanyo Pdg Det100l Projector User Manual

11
Terminals and Connectors
!0	R/C j ACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (not supplied).
q	
USB CONNECTOR (Series B)
  USB connector is used to service the projector. u	
S-VIDEO INPUT j ACK
  Connect the S-VIDEO output signal from video 
equipment to this jack. (p.21)
i	 SERIAL PORT IN TERMINAL
  If you control the projector by computer, you must 
connect a cable (not supplied) from your computer 
to this terminal.
o...

12
r	FOCUS  button
  Adjust the focus. (p.28)
e	
ZOOM button
  Zoom in and out the images. (p.28)
q	ON/STAND-B y button
  Turn the projector on or off. (pp.24,25)
!0	INPUT  button
    Select an input source INPUT 1, INPUT 2, Input 3 
or Input 4. (pp.32-34)
u	
AUTO PC AD j . button
  Automatically adjust the computer image to its 
optimum setting. (pp.28, 36)
y	 POINT  buttons
  -  Select an item or adjust the value in the On-
Screen MENU. (p.26)
   -  Pan the image in DIGITAL ZOOM + mode. (p.41)
Side...

13
Indicators
qw
e
r
t
y
u e	
wARNING TEMP  . indicator
  This indicator flashes red when internal projector 
temperature is too high. (pp.70, 77-79)
u	 LAMP 2 REPLACE indicator
    Turn orange when the life of the projection lamp2 
draws to an end. (
pp.66, 78)
q	
POwER indicator
  This indicator lights green when the projector 
is ready to be turned on. And it flashes green in 
Power Management mode. (pp.57, 77-79)
w	 LAMP Indicator
  This indicator is dim when the projector is turned 
on. And bright...

Remote Control
Part Names and Functions
q
t e
!0 i !4
r
!3
!1 w
y o !7
!2
!8
!9
@0
e	 LIGHT button
  Light the buttons on the remote control for about 10 seconds.
r  MENU button
  Open or close the On-Screen MENU. (pp.26-27)
t  POINT ed 7 8 buttons
   –  Select an item or adjust the value in the ON-SCREEN MENU. (p.26)
   –Pan the image in DIGITAL ZOOM +/– mode. (p.41)
y  LENS SHIFT button
  Select the LENS SHIFT function. (p.30)
u  FOCUS buttons
  Adjust the focus. (p.30)
i	 ZOOM buttons
  Zoom in and...

Remote Control Battery Installation
12 3
Open the battery 
compartment lid. Install new batteries into 
the compartment. Replace the 
compartment lid.
Two AA size batteries
For correct polarity (+ and –), 
be sure battery terminals are 
in contact with pins in the 
compartment.
To ensure safe operation, please observe the following precautions :
 l
 Use two (2) AA or LR6 type alkaline batteries.
 l  Always replace batteries in sets.
 l  Do not use a new battery with a used battery.
 l  Avoid contact with...

16
The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 56.
1
2
Remote Control Code
Part Names and Functions
Check the Reset Switch to...

17
Installation
Lens Installation
Before setting up the projector, install Projection Lens on the projector.
  Before installation, check where the projector is used and prepare a suitable lens. For the specifications of 
Projection Lens, contact sales dealer where you purchased the projector.
- Lens installation and replacement should be made by the qualified service personnel .
-   When setting the projector after lens installation, be sure to replace a Lens Cap to protect a surface.
-   
When carrying...

18
Projection lens can be moved from side to side and up and down with the motor-driven lens shift function. This 
function makes the positioning of images easy on the screen. (See page 28)
Lens Shift Adjustment
when the lens is shifted to top .
The display position can be 
shifted upward up to 55% 
elevation of the display.
when the lens is shifted to bottom .
The display position can be 
shifted downward up to 55% 
low level of the display.
when the lens is shifted to leftmost .
The display position...

19
Terminals of Projector
The projector has two replaceable Interface board slots. The projector's functions can be extended by installing 
the optional interface boards into the terminal slots. 1 vacant slot (Input 3) is provided in your purchasing the 
projector. For the Optional Interface Boards, contact sales dealer where you purchased the projector.
Pull out the interface board.Remove 2 Screws from an interface board.
1
2
Tighten screws to secure the interface board.
Replace the interface board....

20
Installation
Connecting to Computer
VGA 
Cable 
Monitor Output 
Desktop type
Laptop type
Terminals of
the projector DVI 
Cable 
BNC Cable Monitor 
Output 
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
G
V
H/HV
R
B
DIGITAL
ANALOG VGA 
Cable MONITOR 
OUT Monitor 
Output 
Monitor 
Input 
v
See the next page for the signals that can output 
to the MONITOR OUT terminal.v
Cables used for connection 
• VGA Cable (D-sub 15 pin) *
•...